Table of Contents
Advertisement
Quick Links
Installation, Operation & Maintenance Manual
Multi-Purpose
Short-Rise Lift
Model SRM10
10,000
. C
LBS
APACITY
2311 South Park Rd Louisville, Kentucky 40219
Email:
Web site:
sales@challengerlifts.com
www.challengerlifts.com
Office 800-648-5438 / 502-625-0700 Fax 502-587-1933
IMPORTANT:
READ THIS MANUAL COMPLETELY
BEFORE INSTALLING or OPERATING
LIFT
SRM10-IOM-A.doc
- 1 -
Rev. 02/21/19
Advertisement
Table of Contents
Related Manuals for Challenger Lifts SRM10
Summary of Contents for Challenger Lifts SRM10
- Page 1 Installation, Operation & Maintenance Manual Multi-Purpose Short-Rise Lift Model SRM10 10,000 APACITY 2311 South Park Rd Louisville, Kentucky 40219 Email: Web site: sales@challengerlifts.com www.challengerlifts.com Office 800-648-5438 / 502-625-0700 Fax 502-587-1933 IMPORTANT: READ THIS MANUAL COMPLETELY BEFORE INSTALLING or OPERATING LIFT SRM10-IOM-A.doc...
- Page 2 General Specifications See Figure 1A & 1B SRM10 SRM10 (Flush Mount) Rise Height 22" 17 3/4" Lowered Height 4 1/4" Lifting Capacity 10,000 lbs. (Hydraulic Pressure @ Cap.) (1720 PSI) Lock Heights 13 3/4", 18 3/8", 21 1/4" 9 1/2", 14 1/8", 17" Overall Width ...
- Page 3 Fig. 1B - General Flush Mount Layout VIEW A-A VIEW A-A VIEW A-A VIEW A-A Fig. 2 - Flush Mount Pit Layout (Provided By Others) SRM10-IOM-A.doc - 3 - Rev. 02/21/19...
-
Page 4: Before You Begin
OCATION This lift has been evaluated for indoor use only with an operating ambient temp. range of 5 – 40°C (41– 104°F) SRM10-IOM-A.doc - 4 - Rev. 02/21/19... - Page 5 Do For lift installation and operation, it is necessary this for your own protection. to have a dedicated 115V single-phase 60-cycle Challenger Lifts circuit with a 20-amp circuit breaker or time delay NOTIFY AT ONCE if any fuse.
- Page 6 Unit to suitable electrical source as shown in Fig 7. 11. Cycle the power unit (2 seconds on, 2 seconds off) until the hose expels a steady stream of fluid. 12. Connect the hose to the tee fitting on the lift. SRM10-IOM-A.doc - 6 - Rev. 02/21/19...
-
Page 7: Lock Release
Insert anchor bolts into holes but do not tighten yet. 20. For Surface Mount only, there are (8) 5/8” diameter holes in the ramp forms for use with ½” anchor bolts. Use the holes in the ramp SRM10-IOM-A.doc - 7 - Rev. 02/21/19... -
Page 8: Operation Procedure
Maintenance; and the employer shall insure that the lift maintenance personnel are qualified and they are adequately trained in the inspection of the lift. Owner/Employer shall maintain periodic inspection and maintenance records recommended lift manufacturer SRM10-IOM-A.doc - 8 - Rev. 02/21/19... - Page 9 D. Continue to raise to desired height ONLY if vehicle is secure on lift. Stub E. Once you have reached the required Fig. 5 Service Garage Lift Points height set into lock by depressing the lowering handle. SRM10-IOM-A.doc - 9 - Rev. 02/21/19...
-
Page 10: Lowering Vehicle
NOTE: The lock bar will reset automatically when the lift is fully lowered. If during the lowering process the lock bar resets before it gets to the fully lowered position, continue lowering by repeating steps 5 or 6 from above. SRM10-IOM-A.doc - 10 - Rev. 02/21/19... -
Page 11: Maintenance
SEMI-ANNUALLY: Check fluid level of lift power unit and refill if required. Use only Dexron III ATF or 10wt anti-foam, anti-rust hydraulic oil. If fluid is required, inspect hose and connections and cylinder seals. Repair as required. SRM10-IOM-A.doc - 11 - Rev. 02/21/19... -
Page 12: Parts Breakdown
ARTS REAKDOWN SRM10-IOM-A.doc - 12 - Rev. 02/21/19... - Page 13 Hardware Box (Flush Mount) SR10-004 Literature Pack Replace all worn, damaged, or broken parts with parts approved by Challenger Lifts Inc. or with parts meeting Challenger Lifts Inc. specifications. Contact your local Challenger Lifts Parts Distributor for pricing and availability.
- Page 14 Caution Decal 80-0151 Warning Decal Replace all worn, damaged, or broken parts with parts approved by Challenger Lifts Inc. or with parts meeting Challenger Lifts Inc. specifications. Contact your local Challenger Lifts Parts Distributor for pricing and availability. (Call Challenger Lifts Inc. (502) 625-0700 for the Parts Distributor in your area) SRM10-IOM-A.doc...
- Page 15 115VAC., Power Unit, 60Hz AB-1563-220 230VAC., Power Unit, 50/60Hz Replace all worn, damaged, or broken parts with parts approved by Challenger Lifts Inc. or with parts meeting Challenger Lifts Inc. specifications. Contact your local Challenger Lifts Parts Distributor for pricing and availability.