Section 7. Optional Remote Controls; Connecting To A Remote Pool-Off-Spa Selector (3-Wire Connection); Connecting To An Aqualink® Control System Or Remote Tstat (2-Wire Connection) - Jandy JXi 200 Installation And Operation Manual

Gas-fired pool and spa heater
Table of Contents

Advertisement

Jandy
, JXi
Gas-Fired Pool & Spa Heater
®
Section 8. Optional Remote Controls
The JXi heater controls can be wired for remote
operation. All Zodiac
AquaLink
®
permit the heater to be operated by remote control. The
instructions in the following sections should be used as a
general guideline only. Please follow the instructions that
accompany your selected control system thoroughly.
If you are setting up a new pool or spa system, or if you
have any questions about your heater control system,
please call Jandy technical support at 800.822.7933.
8.1

Connecting to a Remote Pool-Off-Spa Selector (3-Wire Connection)

Turn off the power to both the pool/spa control
system and the heater unit.
Follow service access instructions from
Run the wires from the pool/spa control system
through the low voltage knockout on the right or left
hand side of the heater.
8.1.1
Configure the Control Panel:
Make sure the pool heater is OFF.
Press and hold MENU, then the POOL and SPA
buttons for 5 seconds to access Service Setup mode.
NOTE: The display will revert back to OFF 1 minute after the last key press.
Press Up or Down to display REMOTE.
8.2
Connecting to an AquaLink® Control System or Remote TSTAT (2-Wire Connection)
An interrupt (on/off-type) remote can be connected as
a Remote TSTAT to turn the heater on or off but not
perform any other function. When using this type of
8.2.1
Install the Remote TSTAT:
Turn off the power to both the pool/spa control
system and the heater unit.
Follow service access instructions from
Run the wires from the pool/spa control system
through the low voltage knockout on the right or left
hand side of the heater.
NOTE: If you install a time clock to control the filter pump operation, it is recommended that the time clock have its own low voltage (Fireman's) switch
to turn off the heater before turning off the pump. The switch should shut off the heater about 15 minutes before the filter pump shuts off. This will allow
for a more efficient operation by removing any residual heat contained in the heat exchanger back to the pool.
To avoid damage to the heater, do not connect the power supply of the heater to the output side of the clock if your time clock simply
interrupts the high voltage power supply or has a high voltage output. Doing so will prevent the blower from purging the residual heat from the
heater when the heater turns off. The blower must be allowed to run for 45 seconds after the heater shuts off.
|
Installation & Operation Manual
Control Systems will
®
Section
6.1.
Section
6.1.
CAUTION
Electrical wiring must be in accordance with the latest
edition of the National Electrical Code (NEC), ANSI
National Fire Protection Association
local code requirements indicate otherwise.
Refer to
Figure 16
for a complete diagram of wiring
connections and terminals.
Consult with Jandy Technical Support, 800.822.7933 for
questions about installing non-Zodiac remote controls.
Connect the wiring from the pool/spa control system to the
heater remote control terminal. See
Connect the three wires to the Spa, Pool & Common
terminals of the J6 terminal bar.
Reinstall front panel.
Restore power to the heater and the
pool/spa control system.
Press MENU, REMOTE OFF (default) is displayed.
Use Up or Down to scroll through the Remote
options until HI-LO-COM is displayed, then press
MENU to select.
Press POOL or SPA to exit Service Setup mode.
connection, remember to set the heater control to "pool"
or "SPA" and set the thermostat control to maximum.
Connect the wiring from the pool/spa control system
to the heater remote control terminal.
Connect the two wires to Pool and Common (not
Spa) on the J6 terminal bar. See
Reinstall panel.
Restore power to the heater and the pool/spa
control system.
Page 29
ENGLISH
(NFPA70
), unless
®
®
Figure 16
item "b".
Figure 16
item "b".
/
®

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Jxi 260Jxi 400Jxi200 seriesJxi260 seriesJxi400 seriesJxi200n ... Show all

Table of Contents