Master Bilt MCR-33101 Installation & Operation Instructions page 45

Blast Chiller Default List of configuration parameters
The following table illustrates the meaning of the configuration parameters.
PAR Description
CA1 Cabinet probe offset
CA2 Need probe offset
CA3 Evaporator probe offset
CA4 Condensor probe offset
CA5 Needle probe offset 2
CA6 Needle probe offset 3
Probe type:
P0 0 = PTC
1 = NTC
Temperature unit of measurement
P2 0 = ºC
1 = ºF
Number of needle probe sensor
P3
0 = 0; 1 = 1; 2 = 2; 3 =3
P4 Enabling the evaporator probe
P5 Enabling condenser probe
Orientation of the display Visualization
P8 0 = device located at the top as the unit
1 = device located at the bottom as to the unit
Operation Parameters
PAR Description
r0 Temperature differential (r7 – r12)
r1 Duration of Time-Controlled blast chilling
r2 Duration of Time-Controlled blast Freezing
r3 Temperature-controlled blast chilling & soft deep freezing temperature
r4 Temperature-controller deep freezing temp. (see also r6)
r5 Max duration of Temperature-controlled blast chilling (see also r3)
r6 Max duration of Temperature-controlled deep freezing (see also r4)
r7 Box temperature set-point for blast chilling & soft deep freezing
r8 Box Temperature setpoint during deep freezing (see also r0)
r9 Box Temperature setpoint during HARD blast chilling (see also r0)
r10 Box Temperature setpoint post blast chilling STORAGE (see also r0)
r11 Box Temperature setpoint post deep freezing STORAGE (see also r0)
r12 Box Temperature setpoint during Pre-Cooling (see also r0)
r13 Hard blast chilling end temperature setpoint (needle probe)
r14 Time-control hard blast chilling & Soft deep freezing
r15 Temperature below which count the max blast chilling & deep freezing
Type of operating cycle that can be selected
0 = blast chilling & Storage only
r16
1 = blast chilling & Storage or deep freezing & storage
2 = deep freezing & store only
Min temperature difference between needle probe and box temperature
r17
0 = Test will not be perform
r18 Duration of second phase test for correct insertion of needle probe
r19 Reserved
45
Unit Range ºC
°C/°F -25 to 25
°C/°F -25 to 25
°C/°F -25 to 25
°C/°F -25 to 25
°C/°F -25 to 25
°C/°F -25 to 25
... 0 / 1
... 0 / 1
... 0 / 3
... 0 / 1
... 0 / 1
... 0, 1
Unit Range ºC
°C/°F 1 – 15 5/7
Min 1 – 500
Min 1 – 500 240
°C/°F -99 – 99
°C/°F -99 – 99 -18
Min 1 – 500
Min 1 – 500 240
°C/°F -99 – 99
°C/°F -99 – 99 -26
°C/°F -99 – 99
°C/°F -99 – 99
°C/°F -99 – 99 -18
°C/°F -99 – 99
°C/°F -99 – 99
% 10 – 100
°C/°F -99 – 99
... 0 – 2 0 / 2
°C/°F 0 – 99
Second 1 – 99
... ...
ºF
0 0
0 0
0 0
0 0
0 0
0 0
1 1
1 1
3 3
1 1
0 0
1 1
ºF
5/7
90 90
240
3 37
0
90 90
240
0 32
-15
-4 25
2 36
0
5 41
15 59
60 60
65 149
0 / 2
5 5
60 60
... ...