Sub-Zero PRO 48 Series Installation Manual
Hide thumbs
Also See for PRO 48 Series:
- Installation instructions manual (76 pages) ,
- Use & care manual (44 pages) ,
- Installation manual (32 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for Sub-Zero PRO 48 Series
Summary of Contents for Sub-Zero PRO 48 Series
- Page 1 INSTALLATION GUIDE PRO 48 Refrigeration...
-
Page 2: Table Of Contents
PRO 48 Refrigeration ......3 To ensure the safe and efficient installation of Sub-Zero equipment, please take note of the following types of PRO 48 Specifications . -
Page 3: Pro 48 Refrigeration
Allen, standard and crescent wrenches. Any questions or problems regarding the installation • Various sized pliers. should be directed to your authorized Sub-Zero dealer or • " hex bolt nut driver. Sub-Zero customer service at 800-222-7820. You may also check the contact & support section of our website, •... -
Page 4: Pro 48 Specifications
PRO 48 Specifications Overall Dimensions MODELS 648PRO AND 648PROG 48" " (1219) (657) 84" (2134) " (1070) " (775) 4" (102) HEIGHT DIMENSIONS ± 1 " (13) " (767) " (606) " 21" (533) (368) SPECIFICATIONS " Capacity / Weight (781) INTERIOR CAPACITY R CU FT... -
Page 5: Pro 48 Site Preparation
PRO 48 Site Preparation subzero.com/specs Opening Dimensions STANDARD AND FLUSH BUILT-IN INSTALLATIONS TOP VIEW OPENING DEPTH OPENING OPENING OPENING DEPTH HEIGHT WIDTH SIDE VIEW FRONT VIEW IMPORTANT NOTE: For standard built-in installations, the Opening Dimensions Standard Flush face frame of the unit will extend 2" (51) beyond cabinetry. Opening Width "... - Page 6 PRO 48 Site Preparation Electrical Requirements For PRO 48 models, the electrical supply should be located within the shaded area shown in the illustration The outlet must be checked by a qualified electrician to below. Follow the National Electrical Code and local codes be sure that it is wired with the correct polarity.
- Page 7 Do not use self-piercing valves. A saddle valve kit is available through your authorized " BACK WALL (13) Sub-Zero dealer. 6" 18" (457) A reverse osmosis system can be used, provided there (152) is constant water pressure of 20 psi (1.4 bar) to 120 psi...
-
Page 8: Pro 48 Installation
PRO 48 Installation Anti-Tip Bracket Installation IMPORTANT NOTE: For either wood or concrete floor applications, if the wood screws do not hit a wall stud in To prevent the PRO 48 from tipping forward and any of the upper holes on the anti-tip bracket, use the provide a stable installation, the unit must be secured provided #8–18 x 1 "... - Page 9 PRO 48 Installation subzero.com/specs Anti-Tip Bracket Installation WOOD FLOOR APPLICATIONS INSTALL CONCRETE WEDGE ANCHORS: Use the twelve #12 x 2 " wood screws and the twelve 1) Drill a " (10) diameter hole any depth exceeding the #12 flat washers provided. Drill pilot holes "...
- Page 10 PRO 48 Installation Unpack the Unit Grille Removal Uncrate the PRO 48 unit and inspect for any damages. In order to prevent damage to the PRO 48 grille, the top Remove the wood base and discard the shipping bolts grille assembly should be removed prior to moving the and brackets that hold the wood base to the bottom of the unit.
- Page 11 PRO 48 Installation subzero.com/specs Position the Unit IMPORTANT NOTE: If for any reason the unit has been laid on its back or side, you must allow the unit to stand Before moving the PRO 48 unit into position, secure upright for a minimum of 24 hours before connecting doors and drawers closed and protect any finished power.
- Page 12 PRO 48 Installation Water Line Connection Level the Unit Approximately 3' (.9 m) of " plastic tubing is connected Once the unit is in position, extend the front leveling legs to the ice maker with a preassembled " compression down by turning the legs counterclockwise and adjust the connection at the end.
- Page 13 PRO 48 Installation subzero.com/specs Door Adjustment Make sure both doors of the PRO 48 are properly aligned for function and appearance. If not, adjustments can be The doors of the PRO 48 are very heavy. Use care when made to the cabinet hinges. removing them.
- Page 14 PRO 48 Installation Drawer Adjustment Make sure all drawers of the PRO 48 are properly aligned HORIZONTAL ADJUSTMENT for function and appearance. If not, vertical and horizontal 1) Loosen the two front drawer slide screws. Refer to the adjustments can be made to the drawers. illustration below.
- Page 15 90° door stop kit is available through your authorized base. Refer to the illustration below. Sub-Zero dealer. To obtain local dealer information, visit the find a showroom section of our website, subzero.com. IMPORTANT NOTE: The kickplate must be removable for service.
- Page 16 PRO 48 Installation Water Filtration System WATER FILTER BYPASS MODE If you choose not to use the water filtration system, the system can be placed in water filter bypass mode by WATER FILTER removing the water filter cartridge. In this mode, the water supplied to the ice maker will not be filtered and the water filter monitor will be deactivated.
- Page 17 Have stainless steel surfaces been inspected for any imperfections? This is to be done by the authorized Sub-Zero dealer or installer with the customer, upon completion of installation. Stainless steel surfaces are covered by a limited 60-day warranty for cosmetic...
-
Page 18: Service Information
Service Information If service is necessary, maintain the quality built into your PRO 48 unit by calling Sub-Zero factory certified service. If you are storing or disposing of your old refrigerator or For the name and number of Sub-Zero factory certified freezer, please do it safely. - Page 19 The information and images in this guide are the copyright property of Sub-Zero, Inc. Neither this guide nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Sub-Zero, Inc. ©Sub-Zero, Inc. all rights reserved.
- Page 20 SUB-ZERO, INC. P. O. BOX 44848 MADISON, WI 53744 SUBZERO.COM 800.222.7820 7020379 REV-A 10/ 2010...