Table of Contents
Advertisement
Quick Links
INSTALLATION CERTIFICATE
The undersigned qualified installer attests to have personally fitted the alarm system on the here
described vehicle following the manufacturer instructions.
By :
932IT
Sold on :
Type of device :
932IT
................................................
Vehicle :
..........................................................................................................................
INSTALLATION AND
USER GUIDE
UK
GEMINI Technologies S.r.l.
Via Luigi Galvani 12 - 21020 Bodio Lomnago (VA) - Italy
Tel. +39 0332 943211 - Fax +39 0332 948080
www.gemini-alarm.com
Rev.02 - 06/17
ISO 9001 Certified Company
Made in Italy
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Gemini 932IT
Summary of Contents for Gemini 932IT
- Page 1 932IT ..........Vehicle : .......................... INSTALLATION AND USER GUIDE GEMINI Technologies S.r.l. Via Luigi Galvani 12 - 21020 Bodio Lomnago (VA) - Italy Tel. +39 0332 943211 - Fax +39 0332 948080 www.gemini-alarm.com Rev.02 - 06/17 ISO 9001 Certified Company...
-
Page 2: Table Of Contents
2.1 - SYSTEM TOTAL ARMING - CONNECTIONS TO ARM/DISARM THE SYSTEM Press the vehicle original remote control lock button or button “1” on a Gemini remote control. If the 6.1 - Connections and operation via CAN BUS line optical/acoustic signals have been enabled, arming will be confirmed by 1 flash of the turn indicators 6.2 - Connections to locking motors... -
Page 3: Passive Arming
When the system arms automatically, internal sensors are not enabled. doors are locked via the vehicle original remote control or via a Gemini remote control but will not Opening a door 60 sec. before the system is armed will cause the procedure to interrupt;... -
Page 4: Optional Devices And Battery Replacement
3.3 - RFID TRANSPONDER - 908 to disable the engine immobilizer. 2.0 - FUNZIONAMENTO TELECOMANDO E SOSTITUZIONE BATTERIA 3.0 - OPTIONAL DEVICES AND BATTERY REPLACEMENT To activate the transponder simply presss the button and keep it pressed for at least 4 sec. The LED Remote controls have a low charge battery indicator that gives early warning to avoid malfunctioning. -
Page 5: Installer Manual
ORANGE negative output during alarm BLACK marked “G” (siren, pager, tracker) Ignition For more complete information regarding connections, refer to the supported vehicle models installation instructions at www.gemini-alarm.com private area). PAGE 08 - INSTALLER MANUAL INSTALLER MANUAL - PAGE 09... -
Page 6: Connections To Arm/Disarm The System
7.0 - VEHICLE CODE PROGRAMMING 932IT alarm system can operate in various modes according to the vehicle on which it is installed The system must be configured based on the vehicle model on which it is installed. and the available connections. -
Page 7: System Programming
With the system disarmed, turn ignition key “ON” and, while the LED is ON, touch the key to its receptacle. For Gemini only: Turn ignition key ----- A lack of power during electrical system maintenance, will not affect the programming. -
Page 8: Deleting Programmed Devices
• The system is ready to receive the device codes. Turn ignition key “OFF” and then back “ON” to • Depending on which device is to be stored in memory, either press one of the buttons on the disable the function. remote control, touch the key to its receptacle have the transponder transmit, make the magnetic... -
Page 9: Ultrasonic Volumetric Protection
ULTRASONIC VOLUMETRIC PROTECTION 14.0 - TECHNICAL SPECIFICATIONS 12.1 CONNECTIONS AND POSITIONING Power supply 12 Vdc • Insert the WHITE connector in the “W” socket. Current absorption @ 12Vdc with system armed and LED flashing 15mA • Insert the RED connector in the “R” socket. Working range temperature -30°C to +70°C •...
Need help?
Do you have a question about the 932IT and is the answer not in the manual?
Questions and answers