Parameters List - Emerson Dixell iChill IC200D EVO Series Installing And Operating Instructions

50. PARAMETERS LIST

Parameter Description
ST 1 Chiller Setpoint
ST 2 Chiller minimum Setpoint
ST 3 Chiller maximum Setpoint
ST 4 Heat pump setpoint
ST 5 Heat pump minimum Setpoint
ST 6
Heat pump maximum Setpoint
ST 7 Regulation band in chiller mode
ST 8
Regulation band in chiller heat pump
ST 9 Regulation probe selection in chiller
0= Temperature probe NTC for evaporator inlet
1= Temperature probe NTC for evaporator outlet 1
2= Temperature probe NTC for evaporator outlet 2
3= Temperature probe NTC for common evaporator outlet
4= Temperature NTC probe from remote panel 1
5= Temperature NTC probe from remote panel 2
ST 10 Regulation probe selection in heat pump
0= Temperature probe NTC for evaporator inlet
1= Temperature probe NTC for evaporator outlet 1
2= Temperature probe NTC for evaporator outlet 2
3= Temperature probe NTC for common evaporator outlet
4= Temperature NTC probe from remote panel 1
5= Temperature NTC probe from remote panel 2
6= Temperature probe for water common inlet of the condenser
7= Temperature probe for water inlet of the circuit # 1 condenser
8= Temperature probe for water inlet of the circuit # 2 condenser
9= Temperature probe for water outlet of the circuit # 1 condenser
10= Temperature probe for water outlet of the circuit # 2 condenser
11= Temperature probe for water common otlet of the condenser
ST 11 Type of thermoregulation
0= Proportional
1= Neutral zone
Parameter Description
dP 1
Default read-out of the top display
dP 2 Default read-out of the bottom display
dP 3 Default display read-out configuration top / bottom
0= Configurable
1= Top display: Evaporator IN, Bottom display: Evaporator OUT
2= Top display: Condenser IN, Bottom display: Condenser OUT
3=Top display: temperature/Condensing pressure, Bottom Display:
evaporating pressure
dP 4 Top display default read-out of the remote terminal_1
0= the read-out depends on the paremeters dP01 – dP02 – dP03
1= the read-out shows the NTC probe of the remote panel.
dP 5
Top display default read-out of the remote terminal_2
0= the read-out depends on the paremeters dP01 – dP02 – dP03
1= the read-out shows the NTC probe of the remote panel.
dP 6 Visograph: firs probe visualized
dP 7
Visograph: second probe visualized
dP 8 Visograph: third probe visualized
dP 9 Visograph: fourth probe visualized
dP 10 Visualization in STD-BY
0= "STD-BY"
1= same visualization of dP1 and dP2
2= "OFF"
Parameter Description
CF 1 Type of unit
0= Air / air Chiller
1= Air / water Chiller
2= Water / water Chiller
1592015610 User manual IC200D EVO GB rel1.0 10.11.2015_rev10
Visualizzazione display
Unità
IC200D
min max M. u. Resolution
ST02 ST03 °C/°F
-50.0 °C
ST01
-58 °F
110 °C
ST01
230 °F
ST05 ST06 °C/°F
-50.0 °C
ST04
-58 °F
110 °C
ST04
230 °F
0.1 25.0 °C
0 45 °F
0.1 25.0 °C
0 45 °F
0 5
0 11
0 1
min max M. u. Resolution
0 16
0 20
0 3
0 1
0 1
0 39
0 39
0 39
0 39
0 2
min max M. u. Resolution
0 2
dec/int
Dec
int
Dec
int
dec/int
Dec
int
Dec
int
Dec
int
Dec
int
144/192