L860 Elevated Low-Intensity Edge Light Warranties Warranties WARRANTY FOR GOODS AND SERVICES: Seller warrants, to the extent to which any of the same may be applicable, that (a) on the date of shipment the goods are of the kind and quality described herein and are free of non-conformities in workmanship and material, (b) the engineering services performed by it will be performed in accordance with generally...
Page 6
This manual could contain technical inaccuracies or typographical errors. ADB Airfield Solutions reserves the right to revise this manual from time to time in the contents thereof without obligation of ADB Airfield Solutions to notify any person of such revision or change.
L860 Elevated Low-Intensity Edge Light Safety Section 1 Safety This section contains general safety instructions for using your ADB 1. Safety Airfield Solutions equipment. Some safety instructions may not apply to the equipment in this manual. Task- and equipment-specific warnings are included in other sections of this manual where appropriate.
Use this equipment only as described in this manual. ADB Airfield Solutions cannot be responsible for injuries or damages resulting from nonstandard, unintended applications of its equipment. This equipment is designed and intended only for the purpose described in this manual.
WARNING: Failure to follow these safety procedures can result in personal injury or death. • Allow only qualified personnel to install ADB Airfield Solutions and auxiliary equipment. Use only approved equipment. Using unapproved equipment in an approved system may void agency approvals.
Allow only qualified personnel to perform maintenance, 8. Maintenance and Repair troubleshooting, and repair tasks. Only persons who are properly trained and familiar with ADB Airfield Solutions equipment are permitted to service this equipment. • Always use safety devices when working on this equipment.
Page 11
8. Maintenance and Repair after servicing equipment. Ground all conductive equipment. (contd.) • Use only approved ADB Airfield Solutions replacement parts. Using unapproved parts or making unapproved modifications to equipment may void agency approvals and create safety hazards. • Check interlock systems periodically to ensure their effectiveness.
Annex 14, Vol. 1 para. 5.3.5 for use on a non- precision instrument runway. The ELIL can be supplied with or without a heater (arctic kit). NOTE: Signature Series is a trademark of ADB Airfield Solutions. Glassware Assembly LED Assembly...
L860 Elevated Low-Intensity Edge Light Description See Figure 2-1 for the main items in the assembly. The ELIL is 1. Introduction (contd.) assembled at the factory and is ready for installation. The ELIL is typically supplied with a 1-1/2 -12 UNF threaded frangible coupling for mounting on a L-867B light base.
L860 Elevated Low-Intensity Edge Light Description Table 2-3 Required Equipment Not Supplied 2. L-860 LED Elevated Light Description Quantity Fixture: Required Torque wrench (0 to 200 inch-pounds) Equipment (contd.) required) Loctite number 243 or equivalent As required L-867B light baseplate with 1-1/2−12 UNF or L-867B (if required) or L-867D light base with 2-inch NPT.
L860 Elevated Low-Intensity Edge Light Section 3 Installation WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation. This section provides instructions for installing the L-860 low 1.
L860 Elevated Low-Intensity Edge Light This subsection provides installation instructions for the L-860 light 4. Installation fixtures. L-860 light fixtures can be mounted on an L-867 base plate with a Base Mounting diameter and bolt-hole corresponding to either a 12-inch- (304.8 mm-) diameter L-867B base or a 16-inch- (406.4 mm-) diameter L- 867D base plate per FAA AC 150/5345-46.
Page 18
L860 Elevated Low-Intensity Edge Light 7. There are three power wires present at the bottom of the fixture: Light Base Mounting Brown (Line), Blue (Neutral) and Green (Earth Ground). Place the (cont’d) assembled base plate/fixture close to the base can. 8.
L860 Elevated Low-Intensity Edge Light Troubleshooting Section 4 Maintenance This section provides maintenance information for the L-860 ELIL LED 1. Introduction elevated light. To keep the L-860 light fixtures operating efficiently, follow a 2. Maintenance Schedule preventive maintenance schedule. Refer to Table 4-1. Refer to FAA AC 150/5340-26 for more detailed information.
L860 Elevated Low-Intensity Edge Light Troubleshooting NOTE: The L-860 ELIL elevated light is assembled at the factory. Use 3. Assembly Instructions the assembly instructions below when you need to disassemble/ assemble parts for repair or maintenance purposes. To assemble parts, perform the following procedure: 1.
This information covers only the most common problems that you may encounter. If you cannot solve the problem with the information given here, contact your local ADB Airfield Solutions representative for help. Refer below for troubleshooting procedures for the L-860 LED 2.
L860 Elevated Low-Intensity Edge Light Repair Section 6 Repair WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation. WARNING: De-energize the circuit and lock out the circuit or regulator so that the circuit cannot be energized by remote means before attempting to service the fixture.
Page 23
L860 Elevated Low-Intensity Edge Light Repair 2. Access to Internal Components (contd.) 3. Remove the glassware assembly, see caution above, and unscrew the glassware assembly from the fixture by rotating it counterclockwise. Separate the glassware assembly from the housing. If the LED or arctic kit must be removed and replaced 3.
Page 24
L860 Elevated Low-Intensity Edge Light Repair 1. All items in the Glassware Assembly are replaceable. ADB 5. Glassware and O-Ring recommends that if the glass is broken replace o-ring seal along Seal Replacement with the new glassware. If the o-ring seal is leaking replace it with a new o-ring.
L860 Elevated Low-Intensity Edge Light Parts Section 7 Parts To order parts, call ADB Airfield Solutions Customer Service or your 1. Introduction local representative. Use this four-column parts list, and the accompanying illustration, to identify and order parts correctly. Using the Illustrated Parts List This subsection describes how to use the illustrated parts list covered later in this section.
L860 Elevated Low-Intensity Edge Light Parts ELIL - X X X X 0 ARCTIC OPTION 0 = WITHOUT ARCTIC KIT 1 = WITH ARCTIC KIT COLUMN HEIGHT 1 = 14" OAH WITH 1-1/2" COUPLING 2 = 24" OAH WITH 1-1/2" COUPLING 3 = 30"...
L860 Elevated Low-Intensity Edge Light Parts Equipment not Shown but Required Orient glassware assembly integral to led lamp color assembly of LED mount EXAMPLE 1: 64A0957-06 Red glass with red LED 6-32 PAN HD PHIL W/CAPTURED EXT STAR WASHER EXAMPLE 2: 67A0033 Green glass with green LED, obscured THERMAL JOINT COMPOUND...