1. Manuals
  2. Brands
  3. molex Manuals
  4. Crimp tool
  5. 207129 Series
  6. Specification sheet

molex 207129 Series Specification Sheet

Hand crimp tool for standard 2.36mm (.093") diameter pin and socket terminals
Hide thumbs Also See for 207129 Series:
1
2
3
4
5
Table of Contents

Advertisement

Quick Links

Download this manual
Hand Crimp Tool for Standard 2.36mm (.093") Diameter Pin and Socket Terminals

FEATURES

Simple trouble-free full cycle mechanism assures consistent complete terminations
All crimp cavities are fully machined in high carbon steel, then heat treated

SCOPE

Products: 2.36mm (.093") Diameter, Standard .093" Pin and Socket Crimp Terminal, 22-24 AWG.
Terminal
Series No.
Loose Piece
2870
02-09-2137
2871
02-09-1137 02-09-1139 02-09-1136 02-09-1138 22-24 0.35-0.20 1-27-1.78 .050-.070 3.96-5.53 .156-.218
Follow the Cut-Off Tab specifications on Applicator specification sheets. These Terminals cannot be removed
from the reel by manual cutting. An applicator must be used or the terminals will not function properly.

DEFINITION OF TERMS

BRUSH
STRIP
LENGTH
Terminal is to be centrally located between the two (2) cut-off tab edges by one half of the total cut-off tab
tolerance.
This illustration is a generic terminal representation and not an exact image of any terminal listed in the scope.
Doc No: ATS-011010097
Revision: D
Hand Crimp Tool
Specification Sheet
Order No. 11-01-0097
Engineering No. HTR7176
Terminal Order No.
Reel
02-09-2136 02-09-2138 22-24 0.35-0.20 1-27-1.78 .050-.070 3.96-5.53 .156-.218
BELL MOUTH
SEAM
INSULATION
CRIMP
CONDUCTOR
CRIMP HEIGHT
CRIMP
Release Date: 11-29-04
Revision Date: 04-18-08
Wire Size
Insulation Diameter
AWG
mm²
mm
BEND UP
ROLLING
TWISTING
BEND
DOWN
UNCONTROLLED COPY
TYPE 3
Strip Length
In.
mm
In.
C/L
TERMINAL
LOCATION
CUT-OFF
TAB
C/L
Page 1 of 5

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 207129 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for molex 207129 Series

Summary of Contents for molex 207129 Series

  • Page 1 Hand Crimp Tool for Standard 2.36mm (.093") Diameter Pin and Socket Terminals Hand Crimp Tool Specification Sheet Order No. 11-01-0097 Engineering No. HTR7176 TYPE 3 FEATURES Simple trouble-free full cycle mechanism assures consistent complete terminations All crimp cavities are fully machined in high carbon steel, then heat treated SCOPE Products: 2.36mm (.093") Diameter, Standard .093"...
  • Page 2 The insulation should be stripped long (1/2 in.) so the insulation grips on the terminal do not grip the wire insulation or the conductor. Refer to Molex Quality Crimping Handbook 63800-0029 for additional information on crimping and crimp testing.
  • Page 3 Hand Crimp Tool for Standard 2.36mm (.093") Diameter Pin and Socket Terminals 4. Depress the spring loaded wire stop on the locator and carefully remove the crimped terminal. See Figure 3. Note: The tamper proof ratchet action will not release the tool until it has been fully closed. TERMINAL DEPRESS THE WIRE STOP ON...
  • Page 4 3. This tool is intended for standard conductor sizes. It may not give a good insulation crimp support for all insulation sizes. 4. Molex does not repair hand tools (see warranty above) The replacement parts listed are the only parts available for repair. If the handles or crimp tooling is damaged or worn, a new tool must be purchased.
  • Page 5 2222 Wellington Ct. 1-800-78MOLEX 81-462-65-2324 65-6-268-6868 49-89-413092-0 Lisle, IL 60532 U.S.A. amerinfo@molex.com feninfo@molex.com fesinfo@molex.com eurinfo@molex.com 630-969-4550 Fax: 630-969-1352 Visit our Web site at http://www.molex.com UNCONTROLLED COPY Doc No: ATS-011010097 Release Date: 11-29-04 Page 5 of 5 Revision: D Revision Date: 04-18-08...

This manual is also suitable for:

Htr717611-01-0097

Table of Contents