Riello Condexa PRO Series Installation, Technical And Maintenance Manual page 42

INSTALLATION
Nr. dis-
Par.
Menu played
No.
Display
Min.
M1 15 Power
CH/DHW
Defines the proportional parameter for modulation
M1 16 CH PID P
Defines the modulation integral term during heat-
M1 17 CH PID I
Defines the modulation derivative term during
M1 18 CH PID D
Design
Defines the max. set-point at the minimum out-
M1 19 Supply
Temp.
Design Defines the minimum outdoor temperature to
M1 20 Outdoor which the maximum set-point can be associated
Temp.
Baseline
Defines the minimum set-point at the maximum
M1 21 Supply
Temp.
Baseline Defines the maximum minimum outdoor tem-
M1 22 Outdoor perature to which the minimum set-point can be
Temp.
Design
Limits the minimum value that can be assigned to
Supply
M1 23 the set-point in heating mode (does not apply to
Min.
Limit
Design
Limits the maximum value that can be assigned to
Supply
M1 24 the set-point in heating mode (does not apply to
Max.
Limit
Warm
Defines the temperature at which climatic regula-
M1 25 Weather
Shutdn
Establishes the set-point temperature increase
Boost
delta T, if the heat demand in heating mode is not
M1 26 Temp In-
satisfied after the time interval specified in Par. 27
crement
Boost Defines the time interval after which the set-point
M1 27 Time is increased as defined in Par. 26 (applies only to
Delay
Used in heating mode Par. 1= 2 or 3. Establishes
Night
by how many degrees the delivery set-point is
M1 28 Setback
reduced when the RT (room thermostat/heat de-
Temp.
DHW Establishes the domestic hot water circuit's opera-
M1 35
mode
Max.
Defines the domestic hot water circuit's % max.
M1 113 Power
DHW
Min.
Defines the domestic hot water circuit's % mini-
M1 114 Power
DHW
DHW
Tank Defines the hysteresis to initiate the domestic hot
M1 36
Hyst.
Down
DHW
Defines the hysteresis to stop the domestic hot
M1 37 Tank
Hyst. Up
DHW
Defines the primary circuit's set-point increase in
Tank
M1 38 degrees compared to the temperature set for the
Supply
Extra
Description
Sets the heating's % min. power.
during heating operation.
ing operation.
heating operation.
door temperature for climatic regulation.
for climatic regulation.
outdoor temperature for climatic regulation.
associated for climatic regulation.
heating mode 4).
heating mode 4).
tion is switched off.
(applies only to stand-alone mode).
stand-alone mode).
mand) contact is closed.
tion mode.
power.
mum power.
water demand.
water demand.
domestic hot water tank.
Range
1...30
0...1275
0...1275
0...1275
30...90
-25...25
30...90
0...30
4...82
27...90
0...35
0...30
1...120
0...30
0 Disabled 1 Tank
+ sensor 2 Tank +
thermostat
50...100
1...30
0...20
0...20
0...30
42
Default Access
UM Category
setting type
1 % I
100 O
250 O
0 O
80 °C U
0 °C U
40 °C I
20 °C I
30 °C I
80 °C I
22 °C I
0 °C I
20 Min. I
10 °C I
0 I
100 % I
1 % I
5 °C I
5 °C I
15 °C I
Heating
Heating
Heating
Heating
Heating
Heating
Heating
Heating
Heating
Heating
Heating
Heating
Heating
Heating
DHW
DHW
DHW
DHW
DHW
DHW