Advertisement
Quick Links
ASSEMBLY, INSTALLATION, AND OPERATION INSTRUCTIONS
Maximum load weight limit is 40 lbs per bicycle. Rack empty weight is 20 lbs.
To register your product, visit the LetsGoAero.com/registration
Let's Go Aero, Inc. 4474 Barnes Road Colorado Springs, CO 80917, USA
NOTICE: All Manual information is subject to change without notice. Revised editions
will be available for free download at LetsGoAero.com. Manual information is considered
factual until made obsolete by a revised version.
Follow this QR-Code or visit
LetsGoAero.com/manuals to check for an updated version:
Copyright© 2019, Lets Go Aero, Inc., All rights reserved.
BW-B01861-121219Rev
PRODUCT MANUAL
For 1.25in & 2in Hitch Receivers
For More Information & Accessories:
Visit our Website - www.LetsGoAero.com
For Technical Support & Product Questions:
Contact Us at 877-464-2376 or 719- 630-3800
Email: Support@LetsGoAero.com
Patent and trademark protected:
Patent Number 8,889,456; Patents Pending
Page 1 of 9
Tilting Hitch V-Rack™ Carrier for Two Bikes
BikeWing
Part No. B01861
PARTS
QTY. DESCRIPTION
A
1
SHANK
B
1
2IN HITCH ADAPTER
C
2
6MM SOCKET HEAD BOLT
D
1
NOMOTION™ HITCH PIN
E
1
LOCK WASHER
F
1
FLAT WASHER
G
1
LARGE RETAINER CLIP
H
1
STEM
J
1
WIRE LOCK PIN
K
2
10mm BOLT
L
4
10mm FLAT WASHER
M
2
10mm NYLOCK NUT
N
2
RING PIN
O
8
CRADLE HOUSING
P
2
WING
Q
4
UPPER WHEEL CRADLE
R
4
LOWER WHEEL CRADLE
S
8
RUBBER STRAP
T
8
SMALL RETAINER CLIP
Revision Date: 12/12/19
-2
®
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Let's Go Aero BikeWing-2
Summary of Contents for Let's Go Aero BikeWing-2
- Page 1 BikeWing ® Tilting Hitch V-Rack™ Carrier for Two Bikes Part No. B01861 PRODUCT MANUAL ASSEMBLY, INSTALLATION, AND OPERATION INSTRUCTIONS Maximum load weight limit is 40 lbs per bicycle. Rack empty weight is 20 lbs. For 1.25in & 2in Hitch Receivers PARTS QTY.
- Page 2 STEP 1: INSTALLATION (FOR 1.25IN HITCHES ONLY) FOR 1.25IN HITCH RECEIVERS [Fg. 1] ONLY Vehicles with 2in Hitches must skip this step. For vehicles with 1.25in hitches unbolt the two 6mm Socket Head Bolts [C] connecting the factory installed Hitch Adapter [B] to the end of the Shank [A] and removed the Hitch Adapter.
- Page 3 STEP 4: RECOMMENDED TOOL: 15mm Wrench & 6mm Hex Tool Remove the pre-attached Wire Lock Pin [J] and let is hang loose. Slide the Stem [H] in-between the plates of the Shank [A] and align the holes vertically. [Fg. 5] Using the bottom vertically aligned hole.
- Page 4 STEP 6: Using one (1) Wing [P], slide both foam [Fg. 10] [Fg. 11] [Fg. 12] bumpers to the center of the Wing. Turn the handles on each Cradle Housing O] to loosen their grip. Slide two (2) Cradle Housings [O] above the foam bumpers and two (2) more Cradle Housings below the foam bumpers.
- Page 5 STEP 8: Slide the round end of one (1) Rubber Strap [S] onto each Upper Wheel Cradle [Q] and Lower Wheel Cradle [R]. [Fg. 13] NOTE: Be sure to slide the Rubber Straps [S] all the way onto the cradles so that it tightly rests over the plastic coating of the Wheel Cradle [Q &...
- Page 6 Operation: Bicycle Mounting Hang bicycles by the tires on the Upper Wheel Cradles [Q] with the chain rings to the outside. [Fg. 18 & 19] Adjust the Foam Bumpers located on the Wings [H] to protect the frame of the bicycle. IMPORTANT: For two bicycles, position the bicycles facing in opposite directions (front-to-back/back-to-front) with the chain ring to the outside.
- Page 7 Slide the Lower Wheel Cradle [R] to meet the bottom/side of the bicycle tire. Secure the Lower Wheel Cradle [R] using the same technique as the Upper Wheel Cradles. [Fg. 22 & 23] TIP: Pull the Rubber Straps [M] to the outside edge of the outer edge Lower Cradle [R] to position bicycles wheels so the frame...
- Page 8 OPERATION: TILT For loading and rear hatch access the BikeWing-2’s V-Base can be tilted to a ~50° angle. VEHICLE MUST BE STATIONARY WHILE THE RACK IS TILTED - NOT FOR USE IN TRANSIT. Begin by removing the Tilt Pin and Retainer Clip [Q] from the upper hole of the Tilt Bracket located on the Shank [A].
- Page 9 CAUTION: Car vehicle exhaust can cause a hazard. As a precaution, position bicycles clear of exhaust. LET’S GO AERO LIMITED LIFETIME WARRANTY If a Let’s Go Aero bike rack is found to have a defect in workmanship or material over the lifetime of the original purchaser, Let’s Go Aero will repair or replace the defect free of charge.
Need help?
Do you have a question about the BikeWing-2 and is the answer not in the manual?
Questions and answers