EGR RollTrac Owner's Manual
Electric roll cover
Hide thumbs
Also See for RollTrac:
- Installation manual ,
- Training manual (75 pages) ,
- Installation instructions manual (39 pages)
Related Manuals for EGR RollTrac
Summary of Contents for EGR RollTrac
- Page 1 id#117035 OWNER’S MANUAL IMPORTANT: PLACE IN THE CUSTOMER’S VEHICLE SERVICE BOOK ELECTRIC rt0001 RT0001 Date: 08/04/20 Issue: 5 Page: 1 of 12...
-
Page 2: Table Of Contents
SIDE RAIL Introduction. Thank you for purchasing this EGR RollTrac. Read this owner’s manual thoroughly before using this accessory and follow the instructions for use. This product must be installed exactly as specified in the installation instructions. Failure to do so may result in improper fit and/or retention and loss of warranty. -
Page 3: Warnings - Safety
Do not store or transport volatile materials, such as solvents, chemicals or liquids as fumes may accumulate inside tub. Do Not allow solvents, chemicals or oils to come in contact with the EGR Roll Trac. If this should occur clean the EGR RollTrac immediately with a mild detergent and water solution. -
Page 4: Maintenance
Disclaimer: In the event that your EGR RollTrac is found to be defective under the terms of this warranty, it is at the discretion of EGR to repair or replace the defective part. Transportation costs and fitment labour are not associated with this warranty claim. -
Page 5: Calibration Procedure
Calibration Procedure 1. Start the vehicle in an open area (note exhaust fumes are a health and safety hazard!). 2. Open the tailgate. 3. Ensure the motor clutch is engaged. 4. Ensure car doors are unlocked and disable auto-locking during calibration procedure. Press the two side rail buttons simultaneously for 10 seconds to START calibration mode. -
Page 6: Opening And Closing Procedure
OPEN PRESS ONCE UNLOCK 1. Press the “UNLOCK” button on the car remote. 2. Press the front button on the EGR RollTrac side rail as shown. Electric Closing Procedure: CLOSE PRESS ONCE 1. Press the rear button on the EGR RollTrac side rail as shown. -
Page 7: Locking Procedure
LOCK Emergency Opening: 1. In case of entrapment inside a locked vehicle tub fitted with EGR RollTrac, release the motor clutch by pushing in the Clutch Disengagement Lever (on the RH side of the cover). 2. Turn the emergency release handle located on the centre of the hand rail assembly and retract the slats manually. -
Page 8: Interior Light Operation
Interior Light: The interior light has 3 settings activated by pushing the button on the side. Each button press cycles from: 1. AUTO (default) which turns light off 2 mins after last button press. 2. ON - Light remains on for 20 mins 3. -
Page 9: Faqs
EGR have a range of service kits for interchangeable parts on EGR RollTrac. Do I need to drill holes in the vehicle body when installing EGR RollTrac? Whilst the EGR RollTrac fits to the vehicle using a clamp system, there is drilling required to fit the tailgate rail and drain tubes. -
Page 10: Trouble Shooting
Manually lock and unlock using the key, recheck operation. Remove power (fuse) and wait for 5 sec. before applying power back to RollTrac and recalibrate. Error mode is indicated by flashing LED lights and loss of function mid operation, follow steps as outlined above. - Page 11 If Roll Cover is operational - Check connections to LED light in side rail are pushed home. do not If EGR RollTrac is not operational – lighting is linked to installation of vehicle harness and connectors, switch troubleshoot and recheck operation.
-
Page 12: Installation Checklist
Position EGR RollTrac correctly relative to tailgate rail and cab Position EGR RollTrac on tub squarely and centrally Clamps are square and tight, torqued as specified in your EGR RollTrac installation instruction, side bolts and pads fitted. Check that the clutch release lever functions correctly (must be done prior to calibration)
Need help?
Do you have a question about the RollTrac and is the answer not in the manual?
Questions and answers