Table of Contents
Advertisement
Die/Kiss Cut
To perform die cut/kiss cut in one cutting line simultaneously
by designating the outline to green color RGB 255 and
defining the length and force setting on control panel (Please
refer to Chapter 4.9 for details).
Rear Paper
To detect if the rear paper sensor is covered to determine the
Sensor
following process; when it is enabled, the cutter will detect if
the material has covered the rear paper sensor under the Roll
and Edge mode; when disabled, the rear paper sensor will
not be functioning.
Note: Rear paper sensor only functions under "Roll" and
"Edge" mode.
DHCP
Shows your IP address for TCP/IP Configuration
IP Address
Shows the IP Address of your cutting plotter.
MAC Address
Shows the MAC Address of your cutting plotter.
Vacuum
To help improve tracking and cutting accuracy by turning on
the fans. If you turn off the vacuum system, the fans
will remain inactive during cutting or plotting.
First Back to
To enable the carriage back to the previous origin; when
"Enable" is selected, the carriage will not go back to the
Origin
previous origin, while the selection of "Disable" allows the
carriage to do so.
To enable the AAS copy. When "Enable" is selected, the AAS
AAS Copy
module will continue to read the registration mark to contour
cut. Users can set distance between images and AAS copy
times in this function. The range of distance is 0-500mm, and
the range of times is 0-1000.
AAS Offset
To set or modify AAS offset value.
You can refer to "5.3 Printer Test" for more details.
Paper Saving
To save media by four different modes:
Mode
1. Length expanded mode
3. Both expanded mode
Set
To build up the communication between host computer and
cutter.
Communication
Baud Rate is to determine the speed of data transmission.
Data Bits refers to the size of one block of data.
Parity is used to check if data was revived correctly or not.
9600, n, 7, 1, p
9600, o, 7, 1, p
9600, e, 7, 1, p
9600, n, 8, 1, p
9600, o, 8, 1, p
9600, e, 8, 1, p
19200, n, 7, 1, p
19200, o, 7, 1, p
19200, e, 7, 1, p
19200, n, 8, 1, p
19200, o, 8, 1, p
19200, e, 8, 1, p
Firmware
To display the version number of Firmware and FPGA code.
Version
Select
To select displayed languages on LCM panel in English,
Language
Spanish, Italian, Deutsch, Portuguese, Polish, Turkish or
French.
Select Units
Provide two-unit systems for users convenient.
The Control Panel
2. Width expanded mode
4. Both unexpanded mode
9600pbs, 7 Bits with NO Parity
9600pbs, 7 Bits with ODD Parity
9600pbs, 7 Bits with EVEN Parity
9600pbs, 8 Bits with NO Parity
9600pbs, 8 Bits with ODD Parity
9600pbs, 8 Bits with EVEN Parity
19200pbs, 7 Bits with NO Parity
19200pbs, 7 Bits with ODD Parity
19200pbs, 7 Bits with EVEN Parity
19200pbs, 8 Bits with NO Parity
19200pbs, 8 Bits with ODD Parity
19200pbs, 8 Bits with EVEN Parity
3-8
Jaguar V User Manual
Length: 0.2 ~9mm
Force: 45 g~ 450 g
Enable
Enable
Disable
Disable
Enable
Enable
Enable
Disable
Enable
Enable
Disable
Length
expanded
mode
English
cm/s; inch/oz;
Metric
cm/oz; inch/gram
Hide quick links:
Advertisement
Table of Contents
