Advertisement
Quick Links
Assembly & Installation Instructions:
Sierra 2-Leg Desk SEHX30-48-XXX-XX-X
Parts Included
A
Leg
Qty: 2
B
Short Bracket
Qty: 4
C
Left End Bracket
Qty: 1
D
Right End Bracket
Qty: 1
E
4 mm Allen Wrench
Qty: 1
F
#M6 × 14 mm Flat Head Cap
Screw
Qty: 20
Workrite Ergonomics | 800.959.9675 www.workriteergo.com
G
#12 × ¾" Pan Head Laminate
Top Screw
Qty: 22
H
Foot Glide
Qty: 4
I
Control Box
Qty: 1
J
#12 × 2" Flat Head Screw
Qty: 2
K
Cable Spool
Qty: 2
L
#8 × ⅝" Pan Head Screw
Qty: 12
M
3/ 1 6" Cable Loops
Qty: 10
N
Leg Cable, 1
meter
Qty: 2
O
Power Cord
Qty: 1
P
Style or Flat Foot Kit
Qty: 1
or
Q
Standard or
Programmable Switch
Qty: 1
or
Sold Separately:
Worksurface
1 of 9
Advertisement
Related Manuals for Workrite Ergonomics Sierra 2-Leg Desk SEHX30-48 Series
Summary of Contents for Workrite Ergonomics Sierra 2-Leg Desk SEHX30-48 Series
- Page 1 4 mm Allen Wrench #8 × ⅝" Pan Head Screw Qty: 1 Qty: 12 Sold Separately: #M6 × 14 mm Flat Head Cap 3/ 1 6" Cable Loops Worksurface Screw Qty: 10 Qty: 20 Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 9...
-
Page 2: Important Safety Instructions
Loading should be evenly distributed over table surfaces. “Payload Capacity” is the Workrite Ergonomics recommended maximum loading which includes the Workrite sourced worksurface. - Page 3 #M6 × 14 mm Flat Head Tighten securely. Cap Screw Caution! Only use the #M6 × 14 mm Flat Head Right Leg Cap Screw (F) for assembly. front Left Leg Right End Bracket Left End Bracket Workrite Ergonomics | 800.959.9675 www.workriteergo.com 3 of 9...
- Page 4 2.4 With frame set positioned and the four corner screws secure, drill all remaining pilot holes first then install all remaining #12×¾" Pan Head Laminate Top Screws (G). Do not drill all the way through worksurface! 3 screws per Short Bracket 2 screws per End Bracket (2 installed in Step 3.3) 4 of 9 Workrite Ergonomics | 800.959.9675 www.workriteergo.com...
- Page 5 Leave eight inches of slack to route cord. 5.2 Plug Power Cord (O) into power outlet AC on the bottom Control Box (I). 5.3 Lay the Control Box down in installation location with cables in place. Workrite Ergonomics | 800.959.9675 www.workriteergo.com 5 of 9...
- Page 6 6.4 Lay out Leg Cables (N) to be sure they reach from the Legs (A) to the Control Box (I). 48" Tables Hardware at actual size #12 × ¾" Pan Head Laminate Top Screw Hardware at actual size #12 × 2" Flat Head Screw 32" & 40" Tables 6 of 9 Workrite Ergonomics | 800.959.9675 www.workriteergo.com...
- Page 7 48" Tables #8 × ⅝" Pan Head Screw 32" & 40" Tables Note: For smaller work centers, it may be easier to wrap cable around Spools (K) prior to plugging into Legs (A). Workrite Ergonomics | 800.959.9675 www.workriteergo.com 7 of 9...
- Page 8 8.2 Insert the Switch Cable into port “A1” on the Control Box (I). Right Leg Cable (N) into Port “1” Power Cord (O ) in Port “AC” Switch Cable into Port “A1” Left Leg Cable (N) into Port “2” 8 of 9 Workrite Ergonomics | 800.959.9675 www.workriteergo.com...
- Page 9 Suggested cleaners: Windex or Formula 409. Do not use solvents and do not saturate or spray cleaners directly onto work center base. ✓ Parts & Accessories Visit http://workriteergo.com/documentation/other/workrite_ergonomics_pricing_specification_guide.pdf replacement parts. Workrite Ergonomics | 800.959.9675 www.workriteergo.com 9 of 9 #1500354 Rev C...
Need help?
Do you have a question about the Sierra 2-Leg Desk SEHX30-48 Series and is the answer not in the manual?
Questions and answers