Workrite Ergonomics Sierra SEHX7890-4272OC Series Assembly/Installation Instructions
3-leg desk
Hide thumbs
Also See for Sierra SEHX7890-4272OC Series:
- Assembly/installation instructions (11 pages)
Advertisement
Quick Links
Assembly & Installation Instructions:
Sierra 3-Leg Desk SEHX7890-4272OC-XXX-XX-X
Parts Included, Frame Set
A
Leg
Qty: 3
B
Rear Bracket
Qty:3
C
Connector Bracket
Qty: 2
D
#M6 × 14 mm Flat Head
Cap Screw
Qty: 36
E
Short Bracket
Qty: 3
F
Left End Bracket
Qty: 1
G
Right End Bracket
Qty: 1
H
Corner End Bracket
Qty: 1
I
#8 × ⅝" Pan Head Screw
Qty: 18
Workrite Ergonomics | (800) 959–9675 www.workriteergo.com
J
4 mm Allen Wrench
Qty: 1
K
#12 × ¾" Pan Head
Laminate Top Screw
Qty: 61
L
Corner Foot
0.4126 "
0.134"
3/4"
Qty: 1
0.216"
#12 Screw Size
#3 Drive
M
Foot Glides
Qty: 4
N
#12 x 2" Flat Head Screw
Qty: 2
O
Control Box
Qty: 1
P
Cable Spool
Qty: 3
Q
³⁄ 1 6" Cable Loops
Qty: 15
R
Leg Cable, 1 Meter
Qty: 2
S
Leg Cable, 2 Meters
Qty: 1
T
Power Cord
Qty: 1
U
Style or Flat Foot Kit
Qty: 1
or
V
Standard or
Programmable Switch
Qty: 1
or
W
Glide Adjuster Center Foot
Qty: 4
X
#M6 × 12 mm Flat Head Cap
Screw
Qty: 16
Sold separately: Worksurface
1 of 12
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Workrite Ergonomics Sierra SEHX7890-4272OC Series
Summary of Contents for Workrite Ergonomics Sierra SEHX7890-4272OC Series
- Page 1 Corner End Bracket #M6 × 12 mm Flat Head Cap Qty: 1 Screw Qty: 16 #8 × ⅝" Pan Head Screw ³⁄ 1 6" Cable Loops Qty: 18 Qty: 15 Sold separately: Worksurface Workrite Ergonomics | (800) 959–9675 www.workriteergo.com 1 of 12...
-
Page 2: Important Note
Loading should be evenly distributed over table surfaces. “Payload Capacity” is the Workrite Ergonomics recommended maximum loading which includes the Workrite sourced worksurface. - Page 3 96" W × 29" D 67" Use with 84" W × 23" D or 90" W × 29" D Use with 78" W × 23" D or 84" W × 29" D Workrite Ergonomics | (800) 959–9675 www.workriteergo.com 3 of 12...
- Page 4 Head Cap Screw (X) for assembly. Note: Brackets can be sized in 3" increments for any When shown upside down, right will be on your left and vice-versa. Your frameset may differ. non-Workrite top. 4 of 12 Workrite Ergonomics | (800) 959–9675 www.workriteergo.com...
- Page 5 Right End Bracket Note: The Right End Bracket (G) will be on Left configuration your left when upside down. Note: Left configurations will assemble as a mirror image of these instructions. Workrite Ergonomics | (800) 959–9675 www.workriteergo.com 5 of 12...
- Page 6 Note: Avoid trip or tip hazards! For uniquely shaped, non-standard worksurfaces, it is the installers responsibility to position the worksurface to minimize extended overhangs and position feet fully under the worksurface. 6 of 12 Workrite Ergonomics | (800) 959–9675 www.workriteergo.com...
- Page 7 #M6 × 14 mm Flat Head Cap Screw Note! Only use the #M6 × 14 mm Flat Head Cap Screw (D) supplied with Corner Flat Foot shown Foot and Foot Kit for assembly. Workrite Ergonomics | (800) 959–9675 www.workriteergo.com 7 of 12...
- Page 8 Control Box (O). 8" 8.4 Plug Leg Cable (R) into port “3” on the Control Box. 8.5 Lay the Control Box down in installation bottom location with cables in place. 8" 8" 8 of 12 Workrite Ergonomics | (800) 959–9675 www.workriteergo.com...
- Page 9 9.4 Lay out Leg Cables (R & S) to be sure they all reach the Control Box. Hardware at actual size Hardware at actual size #12 × 2" Flat Head Screw #12 × ¾" Pan Head Laminate Top Screw Workrite Ergonomics | (800) 959–9675 www.workriteergo.com 9 of 12...
- Page 10 Note the additional P-Loop and Cable Spool locations that may provide better attachment and routing options for your specific configuration. Hardware at actual size #8 × ⅝" Pan Head Screw 10.2 10.2 10.1 10.1 Switch Cable 10 of 12 Workrite Ergonomics | (800) 959–9675 www.workriteergo.com...
- Page 11 11.3 Connect 2 Meter Leg Cable (S) to the port on the Left Leg (A) then to port “2” on the Control Box (O) 11.3 11.1 Installed in Step 9 Installed in Step 9 11.1 11.3 Switch Cable into 11.2 Switch Port “A1" Workrite Ergonomics | (800) 959–9675 www.workriteergo.com 11 of 12...
-
Page 12: Cleaning Instructions
Suggested cleaners: Windex or Formula 409. Do not use solvents and do not saturate or spray cleaners directly to work center base. ✓ Replacement Parts Visit http://workriteergo.com/documentation/other/workrite_ergonomics_pricing_specification_guide.pdf replacement parts. #1500353 Rev B 12 of 12 Workrite Ergonomics | (800) 959–9675 www.workriteergo.com...
Need help?
Do you have a question about the Sierra SEHX7890-4272OC Series and is the answer not in the manual?
Questions and answers