Table of Contents
Advertisement
Chapter 5 Programming
5.7.3.2 Data Mode All
There are four Data Modes to choose from: Instantaneous, Average, Peak, and Valley. The Data Mode can
be applied to all points simultaneously (Data Mode All) or it can be set independently for each individual
point (Data Mode Indiv.).
To program a Data Mode for all points:
From the Record Modes Setup menu use the UP (↑ ↑ ↑ ↑ ↑ ) or DOWN (↓ ↓ ↓ ↓ ↓ ) button to highlight Data Mode All and
press the ENTER button. The current Data Mode will appear highlighted. To change the Data Mode, use
the UP (↑ ↑ ↑ ↑ ↑ ) or DOWN (↓ ↓ ↓ ↓ ↓ ) button to select Instantaneous, Average, Peak, or Valley as desired and press
the ENTER button to activate. Press the EXIT button to return to the Record Modes Setup menu.
5.7.3.2.1 Instantaneous
The Instantaneous mode stores only the latest sample to the disk/card and is used if you have one of the
special functions enabled, such as peak reading or moving average that does not need to be averaged.
5.7.3.2.2 Average
The Average mode will average all input data sampled at 8 times per second to the Record rate being
recorded. Thus, if data is being stored to disk/card once every minute (60 seconds), 480 samples will
be averaged.
5.7.3.2.3 Peak
Peak mode will record the peak or maximum value within the selected Record rate.
5.7.3.2.4 Valley
Valley mode will record the valley or minimum value within the selected Record rate.
5.7.3.3 Data Mode Indiv.
The user has the option to set the Data Mode for each channel individually.
To program a Data Mode individually for each point:
From the Record Modes Setup menu use the UP (↑ ↑ ↑ ↑ ↑ ) or DOWN (↓ ↓ ↓ ↓ ↓ ) button to highlight Data Mode Indiv. and
press the ENTER button. You will be prompted with "point? X". Use the keypad to select relevant point and
press the ENTER button. The current Data Mode will appear highlighted. To change the Data Mode, use
the UP (↑ ↑ ↑ ↑ ↑ ) or DOWN (↓ ↓ ↓ ↓ ↓ ) button to select Instantaneous, Average, Peak, or Valley as desired and press
the ENTER button to activate. Press the EXIT button to return to the Record Modes Setup menu. Repeat
this process for each point you want to set.
5.7.4 Points
The user may select which of the fifteen available points are to be recorded to disk/card. Any or all points may be
recorded, however the recording time available on the disk is divided among the number of points being recorded.
Ensure that points you do not wish to record, or that have no data attached, are not turned on to record.
To turn the points on or off:
From the Record Setup menu, use the UP (↑ ↑ ↑ ↑ ↑ ) or DOWN (↓ ↓ ↓ ↓ ↓ ) button to highlight Points press the ENTER button.
The display will read "point 1=yes" or "point 1=no". Use the UP (↑ ↑ ↑ ↑ ↑ ) or DOWN (↓ ↓ ↓ ↓ ↓ ) button to select the point you
wish to turn on or off. Press the YES button to record the point or the NO button to turn the point off and not
record. The next point will then be displayed. Once all points have been set to yes or no, press the ENTER
button to return to the Record Setup menu.
Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com
Page 5-33
Advertisement
Chapters
Table of Contents
