Angled base - full ends, straight base cutaway ends, modified base cutaway ends, straight base with full ends, storage
unit at rear, straight base - full ends, angled base - full ends, metal end panel with sink, rear sliding doors - plexi plenum, with pat (44 pages)
Summary of Contents for Structural Concepts Impulse Series
Page 1
READ AND SAVE THESE INSTRUCTIONS OPERATING MANUAL SELF-SERVICE COUNTERTOP UNITS SCC P/N >> MODELS CSC3223 / CSC3223.4254 / CSC3223.4817 99425 Note: See P/N 20-16813 For Field Service Parts List 888 E. Porter Road ∙ Muskegon, MI 49441 Phone: 231.798.8888 Fax: 231.798.4960 www.structuralconcepts.com Oper Manuals\Impulse\CSC3223_CSC3223-4254_CSC3223-4817_99425.pub Rev i Date: 8.27.2019...
This unit is designed for the display of products in ambient store conditions where temperatures and The Structural Concepts non-refrigerated service humidity are maintained at a maximum of 75° F cases are designed to merchandise unpackaged and 55% relative humidity.
INSTALLATION 1. Remove Unit From Skid Position the unit near a suitable electrical outlet. Caution: Case must always remain supported or center of gravity will allow case to fall. Slide unit to rear of skid and tip backward off skid. 2.
START-UP AND OPERATION For your safety, equipment is furnished with a properly grounded cord connector. Do not attempt to defeat the grounded connector. Light Switch 1. Set-up Counter Top Unit Remove case from skid and place on counter in the position at which the case will reside.
MAINTENANCE FUNDAMENTALS: SHELF ASSEMBLY REMOVAL / DECKING REMOVAL 1. Shelf Assembly Removal Remove brackets. Note: It may be necessary to remove the nylon shipping bracket retainers. Shelves can be removed for repositioning, Pliers will be required to accomplish this task. removal (for individual merchandising requirements) and cleaning.
MAINTENANCE FUNDAMENTALS: STANDARD DOOR MECHANISM / RYOBI DOOR MECHANISM 1. Door “Hold Open” Feature To reposition the shelving or restock the shelves, it is first helpful to use the door ‘hold open” feature. Open the door all the way (See light fixture). ...
Attach magnetic mounting clips onto LED light. LED lights rarely require change-out. Adjust magnetic mounting clips so they are equally Contact Structural Concepts’ Technical Service spaced on LED light. Department for replacement LED lights. Reattach LED light assembly to its shelf/header. ...
For additional technical information and service, see the TECHNICAL SERVICE page in this manual for instructions on contacting Structural Concepts’ Technical Service Department. See images below for samples of both refrigerated and non-refrigerated serial labels. ...
TROUBLESHOOTING / CLEANING SCHEDULE Troubleshooting Issue Resolution Case Lights Not Working Check LED lights for proper installation and connection. See LIGHT FIXTURES - LED section in manual for illustrations. Check for burned out LED lights. System is not Operating Confirm the utility power is on. Check the circuit breaker box for tripped circuits.
ILLUSTRATED PARTS BREAKDOWN (STANDARD CASE ONLY) Note: Depending Upon Features And Options Chosen, Above Illustration May Not Exactly Reflect Your Particular Case.
ILLUSTRATED PARTS BREAKDOWN (GENERAL) Note: Depending Upon Features And Options Chosen, Above Illustration May Not Exactly Reflect Your Particular Case.
PARTS LIST Sign Upright Tube LED Driver Acrylic Sign Side Deck Shelf Assembly Shelf Support Front Tissue Holder Shelf Support Rear Front Panel or Storage Door Shelf Bracket Acrylic End Glass LED Light Top Glass Light clip Acrylic Sign Door Assembly Single Pole Switch Shelf Assembly Note: Depending Upon Features And...
DAMAGE, STORE’S AMBIENT CONDITIONS, ETC.) LIMITED WARRANTY Overview: All sales by Structural Concepts Corporation (hereafter referred to as “SCC”) are subject to the following limited warranty. “Goods” refers to the product or products being sold by SCC. Warranty Scope: Warranty is for equipment sold in the United States, Canada, Mexico and Puerto Rico. Equipment sold elsewhere may carry modified warranties.
Need help?
Do you have a question about the Impulse Series and is the answer not in the manual?
Questions and answers