1. Manuals
  2. Brands
  3. H-KING Manuals
  4. Toy
  5. P 15B Mustang Berlin Express
  6. Instruction manual

H-KING P 15B Mustang Berlin Express Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL

Advertisement

Table of Contents
loading

Related Manuals for H-KING P 15B Mustang Berlin Express

Summary of Contents for H-KING P 15B Mustang Berlin Express

  • Page 1 INSTRUCTION MANUAL...
  • Page 2 46 Class 70 Class Or Electric equivalent (4T Engine) (2T Engine) AN ALL BALSA AND PLYWOOD CONSTRUCTED MODEL THAT IS ALMOST READY TO FLY This H-King version includes a pair of servoless retracts with scale oleo's SPECIFICATIONS Wingspan 1580mm Length 1180mm...
  • Page 3 This plane is guaranteed to be free from defects of materials and workmanship at the date of purchase. It does not cover any damage caused by use or modification. The warranty does not extend beyond the product itself and is limited only to the original cost. With the act of using and controlling this product the user accepts all liability for any damage caused with the final product.
  • Page 4 REQUIRED FOR OPERATION (Purchase separately) 2 x extension leads 10.5x6 for .40 - 2 cycle engine for the aileron 11x6 for .46 - 2 cycle engine servos. 1 x 12x6 for .60 - 4 cycle engine extension if doing 12x7 for .70 - 4 cycle engine the I.C.
  • Page 5 1 - Wing Servos WING - BOTTOM VIEW Adhesive tape -Switch on the radio (trims centered) then mount the servo horns in the 1-Cut away the covering on the bottom of one wing t neutral position as shown. where the aileron and flap servos go. -The servo horn should be 2-Connect the servo leads to the aileron and flap extension leads.

  • Page 6: Joining The Wing

    IMPORTANT: Please do not clean off the excess epoxy on the wing with a strong solvent or pure alcohol, only use kerosene otherwise you could take the color out of the covering. 6- RETRACT SERVO TRAY Retract servo tray Note: The H-King version is supplied with servoless Retract servo mount...

  • Page 7: Air Scoop

    13 - AIR SCOOP BOTTOM VIEW 6x40mm nylon bolt 15/32” Plastic air scoop 12mm ..2 Wing fairing Cut away the covering inside the line before installing the air scoop and wing cover 1- Using the ABS air scoop as a template, draw around the outside edge with a pencil and then remove it. 2- Using a sharp hobby knife cut away the covering just inside the line, please do not cut into the wood.

  • Page 8: Engine Mount

    17- ENGINE MOUNT 5/32x1” 1/8x5-1/64” 4x25mm screw 3x20mm screw Remove the magnetic ...4 ...4 hatch cover from the fuselage. Blind-nut 1/8”(3mm) nut ! Note, the engine side thrust is built into the firewall ....4 ....4 ! Align the mark on both mounts with the mark on the fuselage B’...

  • Page 9: Electric Motor

    18- FUEL TANK Blow To muffler Water Filler tube Rubber stopper 3x25mm screw To engine 3x35 mm screw Assemble the stopper and tubes as shown above. Insert the assembly clunk end first Check the tank for leaks - block the vents and into the fuel tank and firmly press the stopper into the neck of the tank.

  • Page 10: Horizontal Stabilizer

    20- HORIZONTAL STABILIZER Ensure the horizontal stabilizer is securely glued into place as a failure of this assembly will result in a crash. Cut away only the covering on both the right and lefthand side B’ Cut away the covering on both the top and bottom of the stabilizer A = A’...
  • Page 11 22- ELEVATOR Please ensure the hinges are securely glued into place, any failure will cause a crash. 3/8 in. (9.5mm) Apply a thin layer of machine oil or petroleum jelly to only the pivot point of the hinges on one elevator. Then push the elevator and its hinges into the hinge slots in the trailing edge of the horizontal stabilizer.
  • Page 12 24- SERVOS AND RX BATTERY BOTTOM VIEW Install the rudder, elevator and Tail wheel push rod throttle servos and Rx switch if Rudder push rod using either 2T or 4T engine. Battery area (if using a 2T engine) 4-49/64” (120mm) 2-61/64”...

  • Page 13: Center Of Gravity

    26- COWLING 1/16” 3/32x25/64” self tapping screw 1~2mm 2.5x10mm ....4 1- Attach a piece of transparent plastic to the side of the fuselage with Adhesive adhesive tape as shown. Transparent tape 2- Use a pencil or felt tipped pen to draw around the engine head plastic where it will exit the cowl.
  • Page 14 29- DECALS Decal 1- Cut out the decals and apply them to the positions shown. 2- Do not peel the backing paper off all at once. Peel off one corner of the backing and remove with scissors. 3- Place the decal in the correct position on the model and when with this position firmly press the corner without backing into place.
  • Page 15 Safety Precautions: 1. If you have the simulator, we suggest that you can practice your skill using the simulator before you fly this model, this will help when you come to fly the P51 for the first time. 2. Climb the plane out straight from the take-off area without turning to about 50 meters in height then throttle back to about 50-60% power whilst you get used to the flying characteristics.

Table of Contents