Power Requirements - Christie HS Series Product Safety Manual

floor. In addition, horizontal clearance to the hazard
zone shall be a minimum 2.5 meters.
• EXTREME BRIGHTNESS! Do not place reflective
objects in the product light path.
The following diagram shows the zones for optical and
skin hazard distances:
• A—Hazard zone. The region of space where the
projection light from the laser-illuminated projector
is above emission limits for Risk Group 2. The light
intensity may cause eye damage after a
momentary or brief exposure (before a person can
avert his or her eyes away from the light source).
The light may cause skin burns to occur.
• B—Hazard distance. Operators must control access
to the beam within the hazard distance or install
the product preventing potential exposure of the
spectators' eyes from being in the hazard distance.
• C—No access zone. Horizontal clearance of the no
access zone must be a minimum of 2.5 meters.
• D—Vertical distance to hazard zone. The hazard
zone must be no lower than 3.0 meters above the
floor.
• E—Represents the top view of the projector.
• F—Represents the side view of the projector.
For information detailing the hazard distance for each
lens, refer to the HS Series 2K Installation and Setup
Guide (P/N: 020-001464-XX) or HS Series 2K User
Manual (P/N: 020-001466-XX) .
For Installations in the United States
The following must be in place for laser-illuminated
projector installations in the United States:
• Any human access horizontally to the hazard zone,
if applicable, must be restricted by barriers.
• Permanent show installations containing Risk Group
3 laser-illuminated projectors must meet the
following conditions:
• Installed by Christie or by Christie-authorized
and trained installers. Refer to the Laser
Illuminated Projector-Class 1 Risk Group 3
Installation training (Course code: CF-LIPI-01)
on the http://www.christieuniversity.com site.
• Performed according to instructions provided
by Christie.
• Ensure the projection system is securely
mounted or immobilized to prevent unintended
movement or misalignment of the projections.
HS Series 2K Product Safety Guide—D13HD2-HS, D13WU2-HS, D16HD-HS, D16WU-HS, D20HD-HS, D20WU-HS
020-001465-03 Rev. 1 (09-2019)
Copyright © 2019 Christie Digital Systems USA Inc. All rights reserved.
Important Safety Information
• Temporary show installations containing Risk Group
3 laser-illuminated projectors may be installed by
Christie or sold or leased only to valid laser light
show variance holders (laser light show
manufacturers) for image projection applications.
Such manufacturers may currently hold a valid
variance for production of Class IIIb and IV laser
light shows and/or for incorporation of the Risk
Group 3 laser-illuminated projectors into their
shows. This requirement applies also to dealers and
distributors of these laser-illuminated projectors.
• The Christie Laser Projection System (Enterprise)
Installation Checklist must be fully completed after
the installation and sent to lasercompli-
ance@christiedigital.com. A copy can remain on-
site. This checklist can be found as a separate
document in the accessory box with the manual.
• Certain US states have additional laser regulatory
requirements. Go to www.christiedigital.com for
further information.

Power requirements

Learn about the power requirements for HS Series 2K
projectors.
D13WU2-HS/D13HD2-HS
Parameter Requirement
Power rating 120 - 240 VAC, 50/60 Hz, 12 A
200 - 240 VAC, 50/60 Hz, 7 A
(rated for China, India, Taiwan,
and Korea)
100 VAC, 50/60 Hz, 13 A, 1200W
(rated for Japan)
AC input coupler C14
Inrush current 80 A Maximum @240 VAC
Power consumption 1150 W Maximum
D16WU-HS/D16HD-HS
Parameter Requirement
Power rating 120 - 240 VAC, 50/60 Hz, 12 A
200 - 240 VAC, 50/60 Hz, 7 A
(rated for China, India, Taiwan,
and Korea)
200 VAC, 50/60 Hz, 7 A, 1250 W
(rated for Japan)
AC input coupler C14
Inrush current 80 A Maximum @240 VAC
Power consumption 1410 W Maximum
5