Page 1
BSS 2.0E Repair instructions C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 1 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 2
6. Disassembly 7. Assembly 8. Troubleshooting 9. Connection diagram C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 2 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 3
Order number BSS 2.0E 7 230 33 00 23 0 C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 3 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 4
Up-to-date test data for all models can be found on the FEIN Extranet (Customer Service → Repair Guides). Lubricants The lubricants and container sizes available from FEIN can be found on the FEIN Extranet (Customer Service → Repair Guides). Lists of spare parts Lists of spare parts and exploded views are available online at www.fein.com...
Page 5
Outside Germany, the regulations applicable in the relevant country must be observed! C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 5 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 6
Feeler gauge 0.1-0.15mm Pressure piece Ø 6.8mm; Ø 11mm C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 6 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 7
5. Lubricants and auxiliary substances required Lubricants Grease 0 40 101 0100 4 Gearbox C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 7 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 8
6. Remove electronics (5). 7. Disconnect the supply cable (6). C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 8 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 9
4. Remove the armature with intermediate flange (5). 5. Remove the air guide ring (6). C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 9 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 10
3. Drive field coil out of the motor housing by tapping it gently with the mallet. - Torx T15 - Plastic mallet C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 10 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 11
3. Disconnect the four cables (3) from the stator. C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 11 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 12
- 26mm, 19mm chuck cone - Drawing-off socket cap C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 12 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 13
- ø 4.5mm punch - Sleeve with ø18mm interior C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 13 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 14
5. Remove the set screws (6) on both sides. C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 14 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 15
2. Press the needle bearing (2) out of the housing. - Plastic mallet - Punch ø 2.8mm C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 15 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 16
4. Remove the cutter blades (4) with the compensating discs. C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 16 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 17
2. Remove two cutting jaws (2). - Torx T20 C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 17 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 18
- 3mm; 2.5mm hex key 3. Remove the hand guard (3). C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 18 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 19
5. Remove the grooved ball bearings (5) from the eccentric shaft together with the sleeve (6). C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 19 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 20
6. Press the gear-wheel (5) onto the eccentric shaft. C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 20 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 21
1. Secure the gear-wheel with the circlip (1). Tool: - Circlip pliers C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 21 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 22
4. Set the cutting jaw distance (1) to 5.3 mm using the set screw (4). 5. Tighten the cylinder head screw (5). C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 22 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 23
Replace the discs if necessary. 5. Insert the blade bolt (5). C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 23 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 24
3. Secure the blade bolts with the two circlips (2) on both sides. C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 24 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 25
4. Attach the adapter (3) to the housing and secure it with the three cylinder head screws (4). C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 25 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 26
- Assembly aid 6 41 22 108 00 0 C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 26 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 27
- Assembly aid 6 41 22 108 00 0 C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 27 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 28
3. Position the contact spring (3) in the motor housing. C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 28 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 29
Assemble the stator so that the identification number is located on the side of the slide switch. C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 29 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 30
4. Screw down the stator with the two screws (1) [1.8 ±0.1Nm]. Tool: - Torx T15 C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 30 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 31
3. Fasten the intermediate bearing with the four screws (3). C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 31 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 32
Connect the carbon brush and stator according to the connection diagram. C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 32 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 33
3. Screw down the fit strain relief (3) [0.6 ± 0.05Nm]. C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 33 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 34
2. Make sure the cable is not pinched! - Torx T15 C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 34 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 35
2. Fasten the housing with tool head using the two screws (2) [5 ±0.2Nm]. - 4mm hex key - Torx T15 C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 35 of 36 FEIN retains all rights of disposal, such as copying and circulation...
Page 36
BSS 2.0E 8. Connection diagram C-SC_CSSM Version 1.0 2013-07-18 All rights reserved by FEIN, especially in case of industrial rights registration. Page 36 of 36 FEIN retains all rights of disposal, such as copying and circulation...