1. Manuals
  2. Brands
  3. Roland Manuals
  4. Printer
  5. VersaUV LEC2-300
  6. Setup manual

Roland VersaUV LEC2-300 Setup Manual

Hide thumbs Also See for VersaUV LEC2-300:
Table of Contents

Advertisement

Quick Links

Download this manual
• Thank you very much for purchasing this product.
• To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read
through this manual completely and store it in a safe location.
• Unauthorized copying or transferal, in whole or in part, of this manual is prohibited.
• The specifications of this product and the contents of this operation manual are subject to change without notice.
• This manual and the product have been prepared and tested as much as possible. If you find any misprints or
errors, please inform Roland DG Corporation.
• Roland DG Corporation assumes no responsibility for any direct or indirect loss or damage that may occur through
use of this product, regardless of any failure to perform on the part of this product.
• Roland DG Corporation assumes no responsibility for any direct or indirect loss or damage that may occur with
respect to any article made using this product.
R2-191115T
Setup Guide

Advertisement

Table of Contents
loading

Related Manuals for Roland VersaUV LEC2-300

Summary of Contents for Roland VersaUV LEC2-300

  • Page 1 Roland DG Corporation. • Roland DG Corporation assumes no responsibility for any direct or indirect loss or damage that may occur through use of this product, regardless of any failure to perform on the part of this product.
  • Page 2 Operation of this equipment in a residential environment COMMISSION RADIO could cause radio interference. FREQUENCY INTERFERENCE For EU Countries STATEMENT Responsible Party : Roland DGA Corporation Address : 15363 Barranca Parkway Irvine, CA 92618 Manufacturer: U.S.A. ROLAND DG CORPORATION Telephone : 949-727-2100...

  • Page 3: Table Of Contents

    Installing the Ventilating Equipment ........................50 3. Appendix ........................53 Location of the Power Rating and Serial Number Label ....................54 Specifications ....................................55 Company names and product names are trademarks or registered trademarks of their respective holders. Copyright © 2019 Roland DG Corporation http://www.rolanddg.com/...
  • Page 4 For China 产品中有毒有害物质或元素的名称及含量 有毒有害物质或元素 部件名称 六价铬 多溴联苯 多溴二苯醚 铅(Pb) 汞(Hg) 镉(Cd) (Cr(Ⅵ)) (PBB) (PBDE) 印刷电路板 × ○ × ○ ○ ○ 头部 × ○ ○ ○ ○ ○ 壳体、底架 × ○ ○ ○ ○ ○ 电源 × ○ × ○ ○...

  • Page 5: To Ensure Safe Use

    To Ensure Safe Use Improper handling or operation of this machine may result in injury or damage to property. Points that must be observed to prevent such injury or damage are described as follows. About WARNING and CAUTION Notices Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly.
  • Page 6 To Ensure Safe Use This is a heavy machine. WARNING WARNING Unloading and emplacement are Be sure to lock the stand's casters. operations that must be performed by 6 If the machine should begin to topple, a persons or more. major accident may result, including crushing Tasks that require undue effort when of the parts of your body.
  • Page 7 If anything gets inside, immediately disconnect the power cord and contact your authorized Roland DG Corporation dealer. Never use the machine for any purpose for which it is not intended, or use the Never place any flammable object nearby.
  • Page 8 To Ensure Safe Use Important notes about the power cord, plug, and electrical outlet Never place any object on top or Never allow to get wet. Never bend or twist with excessive subject to damage. force. Never make hot. Never pull with excessive force. Dust may cause fire.
  • Page 9 To Ensure Safe Use Ink, cleaning liquid, and discharged fluid are flammable and toxic. WARNING WARNING Keep open flame away from the work Never drink or sniff ink, cleaning liquid, area. or discharged fluid, or allow them to Ink and discharged fluid are flammable. come in contact with the eyes or skin.
  • Page 10 To Ensure Safe Use This machine uses ultraviolet light CAUTION Never look at the blue-white (ultraviolet) light emitted from the print-head area for an extended time. Looking directly at the ultraviolet light from up close for an extended period may result in eye injury.
  • Page 11 To Ensure Safe Use Warning Labels Warning labels are affixed to the machine to make areas of danger immediately clear. The meanings of these labels are indicated below. Be sure to heed their warnings. Also, never remove the labels or allow them to become dirty. Caution: Ultraviolet Light When the cover is open, check that the UV lamp is off.

  • Page 12: Pour Utiliser En Toute Sécurité

    Pour utiliser en toute sécurité La manipulation ou l’utilisation inadéquate de cet appareil peuvent causer des blessures ou des dommages matériels. Les précautions à prendre pour prévenir les blessures ou les dommages sont décrites ci-dessous. À propos des avis ATTENTION et PRUDENCE Utilisé...
  • Page 13 Pour utiliser en toute sécurité Cet appareil est lourd. ATTENTION ATTENTION Le déchargement et la mise en place S’assurer de verrouiller les roulettes de la base. doivent être faits par au moins six Si éventuellement l’appareil commencerait à personnes. basculer, il pourrait provoquer un accident important, Les tâches qui exigent un effort trop grand si notamment écraser des parties de votre corps.
  • Page 14 électrique Ne jamais insérer d’objet étranger dans ou des blessures. Communiquer avec l’appareil. Ne jamais exposer l’appareil le représentant Roland DG Corporation aux déversements de liquides. autorisé. L’insertion d’objets comme des pièces de monnaie ou des allumettes ou le Ne pas utiliser le cordon électrique fourni...
  • Page 15 Pour utiliser en toute sécurité Remarques importantes à propos du câble d'alimentation, de la fiche et de la prise électrique. Ne jamais déposer aucun objet Ne jamais laisser mouiller. Ne jamais plier ni tordre avec une dessus au risque de les endommager. force excessive.
  • Page 16 Pour utiliser en toute sécurité L'encre, les liquides nettoyants et les liquides usés sont inflammables et toxiques. ATTENTION ATTENTION Ne pas approcher une flamme nue de Ne jamais boire l'encre, le liquide de l'espace de travail. nettoyage ni les liquides usés, ne pas en L'encre et les liquides usés sont respirer les vapeurs et ne pas laisser les inflammables.
  • Page 17 Pour utiliser en toute sécurité Cet appareil utilise des rayons ultraviolets PRUDENCE Ne jamais regarder pendant de longues périodes le rayonnement blanc bleuté (ultraviolet) émis par la tête d'impression. Le fait de regarder directement et de près le rayonnement ultraviolet pendant une période prolongée peut causer des lésions oculaires.
  • Page 18 Pour utiliser en toute sécurité Vignettes d’avertissement Des vignettes d’avertissement sont apposées pour qu’il soit facile de repérer les zones dangereuses. La signification des vignettes est donnée ci-dessous. Respecter les avertissements. Ne jamais retirer les vignettes et ne pas les laisser s’encrasser.

  • Page 19: Introduction

    1. Introduction 1. About the User's Manuals for This Machine ................18 2. Checking Included Items ......................19 1.Introduction...

  • Page 20: About The User's Manuals For This Machine

    1. About the User's Manuals for This Machine The following documentation is included with the machine. Paper Manuals • Setup Guide This manual contains details on how to install the machine and how to configure its initial settings. • Regular Maintenance Guide This manual contains details on the machine's daily maintenance as well as on the maintenance that must be performed periodically.

  • Page 21: Checking Included Items

    2. Checking Included Items The following items are included with the machine. Make sure they are all present and accounted for. Stand legs Power cord/power plug adapter Arms Casters (2) (1 each) (1 each for right and left) (1 each for right and left) Stand stay (1) Shafts (2) Shaft clamps (2)
  • Page 22 2. Checking Included Items Replacement wiper (1) Replacement felt wiper (1) Tweezers (1) Connection adapter (1) Setup Guide Regular Maintenance Cleaning liquid (1) Cleaning sticks (this document; 1) Guide (1) SOL INK cleaning cartridges Software RIP (1) Caster holders (4) 1.Introduction...

  • Page 23: Installation

    2. Installation 1. Checks before Installation ....................... 22 About Placement and Installation Work ..............22 Deciding On an Installation Site ..................22 Temperature and Humidity ....................23 Installation Space ......................... 23 Air Ventilation ........................23 2. Assembly and Ink Filling ......................24 Checks before Operations ....................

  • Page 24: Checks Before Installation

    1. Checks before Installation About Placement and Installation Work The placement and installation of this machine must be performed by suitably qualified workers. WARNING Entrust operations such as transportation, unloading, and emplacement to trained professionals. Suitable equipment and technical skills are required in handling the machine. Tasks that require undue effort may result in a major accident.

  • Page 25: Temperature And Humidity

    1. Checks before Installation Temperature and Humidity Maintain the specified temperature and humidity even when the machine is not in use. Failure to do so may result in malfunction. • During operation: Temperature: 15 to 32°C (59 to 90°F), humidity: 20 to 80%RH (no condensation) •...

  • Page 26: Assembly And Ink Filling

    2. Assembly and Ink Filling Checks before Operations Completed Drawing Necessary Tools (Included Items) • Hexagonal wrench (1) • Pipe (Use this when the hexagonal wrench is too short to easily tighten bolts) (1) • Bolts (40) • Washers (12) 2.Installation...

  • Page 27: Step 1: Assemble The Stand And Mount The Machine On The Stand

    2. Assembly and Ink Filling Step 1: Assemble the Stand and Mount the Machine on the Stand WARNING Perform this task with all power switches left switched off. Failure to observe this instruction may cause the machine to move suddenly, resulting in injury. CAUTION Unloading and emplacement are operations that must be performed by 6 persons or more.
  • Page 28 2. Assembly and Ink Filling Attach the casters onto the stand leg. Attach the casters so that they are a long distance from the stand stay. The casters have no particular front and rear orientation. Tighten the bolts securely (eight locations in total). Loose bolts may cause the stand to wobble. Bolt Tighten fully Pipe...
  • Page 29 2. Assembly and Ink Filling Place the machine on the stand. Align the holes on the bottom of the machine with the protrusions on the arms. Tighten the bolts securely (eight locations in total). Loose bolts may cause the stand to wobble. Tighten fully Bolts: 8 Washers: 8...

  • Page 30: Step 2: Attach The Media Holders

    2. Assembly and Ink Filling Step 2: Attach the Media Holders WARNING Perform this task with all power switches left switched off. Failure to observe this instruction may cause the machine to move suddenly, resulting in injury. Procedure Place the shafts on the stand. Pass the left media holder onto the shafts. Pass it through from the right edge as seen from the rear of the machine.
  • Page 31 2. Assembly and Ink Filling Lift up the front shaft and rear shaft at the same time. Pass the rear shaft through the media stays. Pass the rear shaft through the two media stays. Pass the right media holder onto the shafts, and then attach the retaining screw. It is sufficient to tighten the retaining screw lightly.

  • Page 32: Step 3: Install The Drain Bottle

    2. Assembly and Ink Filling Attach the shaft clamps to secure the shafts in place. To ensure the media holders do not get caught in the shaft clamps, do not place the media holders too close to the edges. Hexagonal Hexagonal wrench wrench...
  • Page 33 2. Assembly and Ink Filling Install the drain funnel. Screw the drain funnel all the way into the hole where the bottom plug was attached. IMPORTANT Use caution to turn the bottle without applying excessive force. Install the drain bottle stand. Insert the drain bottle stand into the groove on the bottom surface of the printer unit, and then shift the drain bottle stand to the left.
  • Page 34 2. Assembly and Ink Filling Install the drain bottle in the bottle stand. Insert the drain bottle to the back, as far as it will go. IMPORTANT: Leave the drain bottle attached at all times. Only remove the drain bottle when you are disposing of the discharged fluid. Unnecessarily removing the drain bottle may lead to the discharged fluid spilling.

  • Page 35: Step 4: Remove And Store The Retainers

    2. Assembly and Ink Filling Step 4: Remove and Store the Retainers IMPORTANT • Make sure to remove all the retainers. Any that remain may cause faulty operation or breakdown when the power is switched on. • Store the retainers because they are needed again when transporting the machine. Procedure Remove all the retainers indicated by A, B, and C.

  • Page 36: Step 5: Attach The Label

    2. Assembly and Ink Filling Step 5: Attach the Label This work is required when using the machine with four colors (CMYK). Items Used in this Procedure Cartridge-slot label (for four colors) Included items Step 6: Connect the Power Cord and the Cable Procedure Insert the cable clamp.
  • Page 37 2. Assembly and Ink Filling Cable clamp Pass the Ethernet cable and the power cord through here. Power cord Ethernet Cable (Category 5 or Ethernet higher) (100BASE-TX recommended) Fine-tune the orientation of the machine, and then adjust the stand casters. Face the casters to the front. Lock the casters. Use the caster holders to fix the casters in place. 2.Installation...

  • Page 38: Step 7: Set The Language And The Units

    2. Assembly and Ink Filling Step 7: Set the Language and the Units Procedure Close the front cover. Turn on the main power switch. Hold down [MENU] and press the sub power switch. Press [ ] or [ ] to select the language you want, and then press [ENTER]. MENU LANGUAGE ENGLISH Press [ ] or [ ] to select the unit of measurement you want (for length), and then press...

  • Page 39: Step 8: Fill The Machine With Ink

    Be careful not to insert the wrong cartridges. If you insert an incorrect cartridge by mistake, contact your authorized Roland DG Corporation dealer. • Be sure to insert cartridges horizontally. Otherwise, cleaning and filling may not be performed properly.
  • Page 40 2. Assembly and Ink Filling Select the ink type. Press [ ] or [ ] to select the ink type, and then press [ENTER]. SELECT INK TYPE SELECT INK TYPE ECO-UV4 4COLOR ECO-UV4 6COLOR Cyan (C) Magenta (M) Name to select White (W) Gloss (Gl) Yellow (Y)
  • Page 41 2. Assembly and Ink Filling When the following screen is displayed, remove the SOL INK cleaning cartridges whose slot numbers are flashing. REMOVE CL-LIQUID When the following screen is displayed, insert SOL INK cleaning cartridges into the slots whose numbers are flashing. The SOL INK cleaning cartridges are not differentiated by color. SET CL-LIQUID The screen shown below appears.
  • Page 42 2. Assembly and Ink Filling When the following screen is displayed, insert an ink cartridge for each color. SET CARTRIDGE 12345678 Insert the ink cartridge for each color. When ink cartridges are inserted in all the slots, the following screen appears. FILLING INK...

  • Page 43: Installing The Cutting Tool

    3. Installing the Cutting Tool CAUTION Be sure to perform operations as specified by the instructions, and never touch any area not specified in the instructions. Sudden movement of the machine may cause injury. CAUTION Never touch the tip of the blade. Doing so may result in injury. The cutting performance of the blade will also be impaired. Step 1: Assemble the Cutting Tool Required items Blade holder...

  • Page 44: Step 2: Install The Cutting Tool

    3. Installing the Cutting Tool Step 2: Install the Cutting Tool Enter the "REPLACE BLADE" menu. Press [MENU]. Press [ ] several times to display the screen shown below. MENU SUB MENU Press [ ] once, and then press [ ] several times to display the screen shown below. SUB MENU MAINTENANCE Press [ ] once, and then press [ ] several times to display the screen shown below.
  • Page 45 3. Installing the Cutting Tool Install the cutting tool in the cutting carriage. Not OK Tighten the screw. Close the front cover. Press [ENTER]. IMPORTANT: Handling the cutting carriage Leave the cutting-carriage screw loose when no cutting tool is installed. Keeping the screw firmly tightened causes the cutting tool insertion hole to become gradually smaller, making installation difficult.

  • Page 46: Network Settings

    4. Network Settings The examples used in the procedures for making the settings described in this section assume you are using one computer and one machine. The settings used in this section are merely example settings. The procedures and setting values described here may not be suitable for all operating environments. If the computer you're using is connected to a number of networked devices or to the Internet, incorrect settings may adversely affect the entire network.
  • Page 47 4. Network Settings Click [Properties]. The [Ethernet Properties] dialog box (or the [Local Area Connection Properties] dialog box on Windows 7) appears. If the [User Account Control] dialog box appears, click [Continue]. Select [Internet Protocol Version 4 (TCP/IPv4)], and then click [Properties]. If the [Internet Protocol] check box is clear, select it. The [Internet Protocol Version 4 (TCP/IPv4) Properties] dialog box appears.
  • Page 48 4. Network Settings Select [Use the following IP address]. Enter the information as shown below, and then click [OK]. Item Address to enter IP address 192.168.0.XXX Subnet mask 255.255.255.0 Here, "XXX" can be any number from 1 to 254. However, be sure to specify a number that is different from the numbers used for other computers and devices.

  • Page 49: Step 2: Make The Network Settings On The Printer

    4. Network Settings Step 2: Make the Network Settings on the Printer Set the IP address. Press [MENU]. Press [ ] several times to display the screen shown below. MENU SYSTEM INFO. Press [ ] once, and then press [ ] several times to display the screen shown below. SYSTEM INFO.
  • Page 50 4. Network Settings Set the subnet mask. Press [ ] to display the screen shown below. NETWORK SUBNET MASK Press [ ] twice to display the screen shown below. SUBNET MASK 000.000.000.000 Press [ ] or [ ] to select the address number. Press [ ].

  • Page 51: Step 3: Make The Port Settings For The Software Rip

    4. Network Settings Set the gateway address. Press [ ] to display the screen shown below. NETWORK GATEWAY ADDR. Press [ ] twice to display the screen shown below. GATEWAY ADDR. 000.000.000.000 Press [ ] or [ ] to select the address number. Press [ ].

  • Page 52: Installation Of Ventilating Equipment

    Ventilating Equipment In preparing ventilating devices, please note the following points. • You will be required to use the ventilating devices recommended by Roland DG Corporation. For the details of the recommended products, contact your authorized Roland DG Corporation dealer.
  • Page 53 5. Installation of Ventilating Equipment Attach the hose to the connection port on the machine. 2.Installation...
  • Page 54 5. Installation of Ventilating Equipment 2.Installation...

  • Page 55: Appendix

    3. Appendix Location of the Power Rating and Serial Number Label ............ 54 Specifications ............................. 55 3.Appendix...

  • Page 56: Location Of The Power Rating And Serial Number Label

    Location of the Power Rating and Serial Number Label Serial number This number is required when you seek maintenance, servicing, or support. Never peel off the label. Power rating Use an electrical outlet that meets the requirements for voltage, frequency, and amperage given here.

  • Page 57: Specifications

    Cutting speed 10 to 300 mm/s (0.4 to 11.8 in/s) Blade force (*3) 30 to 500 gf Type Roland CAMM-1 series blade Blade Offset 0.000 to 1.500 mm (0.0 to 59.1 mil) Software resolution (when cutting) 0.025 mm/step (0.98 mil/step) Distance accuracy (when printing) Error of less than ±0.3% of distance traveled or ±0.3 mm (±11.8 mil),...
  • Page 58 • 500 gf is the maximum instantaneous blade force. • The blade force must be adjusted according to details such as the media thickness. • Media type: Media specified by Roland DG Corporation • Temperature: 25°C (77°F), humidity: 50%RH • Roll media must be loaded correctly.

Table of Contents