Be sure to read this document before using the machine. Changes to the “Setup Guide” (“First Step Guide” for the LEF-12) Model Change LEC-300/300A/330/540, LEJ-640 Installing the Ink Cartridges STEP 5: Switch On/Make the initial settings LEF-12 STEP 6: Installing the Ink Cartridges Changes to the “User’s Manual”...
Page 2
• If you are already using the machine, check the firmware version. • For the method to follow in checking the firmware version, see the "User's Manual" (the "Master Guide" for the LEF-12). Model Firmware version Roland VersaWorks version LEC-300/300A/330/540 Ver. 6.30 or later LEJ-640 Ver.
Installing the Ink Cartridges Models : LEC-300/300A/330/540, LEJ-640 Articles in the Setup Guide * Pages in the First Step Guide for the LEF-12 Replace the information on the following articles of the table of contents with the information found in this document .
Page 7
Installing the Ink Cartridges <White mode> 3-1 . Hold down , switch on the main power switch . 3-2 . When the message shown below appears on the display screen, release the operation-panel buttons . SET INK MODE WHITE INK <Gloss/White mode>...
Page 8
Installing the Ink Cartridges <EUVS ink mode> 3-1 . Hold down , switch on the main power switch . 3-2 . When the message shown below appears on the display screen, release the operation-panel buttons . SET INK MODE ECO-UVS WW Hold down until the message appears .
Installing the Ink Cartridges Affixing the Cartridge-slot Labels * In the case of LEF-12, this operation is not required . Go on to “Installing the Ink Cartridges” (p . 8) Procedure Open the ink cartridge cover . Knob Hold the knob Affix the cartridge-slot labels (supplied parts) appropriate for the selected ink mode to the location shown in the figure .
Insert each color ink cartridge into the slot labeled with the matching color . If you insert the wrong cartridges, the color inks may be mixed . Be careful not to insert the wrong cartridges . Contact your authorized Roland DG Corp . dealer or us, if you inserted the wrong cartridges and the color inks were mixed .
Page 11
Installing the Ink Cartridges Press to select the unit of measurement you want (for length) . LENGTH UNIT Press to select the unit of measurement you want (for temperature) . TEMP. UNIT Press 2. Clean the print heads using the SOL INK cleaning cartridge (LEC- 330/540,LEJ-640) * In the case of LEF-12, go on to “2 .Clean the print heads using the SOL INK cleaning cartridge (LEF-12)”...
Page 12
Installing the Ink Cartridges Press Make sure the drain bottle is installed . INSTALL DRAIN BOTTLE Press Insert the SOL INK cleaning cartridges into slots 1, 2, 3, and 4 . SET CL-LIQUID 1 2 3 4 FILLING INK... >> When this screen appears, pull out the SOL INK cleaning cartridges .
Page 13
Installing the Ink Cartridges When this screen appears, make sure the drain bottle is installed, and press CHECK DRAIN BOTTLE Cleaning is finished . Go on to “3 . Insert the ink cartridges for the respective colors . ” (p . 12) 2.Clean the print heads using the SOL INK cleaning cartridge (LEF-12) Press to select the ink type .
Page 14
Installing the Ink Cartridges When this screen appears, pull out the dummy cartridges, and press REMOVE DUMMY CRT. SLOT: 3,4 SET CL-LIQUID When a new slot number is displayed, repeat the procedure from Steps 3to 6 using the cleaning cartridge you just pulled out .
Page 15
Installing the Ink Cartridges Insert the ink cartridge for each color . SET CARTRIDGE 1 2 3 4 5 6 FILLING INK... >>>>>>>>>> Insert into the slot of the matching color . * This figure indicates LEC-330 . LEC-330/540,LEJ-640 Ink mode Ink cartridges 1 cartridge each of cyan, magenta, yellow, and black Gloss mode...
Page 16
Installing the Ink Cartridges Make sure the drain bottle is installed, and press CHECK DRAIN BOTTLE When this screen appears, filling with ink is finished . SETUP SHEET ROLL Be Sure to Keep the Ink Cartridge Cover Closed at All Times. The ink cartridge cover prevents the ink cartridges from being exposed to direct sunlight or strong illumination .
Correcting for Misalignment in Bidirectional Printing Performing the Initial Adjustment (Correcting for Misalignment in Bidirectional Printing More Precisely) Models : LEC-300/300A/330/540, LEJ-640 Articles in the User’s Manual * Replace the information on the following articles of the table of contents with the information found in this document .
Page 19
Press to display the figure on the below . DETAIL SETTING SETTING NO.1 Press 2. Enter the adjustment value. Press to select one from H1 to H6 (from H1 to H3 for the LEC-300/300A) 2. Changes to the User’s Manual...
Page 20
You may not be able to see “H5” or “H6” (“H3” for the LEC-300/300A) when using certain media, such as white media with no luster . In this case, set “H5” and “H6” (“H3” for the LEC-300/300A) to the same value as “H4” (“H2”...
Correcting for Misalignment in Bidirectional Printing Corrections Performed from the [MEDIA SETTING] Menu Models : LEC-540, LEJ-640 Articles in the User’s Manual * This section only discusses the procedure for setting [ADJUST BI-DIR] on the [MEDIA SETTING] menu . For other setting items, follow the instructions in the User’s Manual .
Correcting for Misalignment in Bidirectional Printing Models : LEC-300/300A/330/540, LEJ-640 Articles in the User’s Manual * Replace the information on the following articles of the table of contents with the information found in this document .
Page 23
"Bidirectional Correction . " This misalignment varies according to the print-head height and the thickness of the media, so we recommend performing correction to match the media you're using . LEC-300/300A/330/540 This settings also serves to correct for misalignment of the printing and cutting positions . In such cases, check or adjust this setting .
Switching the Ink Type Models : LEC-300/300A/330/540, LEJ-640 Articles in the User’s Manual * Master Guide for the LEF-12 * Replace the information on the following articles of the table of contents with the information found in this document .
Insert each color ink cartridge into the slot labeled with the matching color . If you insert the wrong cartridges, the color inks may be mixed . Be careful not to insert the wrong cartridges . Contact your authorized Roland DG Corp . dealer or us, if you inserted the wrong cartridges and the color inks were mixed .
Page 26
Switching the Ink Type 2. Fill with ink Press the sub power button . Select the ink type . <When switching to EUV ink> 2-1 . Press to select “ECO-UV . ” SELECT INK TYPE ECO UV CMYKGlW 2-2 . Press <When switching to EUV3 ink>...
Page 27
• ”Making the Settings for Roland@NET” in ”Roland VersaWorks Quick Start Guide” MEMO • When you initialize the application, the settings of Roland@NET are initialized as well . Please make the settings again . 2. Changes to the User’s Manual...
To Customers Who Upgraded the Firmware of the Machine Precautions Regarding Saved Settings Model Firmware version LEC-300/300A/330/540 Ver . 6 . 3 0 or later LEJ-640 Ver . 2 . 1 0 or later LEF-12 Ver . 2 . 1 0 or later If you upgrade the firmware of your machine to the above versions or higher, the bidirectional printing adjustment specifications will be changed .
About Handling of EUVS/EUV3 Ink Handling of the EUVS ink and EUV3 ink are the same as that of the EUV ink . Please read ”Setup Guide” and ”User’s Manual . ” 3. Supplemental...