Fujitsu PRIMERGY TX1310 M3 Upgrade And Maintenance Manual
  1. Manuals
  2. Brands
  3. Fujitsu Manuals
  4. Server
  5. PRIMERGY TX1310 M3
  6. Upgrade and maintenance manual

Fujitsu PRIMERGY TX1310 M3 Upgrade And Maintenance Manual

Hide thumbs Also See for PRIMERGY TX1310 M3:
Table of Contents

Advertisement

Quick Links

Download this manual
Upgrade and Maintenance Manual - English
FUJITSU Server PRIMERGY TX1310 M3
Upgrade and Maintenance Manual
January 2018

Advertisement

Table of Contents
loading

Related Manuals for Fujitsu PRIMERGY TX1310 M3

Summary of Contents for Fujitsu PRIMERGY TX1310 M3

  • Page 1 Upgrade and Maintenance Manual - English FUJITSU Server PRIMERGY TX1310 M3 Upgrade and Maintenance Manual January 2018...
  • Page 2 – The contents of this manual may be revised without prior notice. – Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual. – No part of this manual may be reproduced in any form without the prior written permission of Fujitsu.
  • Page 3 Before reading this manual For your safety This manual contains important information for safely and correctly using this product. Carefully read the manual before using this product. Pay particular attention to the accompanying manual "Safety Notes and Regulations" and ensure these safety notes are understood before using the product.
  • Page 4 Please consult the sales staff of Fujitsu if intending to use this product for high safety use. Measures against momentary voltage drop This product may be affected by a momentary voltage drop in the power supply caused by lightning.
  • Page 5 Version history Version history Issue number Reason for update 1.0 / June 2017 Initial release 2.0 / June 2017 Gaskets for RDX drive added 3.0 / January 2018 Regular update Upgrade and Maintenance Manual TX1310 M3...
  • Page 6 Version history Upgrade and Maintenance Manual TX1310 M3...

  • Page 7: Table Of Contents

    Contents Introduction ......15 Notational conventions ....16 Before you start .
  • Page 8 Contents 4.5.2 Sliding the HDD cage into the chassis ....52 4.5.3 Installing the side cover ..... . 55 Connecting the power cord .
  • Page 9 Contents 6.2.1 Preliminary steps ......76 6.2.2 Removing the PSU ..... . . 76 6.2.3 Installing the PSU .
  • Page 10 Contents 8.3.4 Concluding steps ......106 Expansion cards and backup units ... . . 107 Basic information .
  • Page 11 Contents 10.4 Replacing memory modules ....128 10.4.1 Preliminary steps ......128 10.4.2 Removing the defective memory module .
  • Page 12 Contents 12.2.2.3 Concluding steps ..... . 161 12.2.3 Replacing an ODD ..... . . 161 12.2.3.1 Preliminary steps .
  • Page 13 Contents 14.3.4 Concluding steps ......180 System board and components ....181 15.1 Basic information .
  • Page 14 Contents 16.3.1.3 Installing the new system cable ....216 16.3.1.4 Concluding steps ..... . 216 16.3.2 Replacing the HDD cable (bottom HDD cage) .

  • Page 15: Introduction

    Introduction This Upgrade and Maintenance Manual provides instructions for the following procedures: Upgrading the server configuration by adding optional hardware ● components Upgrading the server configuration by replacing existing hardware ● components with superior ones. Replacing defective hardware components ● This manual focuses on on-site maintenance tasks.

  • Page 16: Notational Conventions

    Introduction Notational conventions The following notational conventions are used in this manual: indicates commands or menu items Text in italics indicates system output fixed font indicates text to be entered by the user semi-bold fixed font "Quotation marks" indicate names of chapters and terms that are being emphasized describes activities that must be performed in the order Ê...

  • Page 17: Before You Start

    Before you start Before you start any upgrade or maintenance task, please proceed as follows: Ê Carefully read the safety instructions in chapter "Important information" on page Ê Make sure that all necessary manuals are available. Refer to the documentation overview in section "Documents you need at hand"...
  • Page 18 For Japan: http://www.fujitsu.com/jp/products/computing/servers/primergy/ Please contact your local Fujitsu customer service partner for details on how to order expansion kits or spare parts. Use the Fujitsu Illustrated Spares Catalog to identify the required spare part and obtain technical data and order information.

  • Page 19: Classification Of Procedures

    At the beginning of each procedure, the involved unit type is indicated by one of the symbols introduced in this section. Please ask your local Fujitsu service center for more detailed information. 2.1.1 Customer Replaceable Units (CRU) Customer Replaceable Units (CRU) Customer Replaceable Units are intended for customer self service.

  • Page 20: Upgrade And Repair Units (Uru)

    (Repair Units). For Japan, customer allows only upgrade. For upgrade units as customer replaceable, please refer to: http://www.fujitsu.com/jp/products/computing/servers/primergy/ Server management error messages will report defective Upgrade and Repair Units. Upgrade and repair procedures involve shutting down and opening the server.

  • Page 21: Field Replaceable Units (Fru)

    Maintenance procedures involving Field Replaceable Units must be performed exclusively by Fujitsu service personnel or technicians trained by Fujitsu. Please note that unauthorized interference with the system will void the warranty and exempt the manufacturer from all liability. Components that are handled as Field Replaceable Units –...

  • Page 22: Average Task Duration

    Before you start Average task duration Hardware: 10 minutes The average task duration including preliminary and concluding steps is indicated at the beginning of each procedure next to the procedure class. Refer to the following table for an overview of steps taken into account for calculating the average task duration: Step included...

  • Page 23: Tools You Need At Hand

    Before you start Tools you need at hand When preparing the maintenance task, ensure that all required tools are available according to the overview below. You will find a list of required tools at the beginning of each procedure. List of used screws (not valid for Japan) Screw driver/ bit insert Screw...
  • Page 24 Before you start Screw driver/ bit insert Screw Usage Type Torque Phillips M2.5 x 4 mm PH1 / (+) No. 1 (silver) 0.4 Nm C26192-Y10-C103 Hexagon nut UNC #4-40 Serial 5 mm (silver) connector 0.6 Nm V26827-B408-V989 Table 2: List of used screws (not valid for Japan) List of used screws for Japan Screw driver/ bit insert...
  • Page 25 Before you start Screw driver/ bit insert Screw Usage Type Torque TPM bit insert Dedicated TPM REM 3 x 15 mm TPM screw screw driver / (black) One way TPM module head C26192-Y10-C176 fixing tool 0.6 Nm Phillips HDD cage M3 x 3.5 mm PH1 / (+) No.

  • Page 26: Documents You Need At Hand

    For Japan: http://www.fujitsu.com/jp/products/computing/servers/primergy/manual/ Document Description "Quick Start Hardware - Quick installation poster for initial operation, FUJITSU Server PRIMERGY available online TX1310 M3" leaflet "ServerView Quick Start Guide" Information on initial server setup and " ServerView クイックスタート software configuration, available online ガイド...
  • Page 27 Description Spare parts identification and information system (not valid for Japan), available for online use or download (Windows OS) at Illustrated Spares catalog http://manuals.ts.fujitsu.com/illustrated_spares or from the CSS component view of the ServerView Operations Manager. Glossary available online Important information on warranty "Warranty"...
  • Page 28 Before you start Upgrade and Maintenance Manual TX1310 M3...

  • Page 29: Important Information

    Important information Depending on your server or the installed options some information is not valid for your server. CAUTION! Before installing and starting up a server, please observe the safety instructions listed in the following section. This will help you to avoid making serious errors that could impair your health, damage the server and endanger the data base.
  • Page 30 Important information Before starting up During installation and before operating the server, observe the instructions ● on environmental conditions for your server. If the server is brought in from a cold environment, condensation may form ● both inside and on the outside of the server. Wait until the server has acclimatized to room temperature and is absolutely dry before starting it up.
  • Page 31 Important information Always connect the server and the attached peripheral devices to the same ● power circuit. Otherwise you run the risk of losing data if, for example, the server is still running but a peripheral device (e.g. memory subsystem) fails during a power outage.
  • Page 32 Important information The warranty is void if the server is damaged during installation or ● replacement of server expansions. Only set screen resolutions and refresh rates that are specified in the ● operating manual for the monitor. Otherwise, you may damage your monitor. If you are in any doubt, contact your sales outlet or customer service center.
  • Page 33 Important information The battery used in this server may present a fire or chemical burn hazard if ● mistreated. Do not disassemble, heat about 100 °C (212F), or incinerate the battery. Replace the lithium battery on the system board in accordance with the ●...
  • Page 34 Important information Do not pull on, press hard, or otherwise handle the CD/DVD/BD tray ● roughly. Do not disassemble the optical disk drive. ● Before use, clean the optical disk tray using a soft, dry cloth. ● As a precaution, remove disks from the optical disk drive when the ●...
  • Page 35 Important information You can prevent damage from the optical disk drive and the CDs/DVDs/BDs, as well as premature wear of the disks, by observing the following suggestions: – Only insert disks in the drive when needed and remove them after use.
  • Page 36 Important information The circuit boards and soldered parts of internal options are exposed and ● can be damaged by static electricity. To ensure reliable protection, you must wear an earthing band on your wrist when working with ESD modules and connect it to an unpainted, conducting metal part of the server.
  • Page 37 Important information When connecting and disconnecting cables, observe the relevant ● instructions in the "Important Information" chapter of the technical manual for the corresponding rack. The technical manual is supplied with the corresponding rack. When installing the rack, make sure that the anti-tilt mechanism is ●...

  • Page 38: Ce Conformity

    Important information CE conformity :The system complies with the requirements of European Regulations. Find the CE declaration on certificate portal: https://sp.ts.fujitsu.com/sites/certificates/default.aspx To open the CE declaration applicable for your system, proceed as follows: Ê Select Industry Standard Servers. Ê Select your model, e.g. Rack server.

  • Page 39: Fcc Class A Compliance Statement

    Consult the dealer or an experienced radio/TV technician for help. ● Fujitsu is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Fujitsu. The correction of interferences caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.

  • Page 40: Environmental Protection

    Important information Environmental protection Environmentally-friendly product design and development This product has been designed in accordance with the Fujitsu standard for "environmentally friendly product design and development". This means that key factors such as durability, selection and labeling of materials, emissions, packaging, ease of dismantling and recycling have been taken into account.
  • Page 41 Further information can be found at: http://ts.fujitsu.com/recycling Details regarding the return and recycling of devices and consumables within Europe can also be found in the "Returning used devices" manual, via your local Fujitsu branch, or at: http://ts.fujitsu.com/recycling Upgrade and Maintenance Manual TX1310 M3...
  • Page 42 Important information Upgrade and Maintenance Manual TX1310 M3...

  • Page 43: Basic Hardware Procedures

    Basic hardware procedures Using diagnostics information Use the Fujitsu ServerView Suite management software to plan the upgrade or replacement of hardware components. Please refer to the following ServerView Suite topics: – Operation – Maintenance It is recommended to prepare local maintenance tasks using remote diagnostics procedures, see "ServerView Suite Local Service Concept (LSC)"...

  • Page 44: Shutting Down The Server

    Basic hardware procedures Shutting down the server CAUTION! For further safety information, please refer to chapter "Important information" on page Ê Inform the system administrator that the server will be shut down and put offline. Ê Terminate all applications. Ê Perform the required procedures described in the preliminary steps of each upgrade or maintenance task.

  • Page 45: Disconnecting The Power Cord

    Basic hardware procedures Disconnecting the power cord Figure 3: Disconnecting the power cord Ê Disconnect the power cord from the PSU. Upgrade and Maintenance Manual TX1310 M3...

  • Page 46: Getting Access To The Component

    Basic hardware procedures Getting access to the component CAUTION! Before removing or installing covers, turn off the server and all ● peripheral devices. Also unplug all power cables from the outlet. Failure to do so can cause electric shock. In order to comply with applicable EMC regulations (regulations on ●...

  • Page 47: Extending The Hdd Cage Out Of The Chassis

    Basic hardware procedures 4.4.2 Extending the HDD cage out of the chassis Depending on accessibility, it may be required to pull out the HDD cage for maintenance purposes. If it is necessary to get access to the HDD3 and HDD4, proceed the following steps: Ê...
  • Page 48 Basic hardware procedures Removing the HDD cage door Figure 6: Pulling up the lever Ê Pull up the lever of the HDD cage door (see arrow). Figure 7: Folding down the HDD cage door Ê Fold down the HDD cage door. CAUTION! The HDD cage door can only be opened after the side cover has been removed because of the anti-theft lock.
  • Page 49 Basic hardware procedures Extending the HDD cage out of the chassis Figure 8: Lifting up the lever and pulling out the HDD cage Ê Lift up the locking lever on the HDD cage (1) and pull out the HDD cage (2). The HDD cage is stopped by a screw.

  • Page 50: Removing The Front Cover

    Basic hardware procedures 4.4.3 Removing the front cover CAUTION! The side cover must be removed, before removing the front cover. Figure 9: Removing the front cover Ê Disengage the three locking tabs on the front cover by pulling it forwards (1). Ê...

  • Page 51: Reassembling

    Basic hardware procedures Reassembling CAUTION! Before attaching the covers, make sure no unnecessary parts or tools ● are left inside the server. In order to comply with applicable EMC regulations (regulations on ● electromagnetic compatibility) and satisfy cooling requirements, the server must not run while the side cover is removed.

  • Page 52: Sliding The Hdd Cage Into The Chassis

    Basic hardware procedures 4.5.2 Sliding the HDD cage into the chassis Sliding the HDD cage into the chassis Figure 11: Pushing the HDD cage in and folding down the lever Ê Push the HDD cage back into the chassis (1) and fold down the lever (2). Installing the HDD cage door Figure 12: Installing the HDD cage door Ê...
  • Page 53 Basic hardware procedures CAUTION! The HDD cage door can only be closed before the side cover has been installed because of the anti-theft lock. Figure 13: Folding down the lever Ê Fold down the lever of the HDD cage door (see arrow). Upgrade and Maintenance Manual TX1310 M3...
  • Page 54 Basic hardware procedures Installing the HDD cage cover Figure 14: Installing the HDD cage cover Ê Install the HDD cage cover. Upgrade and Maintenance Manual TX1310 M3...

  • Page 55: Installing The Side Cover

    Basic hardware procedures 4.5.3 Installing the side cover Figure 15: Installing the side cover Ê Hook the side cover in the bottom side cant of the chassis (1). Ê Push the side cover against the chassis until the locking mechanism engages (2).

  • Page 56: Connecting The Power Cord

    Basic hardware procedures Connecting the power cord CAUTION! The power supply automatically adjusts to any mains voltage in the range of 100 VAC - 240 VAC. You may only operate the server if its rated voltage range corresponds to the local mains voltage. Figure 16: Securing the power cord Ê...

  • Page 57: Switching On The Server

    Basic hardware procedures Switching on the server CAUTION! Before switching on the server, make sure the side cover is closed. In ● order to comply with applicable EMC regulations (regulations on electromagnetic compatibility) and satisfy cooling requirements, the server must not run while the side cover is removed. For further safety information, see chapter "Important information"...

  • Page 58: Handling Air Deflector

    Basic hardware procedures Handling air deflector 4.8.1 Removing the air deflector Figure 18: Removing the air deflector (A) Ê Press in the three expanding rivets on the server rear as shown (see close- up). Figure 19: Removing the air deflector (B) Ê...

  • Page 59: Installing The Air Deflector

    Basic hardware procedures 4.8.2 Installing the air deflector Figure 20: Installing the air deflector (A) Ê Fit the air deflector above the connector panel as shown. Ê Press in until the three expanding rivets on the air deflector snap into place. Figure 21: Installing the air deflector (B) Ê...
  • Page 60 Basic hardware procedures Upgrade and Maintenance Manual TX1310 M3...

  • Page 61: Basic Software Procedures

    Basic software procedures Starting the maintenance task 5.1.1 Suspending BitLocker functionality BitLocker Drive Encryption provides protection for operating system and data drives by encrypting the contents and requiring users to authenticate their credentials to access the information. In the scenario described here, BitLocker uses the compatible Trusted Platform Module (TPM) to detect if the computer's startup process has been modified from its original state.
  • Page 62 BitLocker setup wizard, it may be necessary to modify the BitLocker Group Policy settings. For more information on how to suspend BitLocker drive encryption, see the Microsoft TechNet library at http://technet.microsoft.com/library/cc731549.aspx. For more information, see the Fujitsu web pages. Upgrade and Maintenance Manual TX1310 M3...

  • Page 63: Removing Backup And Optical Disk Media

    For Japan: Please contact Fujitsu support, if "forcible" tape ejection is necessary. Fujitsu does not assume responsibility for any damage to the tape drive, the data cartridge/tape or for the loss of any data resulting from manual tape extraction procedures.

  • Page 64: Completing The Maintenance Task

    Updating or recovering the system board BIOS After replacing the system board or a CPU, it is essential to upgrade the BIOS to the latest version. The latest BIOS version is available from the Fujitsu support internet pages at: http://ts.fujitsu.com/support/ For Japan: http://www.fujitsu.com/jp/products/computing/servers/primergy/downloads/...

  • Page 65: Enabling Option Rom Scan

    Basic software procedures 5.2.2 Enabling Option ROM scan In order to configure an expansion card that has been installed or replaced, the Option ROM of the card has to be enabled in the BIOS. The firmware of the card is called by the BIOS upon reboot and can be entered and configured. Option ROM can be enabled permanently (e.g.

  • Page 66: Reconfiguring The Backup Software Solution

    More information on suitable backup software solutions and related documentation is available from the Fujitsu web pages. Re-enabling backup drives If a backup drive has been disabled or deleted from the backup software drive list as described in section "Verifying and configuring the backup software...

  • Page 67: Verifying The System Time Settings

    Basic software procedures Ê Reset replaced components to Enable. Ê Save your changes and exit the BIOS. For more information on how to access the BIOS and modify settings, see the corresponding BIOS Setup Utility reference manual. 5.2.5 Verifying the system time settings This task only applies to Linux and VMware environments.

  • Page 68: Viewing The System Event Log (Sel)

    Basic software procedures 5.2.6 Viewing the System Event Log (SEL) 5.2.6.1 Viewing the SEL You can view the System Event Log (SEL) using the ServerView Operations Manager: Viewing the SEL in ServerView Operations Manager Ê In ServerView Operations Manager Single System View select Maintenance from the Information / Operation menu.

  • Page 69: Updating The Nic Configuration File In A Linux And Vmware Environment

    Basic software procedures 5.2.7 Updating the NIC configuration file in a Linux and VMware environment In order to prevent errors caused by changing network device names (eth<x>), it is recommended to store the MAC address (hardware address) of a network interface card in the related NIC configuration file of the Linux/VMware OS.

  • Page 70: Resuming Bitlocker Functionality

    Basic software procedures Ê For the changes to take effect, you need to reboot the network by entering the following command: # service network restart If the system board or network controller offers multiple LAN ports, it is necessary to update the remaining ifcfg-eth<x> definition files accordingly.

  • Page 71: Performing A Raid Array Rebuild

    For more information on how to resume BitLocker drive encryption, see the Microsoft TechNet library at http://technet.microsoft.com/library/cc731549.aspx. For more information, see the Fujitsu web pages. 5.2.9 Performing a RAID array rebuild After replacing an HDD that has been combined into a RAID array, RAID rebuild will be performed completely unattended as a background process.

  • Page 72: Looking Up Changed Mac / Wwn Addresses

    After replacing the Chassis ID EPROM, system information has to be entered using the Chassis ID Prom tool. The tool and further instructions are available to maintenance personnel from the Fujitsu web pages: https://partners.ts.fujitsu.com/com/service/ps/Servers/PRIMERGY/ Ê Select your PRIMERGY system from the main area of the page.

  • Page 73: Configuring Lan Teaming

    Basic software procedures Ê In the Tools area click Tools: Chassis-IDProm Tool to download the file (tool-chassis-Idprom-Tool.zip). For Japan: Follow the instructions provided separately. 5.2.12 Configuring LAN teaming Use ServerView Operations Manager to obtain more information on existing LAN teams: Ê...
  • Page 74 Basic software procedures Ê If LAN teaming has been active, you will need to restore the configuration using the LAN driver utility or OS teaming software. For more information, see the relevant LAN driver manual. Upgrade and Maintenance Manual TX1310 M3...

  • Page 75: Power Supply Unit (Psu)

    Power supply unit (PSU) Safety notes CAUTION! Do not disassemble the PSU. Doing so may cause electric shock. ● Areas around the PSU may remain extremely hot after shutdown. ● After shutting down the server, wait for hot components to cool down before removing the PSU.

  • Page 76: Replacing The Psu

    Power supply unit (PSU) Replacing the PSU Field Replaceable Unit Hardware: 10 minutes (FRU) Tools: Phillips PH2 / (+) No. 2 screw driver 6.2.1 Preliminary steps "Shutting down the server" on page 44 Ê "Disconnecting the power cord" on page 45 Ê...
  • Page 77 Power supply unit (PSU) Figure 24: Removing screws Ê Remove four screws from the PSU and three screws from the chassis (see circles). Figure 25: Pulling out the system board tray Ê Pull the system board tray out of the chassis by 4-5 cm. Upgrade and Maintenance Manual TX1310 M3...
  • Page 78 Power supply unit (PSU) Figure 26: Removing the PSU Ê Slide the PSU to the right about 2 cm to disengage the locking mechanism (1). Ê Lift the PSU about 4 cm (2) and remove it out of the chassis in a slight angle (3).

  • Page 79: Installing The Psu

    Power supply unit (PSU) 6.2.3 Installing the PSU Figure 27: Inserting the PSU Ê Insert the PSU into the chassis in a slight angle (1) and position it in place (2). Ê Slide the PSU towards the rear of the chassis as far as it will go (3). Upgrade and Maintenance Manual TX1310 M3...
  • Page 80 Power supply unit (PSU) Figure 28: Sliding the system board tray into the chassis Ê Slide the system board tray back into the chassis. Upgrade and Maintenance Manual TX1310 M3...
  • Page 81 Power supply unit (PSU) Figure 29: Fastening the screws Ê Fasten the PSU with four screws and the chassis with three screws (see circles). Figure 30: Connecting power cable Ê Connect the power cable to the system board connector "PWR12V". Ê...

  • Page 82: Concluding Steps

    Power supply unit (PSU) 6.2.4 Concluding steps "Sliding the HDD cage into the chassis" on page 52 Ê "Reassembling" on page 51 Ê "Connecting the power cord" on page 56 Ê "Switching on the server" on page 57 Ê Upgrade and Maintenance Manual TX1310 M3...

  • Page 83: Hard Disk Drives (Hdds)

    Hard disk drives (HDDs) Safety notes CAUTION! Before removing several HDD/SSD modules, make sure that all ● HDD/SSD modules can be reinstalled into their original bay. Otherwise, data may be lost. Do not touch the circuitry on boards or soldered parts. Hold circuit ●...

  • Page 84: Basic Information

    Hard disk drives (HDDs) Basic information 7.1.1 General equipping rules – HDDs with different capacities are installed from highest to lowest capacity. – HDDs with different rotation speeds are installed from highest to lowest speed. – Maximum configuration: 4x 3.5-inch HDDs 7.1.2 Mounting order Figure 31: 3.5-inch HDD mounting order...

  • Page 85: Installing 3.5-Inch Hdds

    Hard disk drives (HDDs) Installing 3.5-inch HDDs Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 7.2.1 Preliminary steps "Shutting down the server" on page 44 Ê "Disconnecting the power cord" on page 45 Ê "Getting access to the component" on page 46 Ê...

  • Page 86: Installing A 3.5-Inch Hdd

    Hard disk drives (HDDs) 7.2.3 Installing a 3.5-inch HDD Figure 34: Aligning the Easyrails Ê Align the two pins on the Easyrails with the screw holes on the HDD. Figure 35: Attaching the Easyrails Ê Attach an Easyrail each side of the HDD. Upgrade and Maintenance Manual TX1310 M3...

  • Page 87: Concluding Steps

    Hard disk drives (HDDs) Figure 36: Inserting the 3.5-inch HDD Ê Insert the HDD into its drive bay. Ê Slide the HDD into its drive bay until the Easyrails click in place. Ê When using a RAID array, add the additional HDD/SSD to the RAID array. Configuring the RAID array, refer to the documentation of the RAID controller, used in your configuration, see section "Documents you...

  • Page 88: Removing 3.5-Inch Hdds

    Hard disk drives (HDDs) Removing 3.5-inch HDDs Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 7.3.1 Preliminary steps Ê If the HDD module to be removed is combined into a RAID array, please proceed as follows: RAID level Procedure Only remove an HDD module combined in a RAID 0 array if defective.
  • Page 89 Hard disk drives (HDDs) CAUTION! All data on all HDDs in the array will be lost when deleting the RAID array! Be sure to back up your data before deleting a RAID array. For further information, see the "ServerView Suite RAID Management" user guide.

  • Page 90: Removing A 3.5-Inch Hdd

    Hard disk drives (HDDs) 7.3.2 Removing a 3.5-inch HDD Figure 37: Removing a 3.5-inch HDD Ê Press in on the green handles on the Easyrails (1) to disengage the locking mechanism. Ê Pull the HDD completely out of its drive bay (2). Figure 38: Detaching the Easyrails Ê...

  • Page 91: Inserting Easyrails In The Upper Hdd Bay

    Hard disk drives (HDDs) 7.3.3 Inserting Easyrails in the upper HDD bay Store unused Easyrails inside their drive bays to have them at hand if needed. Figure 39: Inserting the Easyrails into their HDD bay Ê Push the Easyrails completely into the bay (1). Ê...

  • Page 92: Replacing A 3.5-Inch Hdd

    Hard disk drives (HDDs) Replacing a 3.5-inch HDD Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less CAUTION! All HDDs must be uniquely identified so that they can be reinstalled in their original mounting locations later. If this is not done, existing data can be lost.

  • Page 93: Concluding Steps

    Hard disk drives (HDDs) 7.4.4 Concluding steps "Reassembling" on page 51 Ê "Connecting the power cord" on page 56 Ê "Switching on the server" on page 57 Ê "Performing a RAID array rebuild" on page 71 Ê Upgrade and Maintenance Manual TX1310 M3...
  • Page 94 Hard disk drives (HDDs) Upgrade and Maintenance Manual TX1310 M3...

  • Page 95: System Fans

    System fans Safety notes CAUTION! Do not damage or modify internal cables or devices. Doing so may ● cause a device failure, fire, or electric shock. Devices and components inside the server remain hot after ● shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options.

  • Page 96: Basic Information

    System fans Basic information CAUTION! Since the system fans are not redundant they have to be replaced immediately in case of defects or pre-failure events. Figure 40: Positions of the system fans Rear fan (Fan OEM) CPU fan (implemented in the heat sink) Front fan (Fan SYS) The CPU fan is implemented in the heat sink.

  • Page 97: Replacing The Rear Fan

    System fans Replacing the rear fan Upgrade and Repair Unit Hardware: 15 minutes (URU) Tools: diagonal pliers 8.2.1 Preliminary steps "Shutting down the server" on page 44 Ê "Disconnecting the power cord" on page 45 Ê "Getting access to the component" on page 46 Ê...
  • Page 98 System fans Figure 42: Removing the defective rear fan Ê Extend the defective rear fan somewhat (see arrow). Ê Cut through the four rubber rivets between the rear fan and the chassis using a diagonal pliers in sequence 1-4. Upgrade and Maintenance Manual TX1310 M3...

  • Page 99: Installing The New Rear Fan

    System fans 8.2.3 Installing the new rear fan Figure 43: Inserting new rubber rivets Ê Lead the four rubber rivets through the screw holes on the rear chassis wall. Ê Pull tight until the sockets on the rubber rivets properly engage with the rear chassis wall.
  • Page 100 System fans Figure 44: Installing the rear fan Ê Lead the loose ends of the rubber rivets through the four screw holes on the new rear fan. Ê Pull tight until the expanding plug on the rubber rivet engages with the fan (see close-up).
  • Page 101 System fans Figure 45: Cutting off the rubber rivets Ê Cut off the loose ends of the four rubber rivets as shown. Figure 46: Connecting the rear fan cable Ê Connect the rear fan cable to system board connector "Fan (OEM)". Ê...

  • Page 102: Concluding Steps

    System fans 8.2.4 Concluding steps "Installing the air deflector" on page 59 Ê "Sliding the HDD cage into the chassis" on page 52 Ê "Reassembling" on page 51 Ê "Connecting the power cord" on page 56 Ê "Switching on the server" on page 57 Ê...

  • Page 103: Replacing The Front Fan

    System fans Replacing the front fan Upgrade and Repair Unit Hardware: 15 minutes (URU) Tools: tool-less 8.3.1 Preliminary steps "Shutting down the server" on page 44 Ê "Disconnecting the power cord" on page 45 Ê "Getting access to the component" on page 46 Ê...
  • Page 104 System fans Figure 48: Removing the rear fan cage (1) Ê Disengage the front fan cage: Pull out on the locking latch (1) while pushing the fan cage to the left (2). Ê Remove the fan cage (3). Upgrade and Maintenance Manual TX1310 M3...

  • Page 105: Installing The New Front Fan

    System fans 8.3.3 Installing the new front fan Figure 49: Installing the front fan cage Ê Slightly offset to the left, fit the front fan cage on the server front (1). Ê Push the fan cage to the right (2) until the locking latch (3) engages. Figure 50: Connecting the rear fan cable Ê...

  • Page 106: Concluding Steps

    System fans 8.3.4 Concluding steps "Reassembling" on page 51 Ê "Connecting the power cord" on page 56 Ê "Switching on the server" on page 57 Ê Upgrade and Maintenance Manual TX1310 M3...

  • Page 107: Expansion Cards And Backup Units

    Expansion cards and backup units Safety notes CAUTION! Do not damage or modify internal cables or devices. Doing so may ● cause a device failure, fire, or electric shock. Devices and components inside the server remain hot after ● shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options.

  • Page 108: Basic Information

    Expansion cards and backup units Basic information Figure 51: PCI slot overview PCI slot Type Function PCIe x1 PCIe x1 slot Gen 3 (notched, but if TPM is mounted, restricted to x4 PCIe Cards) PCIe x1 PCIe x1 slot Gen 3 (notched) PCIe x16 PCIe x4 slot Gen 3 (mechanically x16, support for VGA Adapter D3453)
  • Page 109 Adapter Product Name Adapter Controller Card – Graphic NVIDIA NVIDIA NVS 315 PCI-E x16, 1GB, Dual-DVI-I or Dual VGA Fujitsu VGA extension card Controller Card - Intel PLAN AP 1x1Gbit Cu Intel I210-T1 (Beaver Lake) Intel PLAN CP 2x1Gbit Cu Intel I350-T2...

  • Page 110: Handling Slot Brackets

    Expansion cards and backup units Handling slot brackets 9.2.1 Installing a slot bracket Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver / hexagon screw driver 5 mm Use the low profile bracket perforated for relevant controllers. No bracket needed for installing the HDD controller in slot 1 of riser module 1.
  • Page 111 Expansion cards and backup units Example network adapter Figure 54: Placing the slot bracket Ê Place the controller on the slot bracket (1). Ê Carefully shift the slot bracket towards the controller (2). Ê Ensure that the ESD springs properly engage with the slot bracket as shown (see circles).

  • Page 112: Removing A Slot Bracket

    Expansion cards and backup units 9.2.2 Removing a slot bracket Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: – Phillips PH2 / (+) No. 2 screw driver – Hexagon nut 5 mm (for hexagon bolt) Removing the slot bracket Ê...

  • Page 113: Expansion Cards

    Expansion cards and backup units Expansion cards 9.3.1 Installing expansion cards Upgrade and Repair Unit Hardware: 5 minutes (URU) Software: 5 minutes Tools: Only for installing slot brackets: – Phillips PH2 / (+) No. 2 screw driver – Hexagon nut 5 mm (for hexagon bolt) 9.3.1.1 Preliminary steps "Suspending BitLocker functionality"...

  • Page 114: Removing The Pci Slot Bracket

    Expansion cards and backup units 9.3.1.2 Removing the PCI slot bracket Figure 56: Removing the PCI slot bracket Ê Open the slot bracket clamp (1). Ê Remove the desired slot bracket (2). CAUTION! Keep the slot bracket for future use. Always replace slot brackets into unused PCI slot openings to comply with applicable EMC regulations and satisfy cooling requirements.

  • Page 115: Installing An Expansion Card

    Expansion cards and backup units 9.3.1.3 Installing an expansion card Ê Remove the expansion card from its protective packaging. For further instructions regarding controller settings, please refer to the accompanying documentation. Ê If applicable, attach the required slot bracket to the expansion card, see section "Installing a slot bracket"...

  • Page 116: Concluding Steps

    Expansion cards and backup units 9.3.1.4 Concluding steps "Reassembling" on page 51 Ê Ê If applicable, connect external cables to the expansion card. "Connecting the power cord" on page 56 Ê "Switching on the server" on page 57 Ê Ê If applicable, "Enabling Option ROM scan"...

  • Page 117: Removing An Expansion Card

    Expansion cards and backup units 9.3.2.2 Removing an expansion card Ê If applicable, disconnect internal cables from the expansion card. Figure 58: Removing an expansion card Ê Open the slot bracket clamp (1). Ê Carefully remove the expansion card from its slot (2). Upgrade and Maintenance Manual TX1310 M3...

  • Page 118: Installing A Pci Slot Bracket

    Expansion cards and backup units 9.3.2.3 Installing a PCI slot bracket CAUTION! Always replace slot brackets into unused PCI slot openings to comply with applicable EMC regulations and satisfy cooling requirements. Figure 59: Installing a PCI slot bracket Ê Insert a PCI slot bracket into the unused PCI slot opening (1). Ê...

  • Page 119: Replacing Expansion Cards

    Expansion cards and backup units 9.3.3 Replacing expansion cards Upgrade and Repair Unit Hardware: 5 minutes (URU) Software: 5 minutes Tools: Only for installing or removing slot brackets: – Phillips PH2 / (+) No. 2 screw driver – Hexagon nut 5 mm (for hexagon bolt) Note on network settings recovery When replacing network controllers or the system board, network configuration settings in the operating system will be lost and replaced...

  • Page 120: Installing An Expansion Card

    Expansion cards and backup units 9.3.3.3 Installing an expansion card Ê If applicable, install a slot bracket on the new expansion card, see section "Installing a slot bracket" on page 110. Ê Install the new expansion card, see section "Installing an expansion card" on page 115.

  • Page 121: Main Memory

    Main memory Safety notes CAUTION! Do not install unsupported third party memory modules. For further ● information on supported memory modules, refer to section "Basic information" on page 122. Doing so may cause electric shock, a fire, or failures. Memory modules remain hot after shutdown. Wait for components to ●...

  • Page 122: Basic Information

    Main memory 10.1 Basic information Figure 60: Slots of the main memory – The system board is equipped with four memory slots. – The system has to be equipped with at least one memory module. Populate memory slot 1 / channel A (CHA1) first. Upgrade and Maintenance Manual TX1310 M3...

  • Page 123: Memory Sequence

    Main memory 10.1.1 Memory sequence – Populate memory slot 1 / channel A (CHA1) first. – Within both channels, memory slot 1 must be populated prior to slot 2. – If memory modules with different capacities are used: – Install modules with higher capacities first. –...

  • Page 124: Installing Memory Modules

    Main memory 10.2 Installing memory modules Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 10.2.1 Preliminary steps "Suspending BitLocker functionality" on page 61 Ê "Shutting down the server" on page 44 Ê "Disconnecting the power cord" on page 45 Ê...

  • Page 125: Concluding Steps

    Main memory Figure 62: Installing a memory module Ê Align the notch on the bottom of the module with the crossbar in the slot. Ê Press down on the memory module until the securing clips snap into the cutouts at each end of the module. 10.2.3 Concluding steps "Reassembling"...

  • Page 126: Removing Memory Modules

    Main memory 10.3 Removing memory modules Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 10.3.1 Preliminary steps "Suspending BitLocker functionality" on page 61 Ê "Shutting down the server" on page 44 Ê "Disconnecting the power cord" on page 45 Ê...

  • Page 127: Concluding Steps

    Main memory Figure 64: Installing a memory module Ê Remove the ejected memory module. Ê Close the securing clips. CAUTION! If the clips are open, they can collide with a cable clamp. 10.3.3 Concluding steps "Reassembling" on page 51 Ê "Connecting the power cord"...

  • Page 128: Replacing Memory Modules

    Main memory 10.4 Replacing memory modules Upgrade and Repair Unit Hardware: 5 minutes (URU) Software: 5 minutes Tools: tool-less 10.4.1 Preliminary steps "Suspending BitLocker functionality" on page 61 Ê "Shutting down the server" on page 44 Ê "Disconnecting the power cord" on page 45 Ê...

  • Page 129: Processor (Cpu)

    Processor (CPU) Safety notes CAUTION! Do not install unsupported CPUs. For further information on ● supported CPUs, see section "Basic information" on page 130. Circuit boards and soldered parts of internal options are exposed and ● can be damaged by static electricity. Always discharge static build-up (e.g.

  • Page 130: Basic Information

    Basic information Figure 65: Position CPU socket The system board supports one CPU socket. For system relevant information, refer to your server’s hardware configurator available online at the following address: http://ts.fujitsu.com/products/standard_servers/index.htm For Japan: http://jp.fujitsu.com/platform/server/primergy/system/ Upgrade and Maintenance Manual TX1310 M3...

  • Page 131: Upgrading Or Replacing The Cpu

    Processor (CPU) 11.2 Upgrading or replacing the CPU Field Replaceable Unit Hardware: 15 minutes (FRU) Software: 5 minutes Tools: Phillips PH2 / (+) No. 2 screw driver CAUTION! CPUs are modules which are extremely sensitive to electro-static discharges and therefore must always be handled with care. After a CPU has been removed from its protective sleeve or from its socket, place it top down on a non-conducting, antistatic surface.

  • Page 132: Removing The Heat Sink

    Processor (CPU) 11.2.2 Removing the heat sink Figure 66: Removing the heat sink (A) Ê Disconnect the CPU fan cable from system board connector "Fan (CPU)". Upgrade and Maintenance Manual TX1310 M3...
  • Page 133 Processor (CPU) Figure 67: Removing the heat sink (B) Ê Loosen the four captive screws on the heat sink in a crossover pattern (1-4). Upgrade and Maintenance Manual TX1310 M3...
  • Page 134 Processor (CPU) Figure 68: Removing the heat sink (C) Ê Carefully turn the heat sink back and forth to detach it from the CPU (1). This may be necessary due to the adhesive quality of the thermal paste located between the heat sink and CPU. CAUTION! Pay special attention not to damage any system board components surrounding the CPU socket.

  • Page 135: Removing The Cpu

    Processor (CPU) 11.2.3 Removing the CPU Figure 69: Opening socket release lever Ê Unlatch the socket release lever by pushing it down and away from the socket (1). Ê Fold back the socket release lever (2). Upgrade and Maintenance Manual TX1310 M3...
  • Page 136 Processor (CPU) Figure 70: Opening the load plate Ê Rotate the socket lever to lift the load plate away from the socket. Ê Make sure that the load plate is in the fully open position. Upgrade and Maintenance Manual TX1310 M3...
  • Page 137 Processor (CPU) Figure 71: Removing the CPU Ê Carefully remove the CPU from its socket in a vertical motion. CAUTION! Be careful not to touch or bend the spring contacts on the CPU socket. Upgrade and Maintenance Manual TX1310 M3...

  • Page 138: Installing The Cpu

    Processor (CPU) 11.2.4 Installing the CPU Ê Confirm that the CPU model number printed on the top of the CPU fits with the requirements. Ê If applicable, remove the protective cap from the bottom side of the CPU. Figure 72: Installing the CPU Ê...
  • Page 139 Processor (CPU) Figure 73: Closing the load plate (A) Ê Lower the load plate over the CPU while leaving the socket lever in its open position. Upgrade and Maintenance Manual TX1310 M3...
  • Page 140 Processor (CPU) Figure 74: Closing the load plate (B) Ê Lower the socket lever while making sure that the front edge of the load plate slides under the shoulder screw cap (see close-up) as the lever is lowered. Figure 75: Closing the socket release lever Ê...

  • Page 141: Applying Thermal Paste

    Processor (CPU) 11.2.5 Applying thermal paste For Japan, the service engineer must follow the instruction provided separately. If the CPU upgrade or replacement kit contains a new CPU heat sink, a thin layer of thermal compound has already been pre-applied to its lower surface.
  • Page 142 Processor (CPU) Figure 77: Applying thermal paste Ê Apply a small point-shaped amount of thermal paste (1.0 gram, see description above) to the center of the CPU surface as shown. CAUTION! Do not mix different types of thermal paste. Upgrade and Maintenance Manual TX1310 M3...

  • Page 143: Installing The Heat Sink

    Processor (CPU) 11.2.6 Installing the heat sink Figure 78: Installing the heat sink (A) Ê Carefully seat the heat sink on the four threaded holes as shown (1). CAUTION! – Ensure that the screws on the heat sink are properly seated on the threaded holes (see circles).
  • Page 144 Processor (CPU) Figure 79: Installing the heat sink (B) Ê Fasten the four captive screws on the heat sink in a crossover pattern (screw torque: 0.6 Nm, not applicable for Japan) (1-4). Upgrade and Maintenance Manual TX1310 M3...

  • Page 145: Concluding Steps

    Processor (CPU) Figure 80: Connecting the CPU fan cable Ê Connect the CPU fan cable to system board connector "Fan (CPU)". 11.2.7 Concluding steps "Sliding the HDD cage into the chassis" on page 52 Ê "Reassembling" on page 51 Ê "Connecting the power cord"...
  • Page 146 Processor (CPU) Ê In the Save & Exit menu, select Save Changes and Exit or Save Changes and Reset. Ê If applicable, "Updating or recovering the system board BIOS" on page 64 "Resuming BitLocker functionality" on page 70 Ê Upgrade and Maintenance Manual TX1310 M3...

  • Page 147: Replacing The Heat Sink

    Processor (CPU) 11.3 Replacing the heat sink Field Replaceable Unit Hardware: 15 minutes (FRU) Tools: Phillips PH2 / (+) No. 2 screw driver The CPU fan is implemented in the heat sink. When the CPU fan is defective, the heat sink must be replaced. 11.3.1 Preliminary steps "Shutting down the server"...

  • Page 148: Handling The Protective Cover

    Processor (CPU) "Connecting the power cord" on page 56 Ê "Switching on the server" on page 57 Ê 11.4 Handling the protective cover 11.4.1 Installing the protective cover Figure 81: Attaching the protective socket cover Ê Carefully lower the protective socket cover onto the CPU socket in a vertical motion until it snaps in place.
  • Page 149 Processor (CPU) Figure 82: Closing the load plate (A) Ê Lower the load plate over the CPU cover while leaving the socket lever in its open position. Upgrade and Maintenance Manual TX1310 M3...
  • Page 150 Processor (CPU) Figure 83: Closing the load plate (B) Ê Lower the socket lever while making sure that the front edge of the load plate slides under the shoulder screw cap (see close-up) as the lever is lowered. Figure 84: Latching the socket lever Ê...

  • Page 151: Removing The Protective Cover

    Processor (CPU) 11.4.2 Removing the protective cover Figure 85: Opening socket release lever Ê Unlatch the socket release lever by pushing it down and away from the socket (1). Ê Fold back the socket release lever (2). Upgrade and Maintenance Manual TX1310 M3...
  • Page 152 Processor (CPU) Figure 86: Opening the load plate Ê Press down on the socket lever to lift the load plate away from the socket. Ê Fully open the load plate. Upgrade and Maintenance Manual TX1310 M3...
  • Page 153 Processor (CPU) Figure 87: Removing the protective cover Ê Remove the protective cover from the CPU socket. Proceed as follows: Ê Place your thumb against the front edge of the protective socket cover and rest your index finger on the rear grip. Ê...
  • Page 154 Processor (CPU) Upgrade and Maintenance Manual TX1310 M3...

  • Page 155: Accessible Drives

    Accessible drives Safety notes CAUTION! Before installing an accessible drive, acquaint yourself with the ● drive's user documentation. When inserting an accessible drive into the server, ensure not to ● pinch or strain any connected cables. When installing an accessible drive, hold it by its sides. Applying force ●...

  • Page 156: Basic Information

    Accessible drives 12.1 Basic information Mounting order for accessible drives The server offers one ultra slimline ODD bay and one 5.25-inch bay for backup drives. Figure 88: Accessible drive bays Sequence Accessible drive Max. # Slimline ODD Bay 1 RDX backup drive Bay 2 Table 6: Accessible drive mounting sequence Upgrade and Maintenance Manual...

  • Page 157: Optical Disk Drive (Odd)

    Accessible drives 12.2 Optical disk drive (ODD) 12.2.1 Installing an ODD Upgrade and Repair Unit Hardware: 10 minutes (URU) Tools: tool-less 12.2.1.1 Preliminary steps "Suspending BitLocker functionality" on page 61 Ê "Shutting down the server" on page 44 Ê "Disconnecting the power cord" on page 45 Ê...

  • Page 158: Preparing The Odd

    Accessible drives 12.2.1.3 Preparing the ODD There are two fixation plates for accessible drives. You need one fixation plate for every accessible drive to be installed. Figure 90: Removing the fixation plate from the chassis Ê Unclip the fixation plate (see arrow). Figure 91: Attaching the fixation plate to the ODD Ê...

  • Page 159: Installing The Odd

    Accessible drives 12.2.1.4 Installing the ODD Figure 92: Installing the ODD Ê While pressing the fixation plate against the ODD, insert the ODD into accessible drive bay 1 and push until it is firmly seated in its connector on the ODD back plate. Since the ODD is connected to the ODD back plate, no further cable connection is necessary.

  • Page 160: Removing An Odd

    Accessible drives 12.2.2 Removing an ODD Upgrade and Repair Unit Hardware: 10 minutes (URU) Tools: tool-less 12.2.2.1 Preliminary steps "Suspending BitLocker functionality" on page 61 Ê "Removing backup and optical disk media" on page 63 Ê "Verifying and configuring the backup software solution" on page 63 Ê...

  • Page 161: Concluding Steps

    Accessible drives 12.2.2.3 Concluding steps Ê Remove the fixation plates from the removed accessible drives. Ê Secure the fixation plates in the chassis. "Reassembling" on page 51 Ê "Connecting the power cord" on page 56 Ê "Switching on the server" on page 57 Ê...

  • Page 162: Concluding Steps

    Accessible drives Figure 94: Attaching the fixation plate to the ODD Ê Align the two pins on the fixation plate with the screw holes on the new ODD. Ê Attach the fixation plate to the left side of the new ODD. Ê...

  • Page 163: Backup Drive (Rdx)

    Accessible drives 12.3 Backup drive (RDX) 12.3.1 Installing a backup drive Upgrade and Repair Unit Hardware: 10 minutes (URU) Tools: – diagonal pliers (for removing the metal bay cover) – Phillips PH2 / (+) No. 2 screw driver (for removing the PSU) 12.3.1.1 Preliminary steps "Suspending BitLocker functionality"...

  • Page 164: Removing The Dummy Cover Bay 2

    Accessible drives 12.3.1.2 Removing the dummy cover bay 2 If bay 2 is to be equipped, it is necessary to remove its dummy cover and metal bay cover. CAUTION! You cannot install the metal bay cover again. Only remove metal bay cover before installing RDX drive to comply with applicable EMC regulations and satisfy cooling requirements.
  • Page 165 Accessible drives Add gaskets to the following three positions to comply with current EMC regulations. Gaskets are included in the RDX option kit. Ê Clean the metal surface before sticking the gaskets. Ê Remove the protection film from the adhesive tape shortly before sticking it to the desired location.

  • Page 166: Ê Install The Front Cover, See Section "Installing The Front Cover" On Page

    Accessible drives Figure 99: Top side at the front Ê Add the gasket (70 mm) on the top side at the front of bay 2. Ê Install the front cover, see section "Installing the front cover" on page Upgrade and Maintenance Manual TX1310 M3...

  • Page 167: Preparing The Backup Drive

    Accessible drives 12.3.1.3 Preparing the backup drive There are two fixation plates for accessible backup drives. You need one fixation plate for every accessible backup drive to be installed. Figure 100: Removing the fixation plate from the chassis Ê Unclip the fixation plate (see arrow). Figure 101: Attaching the fixation plate to the backup drive Ê...

  • Page 168: Installing The Backup Drive

    Accessible drives 12.3.1.4 Installing the backup drive For easier access to the backup drive connectors, it is recommended to remove the PSU before installing the backup drive. Figure 102: Installing backup drive Ê While pressing the fixation plate against the backup drive, insert the backup drive into accessible drive bay 2.

  • Page 169: Concluding Steps

    Accessible drives 12.3.1.5 Concluding steps "Sliding the HDD cage into the chassis" on page 52 Ê "Reassembling" on page 51 Ê "Connecting the power cord" on page 56 Ê "Switching on the server" on page 57 Ê "Reconfiguring the backup software solution" on page 66 Ê...

  • Page 170: Removing A Backup Drive

    Accessible drives 12.3.2.2 Removing a backup drive For easier access to the backup drive connectors, it is recommended to remove the PSU before removing the backup drive. Figure 104: Removing backup drive Ê Slide the locking latch in the direction of the arrow (1) and press somewhat out the backup drive from behind (2).

  • Page 171: Replacing A Backup Drive

    Accessible drives 12.3.3 Replacing a backup drive Upgrade and Repair Unit Hardware: 15 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver (for removing the PSU) 12.3.3.1 Preliminary steps "Suspending BitLocker functionality" on page 61 Ê "Removing backup and optical disk media" on page 63 Ê...

  • Page 172: Concluding Steps

    Accessible drives Ê Attach the fixation plate on the left side of the new backup drive. Ê Install the new backup drive, see section "Installing the backup drive" on page 168. 12.3.3.3 Concluding steps "Sliding the HDD cage into the chassis" on page 52 Ê...

  • Page 173: Front Panel And Front Usb

    Front panel and front USB Front connectors and indicators are integral parts of the system board. There is no individual front panel module. In case of defective front connectors or indicators, the system board needs to be replaced. Proceed as described in section "Replacing the system board"...
  • Page 174 Front panel and front USB Upgrade and Maintenance Manual TX1310 M3...

  • Page 175: Serial Connector

    Serial connector Safety notes CAUTION! For further safety information, please refer to chapter "Important information" on page 14.1 Installing the serial connector Upgrade and Repair Unit Hardware: 5 minutes (URU) Tool: – flat screw driver – Hexagon screw driver 5 mm 14.1.1 Preliminary steps "Shutting down the server"...

  • Page 176: Breaking Off The Metal Cover

    Serial connector 14.1.2 Breaking off the metal cover Figure 106: Removing the serial connector metal cover Ê Twist and break off the metal cover. Use a flat screw driver to break off the metal cover. 14.1.3 Installing the serial connector Ê...

  • Page 177: Concluding Steps

    Serial connector Figure 108: Installing the serial connector (B) Ê Fasten the serial connector with two hexagon bolts. 14.1.4 Concluding steps "Installing the air deflector" on page 59 Ê "Reassembling" on page 51 Ê "Connecting the power cord" on page 56 Ê...

  • Page 178: Removing The Serial Connector

    Serial connector 14.2 Removing the serial connector Upgrade and Repair Unit Hardware: 5 minutes (URU) Tool: Hexagon screw driver 5 mm 14.2.1 Preliminary steps "Shutting down the server" on page 44 Ê "Disconnecting the power cord" on page 45 Ê "Getting access to the component"...

  • Page 179: Concluding Steps

    Serial connector Figure 110: Removing the serial connector (B) Ê Remove the serial connector (1). Ê Remove the cable from the system board (2). 14.2.3 Concluding steps "Installing the air deflector" on page 59 Ê "Reassembling" on page 51 Ê "Connecting the power cord"...

  • Page 180: Replacing The Serial Connector

    Serial connector 14.3 Replacing the serial connector Upgrade and Repair Unit Hardware: 5 minutes (URU) Tool: Hexagon screw driver 5 mm 14.3.1 Preliminary steps "Shutting down the server" on page 44 Ê "Disconnecting the power cord" on page 45 Ê "Getting access to the component"...

  • Page 181: System Board And Components

    System board and components Safety notes CAUTION! Devices and components inside the server remain hot after ● shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options. Circuit boards and soldered parts of internal options are exposed and ●...

  • Page 182: Replacing The Cmos Battery

    System board and components 15.2 Replacing the CMOS battery Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less; recommended: tooth pick Safety notes CAUTION! The CMOS battery must be replaced with an identical battery or with ● a battery type recommended by the manufacturer. Keep lithium batteries away from children.

  • Page 183: Replacing The Defective Cmos Battery

    System board and components 15.2.2 Replacing the defective CMOS battery Figure 111: Replacing the CMOS battery Ê Press the locking spring into direction of the arrow (1), so that the CMOS battery jumps out of its socket. Ê Remove the CMOS battery (2). CAUTION! Sharp tools such as screw drivers might damage system board components in case of slipping.

  • Page 184: Concluding Steps

    System board and components 15.2.3 Concluding steps Ê Dispose of the CMOS battery in accordance with local regulations concerning special waste. "Reassembling" on page 51 Ê "Connecting the power cord" on page 56 Ê "Switching on the server" on page 57 Ê...

  • Page 185: Trusted Platform Module (Tpm)

    System board and components 15.3 Trusted Platform Module (TPM) There are different TPM kits available. The procedures of installing, removing and replacing are identic. Figure 112: TPM installation kit - example 1 Figure 113: TPM installation kit - example 2 TPM (Trusted Platform Module) Special screw for TPM TPM spacer...

  • Page 186: Installing The Tpm

    System board and components 15.3.1 Installing the TPM Field Replaceable Unit Hardware: 5 minutes (FRU) Software: 5 minutes Tools: – Bit screw driver – TPM bit insert For Japan – TPM module fixing tool (S26361-F3552-L909) 15.3.1.1 Preliminary steps "Shutting down the server" on page 44 Ê...
  • Page 187 System board and components Figure 115: TPM bit insert Ê Attach the TPM bit insert or TPM module fixing tool (Japan) to a bit screw driver. Figure 116: Installing the TPM Ê Connect the TPM to the system board (1). Ê...

  • Page 188: Concluding Steps

    System board and components 15.3.1.3 Concluding steps Ê Install all expansion cards, see section "Expansion cards" on page 113. Make sure that you reinstall each card in the slot it was located before the replacement. "Reassembling" on page 51 Ê "Connecting the power cord"...

  • Page 189: Removing The Tpm

    System board and components 15.3.2 Removing the TPM Field Replaceable Unit Hardware: 30 minutes (FRU) Tools: Removing the system board: – Phillips PH2 / (+) No. 2 screw driver Removing the TPM: – Bit screw driver – Flat nose pliers –...
  • Page 190 For further information on how to disable BitLocker drive encryption, please refer to the Microsoft Knowledge Base. Please refer to the Fujitsu web pages for more details. Ê Disable TPM in the system board BIOS. Proceed as follows: Ê Switch on or restart your server.

  • Page 191: Removing The Tpm

    System board and components 15.3.2.2 Removing the TPM Ê Remove the system board, see section "Removing the system board" on page 198. Ê Lay the system board on a soft, antistatic surface with its component side facing down. Figure 117: Removing the TPM Ê...

  • Page 192: Concluding Steps

    System board and components Figure 118: Removing the TPM spacer Ê Using a flat nose pliers, press together the hooks on the TPM spacer (1, see close-up) and remove it from the system board (2). If the TPM is to be replaced, the TPM spacer may remain on the system board.

  • Page 193: Replacing The Tpm

    System board and components 15.3.3 Replacing the TPM Field Replaceable Unit Hardware: 40 minutes (FRU) Tools: Removing the system board: – Phillips PH2 / (+) No. 2 screw driver Replacing the TPM: – Bit screw driver – TPM bit insert –...

  • Page 194: Removing The Defective Tpm

    System board and components 15.3.3.2 Removing the defective TPM Ê Remove the TPM, see section "Removing the TPM" on page 191. Ê Leave the TPM spacer on the system board when removing the defective TPM. 15.3.3.3 Installing the new TPM The TPM spacer is already present on the system board.

  • Page 195: Replacing The System Board

    System board and components 15.4 Replacing the system board Field Replaceable Unit Hardware: 50 minutes (FRU) Software: 10 minutes Tools: Replacing the system board: – Phillips PH2 / (+) No. 2 screw driver – Magnifying glass for inspecting CPU socket springs (recommended) Replacing the TPM: –...
  • Page 196 System board and components Note on TPM The system board can be equipped with an optional TPM (Trusted Platform Module). This module enables third party programs to store key information (e. g. drive encryption using Windows Bitlocker Drive Encryption). If the customer is using TPM functionality, the TPM has to be removed from the defective system board and connected to the new system board.

  • Page 197: Preliminary Steps

    System board and components 15.4.1 Preliminary steps Ê Backup the BIOS settings manually. "Suspending BitLocker functionality" on page 61 Ê "Shutting down the server" on page 44 Ê "Disconnecting the power cord" on page 45 Ê Ê Disconnect all external cables. "Getting access to the component"...

  • Page 198: Removing The System Board

    System board and components 15.4.2 Removing the system board Ê Disconnect all cables from the system board. Figure 119: Removing the screws Ê Remove five screws from the chassis (see circles). Figure 120: Pulling out the system board tray Ê Pull the system board tray out of the chassis. Upgrade and Maintenance Manual TX1310 M3...
  • Page 199 System board and components Figure 121: Positions of the screws Ê Remove eight screws from the system board (see circles). Ê Use both hands to carefully pull the plug shells out of the connector panel and remove the system board from its tray. CAUTION! Always hold the system board with both hands! Never lift the system board one-sided or at a heat sink, because the...

  • Page 200: Installing The System Board

    System board and components 15.4.3 Installing the system board Ê Check the settings on the new system board (see section "Onboard settings" on page 231). Ê Insert the system board by holding it at a slight angle. Slide the connectors into the connector panel.
  • Page 201 System board and components Figure 123: Pushing the system board tray Ê Push the system board tray back into the chassis. Figure 124: Fastening the screws Ê Fasten the system board tray to the chassis with five screws. Upgrade and Maintenance Manual TX1310 M3...

  • Page 202: Concluding Steps

    System board and components Ê Remove the protective cover from the CPU socket of the new system board, see section "Removing the protective cover" on page 151. Ê Remove the CPU from the defective system board, see section "Removing the CPU" on page 135.
  • Page 203 System board and components "Switching on the server" on page 57 Ê When the system is powered on after a CPU has been replaced or upgraded, the message "CPU has been changed" appears: This only indicates that the CPU configuration has been altered. There is no technical problem.
  • Page 204 System board and components Upgrade and Maintenance Manual TX1310 M3...

  • Page 205: Cables

    Cables 16.1 Overview cables No. Part number Description From - to Basic System board to HDD1 and HDD2 T26139-Y4023-V203 HDD cable (power and data) System board to HDD3, HDD4 and ODD (power and data), T26139-Y4023-V205 Power / SATA 2 cable System board to RDX (only power) Optional...

  • Page 206: Cabling Plans

    Cables 16.2 Cabling plans Power Supply 250W E563-V50 System Board D3521-A PWR HDD bottom PWR HDD-ODD USB_3/4x FAN (SYS) FAN (OEM) FAN (CPU) SATA 5 SATA 3 SATA 4 SATA 1 SATA 2 Figure 125: Cabling standard PSU Upgrade and Maintenance Manual TX1310 M3...
  • Page 207 Cables System Board D3521-A PWR HDD bottom PWR HDD-ODD USB_3/4x Front FAN Front FAN FAN (SYS) FAN (OEM) Rear FAN FAN (CPU) Rear FAN CPU FAN CPU FAN SATA 5 SATA 3 SATA 4 SATA 1 SATA 2 Figure 126: Cabling fans Upgrade and Maintenance Manual TX1310 M3...
  • Page 208 Cables System Board D3521-A System Board D3521-A PWR HDD bottom PWR HDD bottom Backup DRV SATA PWR HDD-ODD PWR HDD-ODD USB_3/4x USB_3/4x Ultra Slim SATA FAN (SYS) FAN (SYS) FAN (OEM) FAN (OEM) SATA HDD3 SATA FAN (CPU) FAN (CPU) SATA HDD4 SATA SATA 5...
  • Page 209 Cables System Board D3521-A System Board D3521-A PWR HDD bottom PWR HDD bottom Backup DRV SATA PWR HDD-ODD PWR HDD-ODD USB_3/4x USB_3/4x Ultra Slim SATA FAN (SYS) FAN (SYS) FAN (OEM) FAN (OEM) SATA HDD3 SATA HDD4 SATA SATA FAN (CPU) FAN (CPU) SATA HDD4 SATA HDD3...
  • Page 210 Cables System Board D3521-A System Board D3521-A PWR HDD bottom PWR HDD bottom Backup DRV SATA PWR HDD-ODD PWR HDD-ODD USB_3/4x USB_3/4x Ultra Slim SATA FAN (SYS) FAN (SYS) FAN (OEM) FAN (OEM) SATA HDD4 SATA HDD3 SATA SATA FAN (CPU) FAN (CPU) SATA HDD3 SATA HDD4...
  • Page 211 Cables System Board D3521-A PWR HDD bottom Backup DRV SATA PWR HDD-ODD USB_3/4x Ultra Slim P5/5 SATA FAN (SYS) FAN (OEM) SATA HDD3 P3/3 SATA FAN (CPU) SATA HDD4 P2/4 SATA SATA 5 P8/5 SATA 3 P7/3 SATA HDD2 SATA SATA 4 P6/4 SATA 1...
  • Page 212 Cables System Board D3521-A System Board D3521-A PWR HDD bottom PWR HDD bottom Backup DRV SATA PWR HDD-ODD PWR HDD-ODD USB_3/4x USB_3/4x Ultra Slim SATA FAN (SYS) FAN (SYS) FAN (OEM) FAN (OEM) SATA HDD4 SATA HDD3 SATA SATA FAN (CPU) FAN (CPU) SATA HDD3 SATA HDD4...
  • Page 213 Cables System Board D3521-A PWR HDD-ODD USB_3/4x Serial Port COM1 Serial Port FAN (SYS) FAN (OEM) FAN (CPU) SATA 5 SATA 3 SATA 4 SATA 1 SATA 2 Figure 132: Cabling Serial Port Upgrade and Maintenance Manual TX1310 M3...

  • Page 214: Replacing Cables

    Cables 16.3 Replacing cables The following steps are only required in case of a defective cable. 16.3.1 Replacing the system cable (accessible drives / top HDD cage) Upgrade and Repair Unit Hardware: 5 minutes (URU) Tool: tool-less 16.3.1.1 Preliminary steps "Shutting down the server"...
  • Page 215 Cables Figure 133: Removing the connectors from accessible drives Ê Pinch the left side of the connector (1) and remove it from the ODD back plate (2). Ê Remove the connector from the backup drive (3). Figure 134: Removing the connectors from top HDD cage Ê...

  • Page 216: Installing The New System Cable

    Cables 16.3.1.3 Installing the new system cable Ê Install the new cable to the top HDD cage and accessible drives. Ê Connect the cables to the system board. For further cabling information, please refer to section "Cabling plans" on page 206.

  • Page 217: Replacing The Hdd Cable (Bottom Hdd Cage)

    Cables 16.3.2 Replacing the HDD cable (bottom HDD cage) Upgrade and Repair Unit Hardware: 5 minutes (URU) Tool: Phillips PH2 / (+) No. 2 screw driver 16.3.2.1 Preliminary steps "Shutting down the server" on page 44 Ê "Disconnecting the power cord" on page 45 Ê...
  • Page 218 Cables Figure 136: Removing the HDD cage bottom Ê Pull the bottom HDD cage to the front as far as possible, lift it over the cant and remove it. Figure 137: Removing the defective cable Ê Pinch the sides of the connector (1) and remove it from the bottom HDD cage (2).

  • Page 219: Installing The New Hdd Cable

    Cables Figure 138: Removing the screw Ê Remove the screw (see close-up). Ê Remove the defective cable from the bottom HDD cage. 16.3.2.3 Installing the new HDD cable When installing the bottom HDD cage into the chassis, make sure that the chassis is in upright position.

  • Page 220: Concluding Steps

    Cables Ê Fasten the bottom HDD cage with two screws. Ê If applicable, install HDD1 and HDD2, see section "Installing a 3.5-inch HDD" on page Ê Push the system board tray back into the chassis, see section "Installing the system board" on page 200.

  • Page 221: Appendix

    Appendix 17.1 Mechanical overview 17.1.1 Server front Figure 140: Front side Pos. Component Ultra slim ODD RDX backup drive (optional) On/Off button Front USB connectors (2x) Upgrade and Maintenance Manual TX1310 M3...

  • Page 222: Server Rear

    Appendix 17.1.2 Server rear Figure 141: Rear side with PSU Pos. Component Standard PSU USB 2.0 connectors (2x) Video connector (Display port) USB 3.0 connectors (4x) Optional expansion cards (4x) Serial connector (optional) LAN connector Upgrade and Maintenance Manual TX1310 M3...

  • Page 223: Server Interior

    Appendix 17.1.3 Server interior Figure 142: Interior Pos. Component HDD 2 Expansion card slots TPM board (if installed) HDD 1 Fan SYS Memory modules HDD 4 HDD 3 Accessible drive bays Fan OEM Upgrade and Maintenance Manual TX1310 M3...

  • Page 224: Connectors And Indicators

    Appendix Pos. Component CPU / CPU heat sink / CPU fan System board 17.2 Connectors and indicators 17.2.1 Connectors on the system board Figure 143: Internal connectors of system board D3521 Upgrade and Maintenance Manual TX1310 M3...
  • Page 225 Appendix No. Print Description Fan (OEM) Rear fan connector PWR 12V PSU Power Fan (CPU) CPU fan connector SATA PWR SATA Power connector Front panel connector USB 3.0 USB 3.0 connector SATA 3 SATA 3 connector USB 3/4 USB connector for backup drives SATA 5 SATA 5 connector SATA 4...

  • Page 226: Server Front

    Appendix 17.2.2 Server front 17.2.2.1 Indicators on the front panel Figure 144: Indicators on the front panel Pos. Label Indicator Status Description The server is switched off. Power-on indicator The server is switched on. white on HDD/SSD white activity Data access in progress. flashing indicator Upgrade and Maintenance Manual...

  • Page 227: Indicator On The Drives

    Appendix 17.2.2.2 Indicator on the drives ODD activity indicator Figure 145: Indicator on the ODD Pos. Indicator Status Description The ODD is inactive. ODD activity indicator green on The storage medium is being accessed. There are also ODDs without activity indicators. Upgrade and Maintenance Manual TX1310 M3...
  • Page 228 Appendix RDX drive Power-on indicator Figure 146: Indicator on the RDX drive Pos. Indicator Status Description Drive is not powered on. green on Drive is ready and working properly. green flashing Drive is ejecting media. RDX has detected a drive failure RDX drive amber on condition.

  • Page 229: Server Rear

    Appendix 17.2.3 Server rear 17.2.3.1 Connectors on the I/O panel Figure 147: Connectors on the I/O panel LAN connector USB 3.0 connectors (4x) Serial connector (optional) Video connector (DisplayPort) USB 2.0 connectors (2x) The chipset offers two integrated USB 2.0 Rate Matching Hubs (RMHs). That enables lower power requirements and manages the transition of the communication data rate from the high speed of the host controller to the lower speed of USB full speed / low speed devices.

  • Page 230: Indicators On The I/O Panel

    Appendix 17.2.3.2 Indicators on the I/O panel Figure 148: Indicators on the I/O panel: LAN indicators Pos. Indicator Status Description green on A LAN connection has been established. link/transfer LAN is not connected. indicator green flashing LAN data transfer is in progress yellow on Data traffic at a transfer rate of 1 Gbit/s LAN speed...

  • Page 231: Onboard Settings

    Appendix 17.3 Onboard settings Pin 2 Pin 1 Figure 149: Jumper Setting Status Description Default: Password Clear and Recovery BIOS disabled Pin 1 Pin 2 Jumper RCVR: Recovery BIOS enabled settings Pin 1 Pin 2 PWD-CLR: Password Clear enabled Pin 1 Pin 2 When the CMOS battery is removed from a system board, the password set by customers is kept and also other CMOS settings are restored except date/time.

  • Page 232: Minimum Startup Configuration

    Appendix 17.4 Minimum startup configuration Field Replaceable Units (FRU) If the server does not start up or other problems occur, it may be necessary to take the system down to its most basic configuration in order to isolate the defective component. The minimum startup configuration consists of the following components and cables: Component...
  • Page 233 Appendix CAUTION! Since the system fan is not included in the minimum startup configuration, the server must be shut down immediately after the diagnostic process is complete (POST phase has been passed). The minimum startup configuration must be used exclusively for diagnostic purposes by maintenance personnel, never in daily operation! Upgrade and Maintenance Manual...
  • Page 234 Appendix Upgrade and Maintenance Manual TX1310 M3...

Table of Contents