Fujitsu PRIMERGY TX1310 M3 Operating Manual

Fujitsu PRIMERGY TX1310 M3 Operating Manual

Hide thumbs Also See for PRIMERGY TX1310 M3:

Advertisement

Operating Manual - English
FUJITSU Server PRIMERGY TX1310 M3
Operating Manual
January 2018

Advertisement

Table of Contents
loading

Summary of Contents for Fujitsu PRIMERGY TX1310 M3

  • Page 1 Operating Manual - English FUJITSU Server PRIMERGY TX1310 M3 Operating Manual January 2018...
  • Page 2 – The contents of this manual may be revised without prior notice. – Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual. – No part of this manual may be reproduced in any without the prior written permission of Fujitsu.
  • Page 3 Before reading this manual For your safety This manual contains important information for safely and correctly using this product. Carefully read the manual before using this product. Pay particular attention to the accompanying manual "Safety Notes and Regulations" and ensure these safety notes are understood before using the product.
  • Page 4 Please consult the sales staff of Fujitsu if intending to use this product for high safety use. Measures against momentary voltage drop This product may be affected by a momentary voltage drop in the power supply caused by lightning.
  • Page 5: Table Of Contents

    Contents Introduction ......9 Concept and target groups for this manual ..9 Documentation overview .
  • Page 6 Contents Access to the drives ..... . . 47 Controls and indicators ..... 49 6.2.1 Server front .
  • Page 7 Contents 8.12 Optical drive cannot read data ....67 Operating Manual TX1310 M3...
  • Page 8 Contents Operating Manual TX1310 M3...
  • Page 9: Introduction

    Introduction The PRIMERGY TX1310 M3 server is an Intel-based server for workgroups and small networks. The server is suitable for use as a file server and also as an application, information or Internet server. Thanks to its highly developed hardware and software components, the PRIMERGY TX1310 M3 server offers a high level of data security and availability.
  • Page 10: Documentation Overview

    Introduction Documentation overview More information on your PRIMERGY TX1310 M3 can be found in the following documents: – "Quick Start Hardware - FUJITSU Server PRIMERGY TX1310 M3" – "ServerView Quick Start Guide" – "Safety Notes and Regulations" manual " 安全上のご注意 " for Japan –...
  • Page 11: Notational Conventions

    Introduction Further sources of information: – ServerView Suite Glossary – Manual for the monitor – Documentation for the boards and drives – Operating system documentation – Information files in your operating system Notational conventions The following notational conventions are used in this manual: indicates commands or menu items.
  • Page 12 Introduction Operating Manual TX1310 M3...
  • Page 13: Functional Overview

    This section provides information on the features and technical data of the PRIMERGY TX1310 M3 server. For information on key characteristics and layout of the system board, see "D3521 BIOS Setup Utility for FUJITSU Server PRIMERGY TX1310 M3 Reference Manual".
  • Page 14 Functional overview – If a failure occurs, please inform your service about the TPM activation before it takes any action, and be prepared to provide them with your backup copies of the TPM content. Hard disk drives (HDDs) Up to four 3.5-inch SATA HDDs, each with a maximum height of 1 inch, are built into the drive cages.
  • Page 15 When memory data is accessed, 1-bit errors are identified in the main memory and automatically corrected with the error correcting code (ECC) method. The PDA (Prefailure Detection and Analysis) technology from Fujitsu analyzes and monitors all components that are critical for system reliability.
  • Page 16 The Flash EPROM program supplied with the Fujitsu utilities supports a fast BIOS update. ServerView Remote Management ServerView Remote Management is the remote management solution from Fujitsu for PRIMERGY servers.
  • Page 17: Server Specification

    Functional overview Server specification This section explains the specifications for the server. The specifications for this server are liable to be updated without any notice. Please be forewarned. System Board System board type D3521 ® Chipset Intel C236 ® CPU quantity and type 1x Intel Dual Core CPUs or 1x Quad Core CPUs...
  • Page 18 Functional overview Onboard or integrated controllers Serial ATA total RAID Controller RAID level 0, 1, 10 ® ® SATA Controller Embedded in Intel Chipset C236 ® LAN Controller Single chip GbE Ethernet controller Intel i219LM onboard, 1 x 10/100/1000 Mbit/s, PXE-Boot by LAN via PXE- Server, Teaming supported Trusted Platform Infineon V1.2 / V2.0 compliant (option)
  • Page 19 Functional overview Dimensions / Weight Floorstand (W x D x H) 179.95 x 312.9 x 373.95 mm Weight max. 12 kg (depending on configuration) Ventilation clearance At least 200 mm on the front and rear. Ambient conditions Environment class 3K2 EN 60721 / IEC 721 Part 3-3 Environment class 2K2 EN 60721 / IEC 721 Part 3-2...
  • Page 20 Functional overview Compliance with standards Product safety and ergonomics International IEC 60950-1 2ed; am1 + am2 Europe Safety EN 60950-1 2ed; A1 + A2 + A11 + A12 EN 62479 EN 62311 Ergonomics ISO 9241-3 EN 2941-3 EK1-ITB2000:2013 USA / Canada CSA-C22.2 No.
  • Page 21 Functional overview CAUTION! This device meets the requirements of Class A CISPR 22/32. This device can cause radio interference in residential areas. Operating Manual TX1310 M3...
  • Page 22 Functional overview Operating Manual TX1310 M3...
  • Page 23: Installation Steps, Overview

    Details on how to operate the ServerView Installation Manager, as well as some additional information, are included in the "ServerView Suite Installation Manager" user’s guide (on the Fujitsu manuals server under x86 Servers - Software - ServerView Suite - Server Installation and Deployment).
  • Page 24 You will find more information on installing the server remotely or locally in the "ServerView Suite Installation Manager" user’s guide (on the Fujitsu manuals server under x86 Servers - Software - ServerView Suite - Server Installation and Deployment). Operating Manual...
  • Page 25: Important Information

    Important information Depending on your server or the installed options some information is not valid for your server. CAUTION! Before installing and starting up a server, please observe the safety instructions listed in the following section. This will help you to avoid making serious errors that could impair your health, damage the server and endanger the data base.
  • Page 26 Important information Before starting up During installation and before operating the server, observe the instructions ● on environmental conditions for your server. If the server is brought in from a cold environment, condensation may form ● both inside and on the outside of the server. Wait until the server has acclimatized to room temperature and is absolutely dry before starting it up.
  • Page 27 Important information Always connect the server and the attached peripheral devices to the same ● power circuit. Otherwise you run the risk of losing data if, for example, the server is still running but a peripheral device (e.g. memory subsystem) fails during a power outage.
  • Page 28 Important information The warranty is void if the server is damaged during installation or ● replacement of server expansions. Only set screen resolutions and refresh rates that are specified in the ● operating manual for the monitor. Otherwise, you may damage your monitor. If you are in any doubt, contact your sales outlet or customer service center.
  • Page 29 Important information The battery used in this server may present a fire or chemical burn hazard if ● mistreated. Do not disassemble, heat about 100 °C (212F), or incinerate the battery. Replace the lithium battery on the system board in accordance with the ●...
  • Page 30 Important information Do not pull on, press hard, or otherwise handle the CD/DVD/BD tray ● roughly. Do not disassemble the optical disk drive. ● Before use, clean the optical disk tray using a soft, dry cloth. ● As a precaution, remove disks from the optical disk drive when the ●...
  • Page 31 Important information You can prevent damage from the optical disk drive and the CDs/DVDs/BDs, as well as premature wear of the disks, by observing the following suggestions: – Only insert disks in the drive when needed and remove them after use.
  • Page 32 Important information The circuit boards and soldered parts of internal options are exposed and ● can be damaged by static electricity. To ensure reliable protection, you must wear an earthing band on your wrist when working with ESD modules and connect it to an unpainted, conducting metal part of the server.
  • Page 33 Important information When connecting and disconnecting cables, observe the relevant ● instructions in the "Important Information" chapter of the technical manual for the corresponding rack. The technical manual is supplied with the corresponding rack. When installing the rack, make sure that the anti-tilt mechanism is ●...
  • Page 34: Ce Conformity

    Important information CE conformity The system complies with the requirements of European Regulations. Find the CE declaration on certificate portal: https://sp.ts.fujitsu.com/sites/certificates/default.aspx To open the CE declaration applicable for your system, proceed as follows: Ê Select Industry Standard Servers. Ê Select your model, e.g. Rack server.
  • Page 35: Fcc Class A Compliance Statement

    Consult the dealer or an experienced radio/TV technician for help. ● Fujitsu is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Fujitsu. The correction of interferences caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.
  • Page 36: Environmental Protection

    Important information Environmental protection Environmentally-friendly product design and development This product has been designed in accordance with the Fujitsu standard for "environmentally friendly product design and development". This means that key factors such as durability, selection and labeling of materials, emissions, packaging, ease of dismantling and recycling have been taken into account.
  • Page 37 Further information can be found at: http://ts.fujitsu.com/recycling Details regarding the return and recycling of devices and consumables within Europe can also be found in the "Returning used devices" manual, via your local Fujitsu branch, or at: http://ts.fujitsu.com/recycling Operating Manual TX1310 M3...
  • Page 38 Important information Operating Manual TX1310 M3...
  • Page 39: Hardware Installation

    Hardware installation CAUTION! Follow the safety instructions in the chapter "Important information" ● on page Do not expose the server to extreme environmental conditions (see ● "Ambient conditions" on page 19). Protect the server from dust, humidity and heat. Make sure that the server is acclimatized for the time indicated in this ●...
  • Page 40: Unpacking The Server

    Ê Remove all scratching protection foils from the front panel, HDD frames, Fujitsu and PRIMERGY logo, VGA dummy and ODD dummy in case they are still sticked to the server system. Operating Manual...
  • Page 41: Setting Up The Server

    Hardware installation Setting up the server Ê Transport the server to the place where you want to set it up. Ê Unpack the server (see section "Unpacking the server" on page 40). Ê Set up the server. CAUTION! – The device must be protected from direct sunlight. –...
  • Page 42: Connecting Devices To The Server

    The connectors for external devices are on the front and rear of the server. The additional connectors available on your server depend on the expansion cards installed. For further information refer to the “FUJITSU Server PRIMERGY TX1310 M3 Upgrade and Maintenance Manual”. The standard connectors are...
  • Page 43 Hardware installation Figure 3: Connector panel on the rear side 1 LAN connector 2 USB 3.0 connectors (x4) 3 Serial connector (optional) 4 Video connector (Display Port) 5 USB 2.0 connectors (x2) Some of the devices that can be connected may require special drivers (see the documentation for the connected device).
  • Page 44: Connecting The Server To The Mains

    Hardware installation Connecting the server to the mains The server is equipped with an integrated PSU. CAUTION! The server is automatically set to a mains voltage in the range 100 V - 240 V. You may only operate the server if its rated voltage range corresponds to the local mains voltage.
  • Page 45 Hardware installation Disconnecting cables Ê Turn off all power and equipment switches. Ê Disconnect all power plugs from the properly grounded power outlets. Ê Unplug all data communication cables from the utility sockets. Ê Disconnect the relevant cables from the server and all the peripherals. For connecting or disconnecting LAN cables, the server does not need to be powered off.
  • Page 46 Hardware installation Operating Manual TX1310 M3...
  • Page 47: Starting Up And Operation

    Ê Open the side cover (2). Ê Remove the side cover (3). The following procedure is described in detail in the "FUJITSU Server PRIMERGY TX1310 M3 Upgrade and Maintenance Manual". Ê Remove the HDD cage cover by pulling it backwards beginning at its right side (4).
  • Page 48 Starting up and operation Ê Open the HDD cage door by swivelling it downwards. CAUTION! The HDD cage door can only be opened after the side cover has been removed because of the anti-theft lock. Ê Remove the HDD cage door. You now have access to the HDDs.
  • Page 49: Controls And Indicators

    Starting up and operation Controls and indicators 6.2.1 Server front Figure 5: Front panel 6.2.1.1 Controls on the front panel Pos. Label Button Function Used to switch the server on or off. If the system is running an ACPI- On/Off button compliant operating system, pressing the On/Off button will perform a graceful shutdown.
  • Page 50: Indicators On The Drives

    Starting up and operation 6.2.1.3 Indicators on the drives Optical drive activity indicator Figure 6: Indicator on the optical drive Pos. Indicator Status Description The optical drive is inactive. ODD activity indicator green on The storage medium is being accessed. There are also ODDs without activity indicators.
  • Page 51 Starting up and operation RDX drive activity indicator Figure 7: Indicator on the RDX drive Pos. Indicator Status Description Drive does not have power. Steady green Drive is ready and working properly. Blinking green Drive is ejecting media. RDX has detected a drive fault RDX drive Steady amber condition.
  • Page 52: Server Rear

    Starting up and operation 6.2.2 Server rear 6.2.2.1 Indicators on the I/O panel LAN indicators Figure 8: Indicators on the connector panel: LAN indicators Pos. Indicator Status Description green on A LAN connection has been established. link/transfer LAN is not connected. indicator green flashing LAN data transfer is in progress yellow on...
  • Page 53: Switching The Server On And Off

    "Safety Precautions".When operating the device outside of this operating environment, the server may operate improperly, damage data etc.Furthermore, Fujitsu cannot be held responsible for any related damage, malfunction, or loss of data, etc. Be sure to wait for 10 seconds or more after shutdown before turning ●...
  • Page 54 Starting up and operation Switching the server on Figure 9: On/Off button of the server – Starting up for the first time: For Japan, please refer to " はじめにお読みください ". Ê Press the On/Off button (1) (see figure 9 on page 54).
  • Page 55 Starting up and operation If the operating system does not switch off the server automatically, press the On/Off button for at least four seconds and/or send a corresponding control signal. CAUTION! There is a risk that data may be lost. Other Power On/Off options The usage of Power On/Off options requires the installation of ServerView Agents.
  • Page 56: Configuring The Server

    The controller has its own configuration utility. For further information, refer to the “Embedded MegaRAID Software User’s Guide” (on the Fujitsu manuals server under x86 Servers - Expansion Cards - Storage Adapters - LSI Configuration Software - Embedded MegaRAID Software).
  • Page 57: Configuring The Server And Installing The Operating System With The Serverview Installation Manager

    This configuration is detected automatically. Descriptions of operating systems not covered in the RAID controller manual are provided in the corresponding readme files under: http://www.fujitsu.com/global/services/computing/server/ia/driver/index.html For Japan: http://www.fujitsu.com/jp/products/computing/servers/primergy/downloads/ To find out how to operate the ServerView Installation Manager and for further information, refer to the associated manual.
  • Page 58: Configuring The Server And Installing The Operating System Without The Serverview Installation Manager

    Starting up and operation 6.4.3 Configuring the server and installing the operating system without the ServerView Installation Manager Configure onboard SATA controller Configure the controller, see section "Configuring the onboard SATA controller" on page Installing the operating system Ê Insert the CD/DVD for the operating system you want to install. Ê...
  • Page 59: Cleaning The Server

    Starting up and operation Cleaning the server CAUTION! Switch off the server and disconnect the power plugs from the properly grounded power outlets. Do not clean any interior parts yourself; leave this job to a service technician. Do not use any cleaning agents that contain abrasives or may corrode plastic.
  • Page 60 Starting up and operation Operating Manual TX1310 M3...
  • Page 61: Property And Data Protection

    Property and data protection To prevent it being removed from its location, the server can be secured to a fixed object with a steel cable running through a clip on the back. To protect the system and data internally against unauthorized access, you can activate the security functions of the BIOS Setup.
  • Page 62 Property and data protection Operating Manual TX1310 M3...
  • Page 63: Troubleshooting And Tips

    Troubleshooting and tips CAUTION! Follow the safety instructions in the "Safety notes and regulations" manual or " 安全上のご注意 " and in chapter "Important information" on page If a fault occurs, attempt to resolve it using the measures described: – in this chapter, –...
  • Page 64: Server Switches Itself Off

    Troubleshooting and tips Server switches itself off Server Management has detected an error Ê Check the error list of System Event Log in ServerView Operations Manager, and attempt to eliminate the error. Screen remains blank Monitor is switched off Ê Switch on your monitor. Screen has gone blank Ê...
  • Page 65: Flickering Stripes On Monitor Screen

    Troubleshooting and tips Flickering stripes on monitor screen CAUTION! Switch off the server immediately. Risk of damaging the server. Monitor does not support the set horizontal frequency Ê Find out which horizontal frequency your monitor screen supports. You will find the horizontal frequency (also known as line frequency or horizontal deflection frequency) in the documentation for your monitor.
  • Page 66: Incorrect Date And Time

    If the date and time are still wrong after the server has been switched off and back on again, replace the lithium battery (for a description refer to the "FUJITSU Server PRIMERGY TX1310 M3 Upgrade and Maintenance Manual") or contact our customer service team.
  • Page 67: Temperature Warning

    Troubleshooting and tips 8.10 Temperature warning A temperature warning will be send to the hardware event log and OS event log, or ServerView issues a notification of a temperature warning such as by a popup message The above log is output or the above notification is issued by ServerView when the ambient temperature is within 30 to 35°C, which is near the upper limit of the temperature boundaries (10 to 35°C).
  • Page 68 Troubleshooting and tips Operating Manual TX1310 M3...

Table of Contents