Fujitsu PRIMERGY TX1310 M1 Upgrade And Maintenance Manual
  1. Manuals
  2. Brands
  3. Fujitsu Manuals
  4. Server
  5. PRIMERGY TX1310 M1
  6. Upgrade and maintenance manual

Fujitsu PRIMERGY TX1310 M1 Upgrade And Maintenance Manual

Hide thumbs Also See for PRIMERGY TX1310 M1:
Table of Contents

Advertisement

Quick Links

See also: Operating Manual
Upgrade and Maintenance Manual - English
FUJITSU Server PRIMERGY TX1310 M1
Upgrade and Maintenance Manual
Edition May 2014

Advertisement

Table of Contents
loading

Related Manuals for Fujitsu PRIMERGY TX1310 M1

Summary of Contents for Fujitsu PRIMERGY TX1310 M1

  • Page 1 Upgrade and Maintenance Manual - English FUJITSU Server PRIMERGY TX1310 M1 Upgrade and Maintenance Manual Edition May 2014...

  • Page 2: Copyright And Trademarks

    – The contents of this manual may be revised without prior notice. – Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual. – No part of this manual may be reproduced in any form without the prior written permission of Fujitsu.
  • Page 3 Before reading this manual For your safety This manual contains important information for safely and correctly using this product. Carefully read the manual before using this product. Pay particular attention to the accompanying manual "Safety Notes and Regulations" and ensure these safety notes are understood before using the product.
  • Page 4 Please consult the sales staff of Fujitsu if intending to use this product for high safety use. Measures against momentary voltage drop This product may be affected by a momentary voltage drop in the power supply caused by lightning.

  • Page 5: Version History

    Version history Version history Issue number Reason for update 1.0 / 20.5.2014 Initial release Upgrade and Maintenance Manual TX1310 M1...
  • Page 6 Version history Upgrade and Maintenance Manual TX1310 M1...

  • Page 7: Table Of Contents

    Contents Introduction ......15 Notational conventions ....17 Before you start .
  • Page 8 Contents 4.4.3 Removing the front cover ..... 46 Reassembling ......47 4.5.1 Installing the front cover .
  • Page 9 Contents Power supply ......79 Replacing the power supply unit ....80 6.1.1 Preliminary steps .
  • Page 10 Contents 8.3.1 Preliminary steps ......109 8.3.2 Removing the defective system fan 1 ....109 8.3.3 Installing the new system fan 1 .
  • Page 11 Contents 10.3.1 Preliminary steps ......138 10.3.2 Removing a memory module ....138 10.3.3 Concluding steps .
  • Page 12 Contents 12.2.3.1 Preparing the optical disk drive ....164 12.2.3.2 Installing the optical disk drive ....166 12.2.4 Installing a slimline optical disk drive (ODD) .
  • Page 13 Contents System board and components ....193 14.1 Basic information ..... . . 193 14.2 Replacing the CMOS battery .
  • Page 14 Contents Appendix ......221 16.1 Mechanical overview ..... 221 16.1.1 Server front .

  • Page 15: Introduction

    Introduction This Upgrade and Maintenance Manual provides instructions for the following procedures: Upgrading the server configuration by adding optional hardware ● components Upgrading the server configuration by replacing existing hardware ● components with superior ones. Replacing defective hardware components ● This manual focuses on on-site maintenance tasks.
  • Page 16 Introduction Different versions for TX1310 M1 The PRIMERGY TX1310 M1 is available in different versions. Your base unit may not have all functions described in this manual. The following table provides an overview of the different features: System board D3219-Axx...

  • Page 17: Notational Conventions

    Introduction Notational conventions The following notational conventions are used in this manual: indicates commands or menu items Text in italics indicates system output fixed font indicates text to be entered by the user semi-bold fixed font "Quotation marks" indicate names of chapters and terms that are being emphasized describes activities that must be performed in the order Ê...
  • Page 18 Introduction Upgrade and Maintenance Manual TX1310 M1...

  • Page 19: Before You Start

    Japanese market: http://jp.fujitsu.com/platform/server/primergy/system/ Please contact your local Fujitsu customer service partner for details on how to order expansion kits or spare parts. Use the Fujitsu Illustrated Spares Catalog to identify the required spare part and obtain technical data and order information.

  • Page 20: Classification Of Procedures

    At the beginning of each procedure, the involved unit type is indicated by one of the symbols introduced in this section. Please ask your local Fujitsu service center for more detailed information. 2.1.1 Customer Replaceable Units (CRU) Customer Replaceable Units (CRU) Customer Replaceable Units are intended for customer self service.

  • Page 21: Upgrade And Repair Units (Uru)

    Before you start 2.1.2 Upgrade and Repair Units (URU) Upgrade and Repair Units (URU) Upgrade and Repair Units are non hot-plug components that can be ordered separately to be installed as options (Upgrade Units) or are available to the customer through customer self service (Repair Units). Server management error messages will report defective Upgrade and Repair Units.

  • Page 22: Field Replaceable Units (Fru)

    Maintenance procedures involving Field Replaceable Units must be performed exclusively by Fujitsu service personnel or technicians trained by Fujitsu. Please note that unauthorized interference with the system will void the warranty and exempt the manufacturer from all liability. Components that are handled as Field Replaceable Units –...

  • Page 23: Average Task Duration

    Before you start Average task duration Hardware: 10 minutes The average task duration including preliminary and concluding steps is indicated at the beginning of each procedure next to the procedure class. Refer to table 1 on page 23 for an overview of steps taken into account for calculating the average task duration: Step included...

  • Page 24: Tools You Need At Hand

    Before you start Tools you need at hand When preparing the maintenance task, ensure that all required tools are available according to the overview below. You will find a list of required tools at the beginning of each procedure. Screw driver / Screw Usage Type...

  • Page 25: Documents You Need At Hand

    For the Japanese market please use the following address: http:/jp.fujitsu.com/platform/server/primergy/manual/ Document Description "Quick Start Hardware - Quick installation poster for initial operation, FUJITSU Server PRIMERGY available online TX1310 M1" leaflet "ServerView Quick Start Guide" Information on initial server setup and " ServerView クイックスタート...
  • Page 26 Document Description Spare parts identification and information system (EMEA market only), available for online use or download (Windows OS) at Illustrated Spares catalog http://manuals.ts.fujitsu.com/illustrated_spares or from the CSS component view of the ServerView Operations Manager. Glossary available online "Warranty" manual...

  • Page 27: Important Information

    Important information CAUTION! Before installing and starting up a device, please observe the safety instructions listed in the following section. This will help you to avoid making serious errors that could impair your health, damage the device and endanger the data base. Safety instructions The following safety instructions are also provided in the manual "Safety Notes and Regulations"...
  • Page 28 Important information Wait until the device has acclimatized to room temperature and is absolutely dry before starting it up. Material damage may be caused to the device if this requirement is not observed. Transport the device only in the original packaging or in packaging that ●...
  • Page 29 Important information Ethernet cabling has to comply with EN 50173 and EN 50174-1/2 standards ● or ISO/IEC 11801 standard respectively. The minimum requirement is a Category 5 shielded cable for 10/100 Ethernet, or a Category 5e cable for Gigabit Ethernet. Route the cables in such a way that they do not create a potential hazard ●...
  • Page 30 Important information Do not damage or modify internal cables or devices. Doing so may cause a ● device failure, fire, or electric shock and will void the warranty and exempt the manufacturer from all liability. Devices inside the server remain hot after shutdown. Wait for a while after ●...
  • Page 31 Important information Working with optical disk drives and media When working with optical disk drives, these instructions must be followed. CAUTION! Only use CDs/DVDs/BDs that are in perfect condition, in order to ● prevent data loss, equipment damage and injury. Check each CD/DVD/BD for damage, cracks, breakages etc.
  • Page 32 Important information Do not contaminate the CD/DVD/BD surface with fingerprints, oil, ● dust, etc. If dirty, clean with a soft, dry cloth, wiping from the center to the edge. Do not use benzene, thinners, water, record sprays, antistatic agents, or silicone-impregnated cloth. Be careful not to damage the CD/DVD/BD surface.
  • Page 33 Important information Modules with Electrostatic-Sensitive Devices Modules with electrostatic-sensitive devices are identified by the following sticker: Figure 1: ESD label When you handle components fitted with ESDs, you must always observe the following points: Switch off the system and remove the power plugs from the power outlets ●...

  • Page 34: Ce Conformity

    Important information Transporting the server Only transport the server in its original packaging or in packaging that ● protects it from impacts and jolts. For the Japanese market, transporting the device in its original packaging does not apply. Do not unpack the server until it is at its installation location. ●...

  • Page 35: Environmental Protection

    Consult the dealer or an experienced radio/TV technician for help. ● Fujitsu is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Fujitsu. The correction of interferences caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.
  • Page 36 This directive sets the framework for returning and recycling used equipment and is valid across the EU. When returning your used device, please use the return and collection systems available to you. Further information can be found at http://ts.fujitsu.com/recycling. Upgrade and Maintenance Manual TX1310 M1...
  • Page 37 Important information Details regarding the return and recycling of devices and consumables within Europe can also be found in the "Returning used devices" manual, via your local Fujitsu branch or from our recycling center in Paderborn: Fujitsu Technology Solutions Recycling Center D-33106 Paderborn Tel.
  • Page 38 Important information Upgrade and Maintenance Manual TX1310 M1...

  • Page 39: Basic Hardware Procedures

    Basic hardware procedures Using diagnostics information Use the Fujitsu ServerView Suite management software to plan the upgrade or replacement of hardware components. Please refer to the following ServerView Suite topics: – Operation – Maintenance It is recommended to prepare local maintenance tasks using remote diagnostics procedures, as described in the "ServerView Suite Local Service Concept...

  • Page 40: Shutting Down The Server

    Basic hardware procedures Shutting down the server CAUTION! For further safety information, please refer to chapter "Important information" on page Ê Inform the system administrator that the server will be shut down and put offline. Ê Terminate all applications. Figure 2: Power button on the front panel Ê...

  • Page 41: Disconnecting The Server From The Mains

    Basic hardware procedures Disconnecting the server from the mains Figure 3: Removing the power cord from the PSU cable tie Ê Pull out the locking lever on the PSU cable tie (1) and loosen the loop (2). Ê Disconnect the power cord from the PSU and remove it from the cable tie. Upgrade and Maintenance Manual TX1310 M1...

  • Page 42: Getting Access To The Component

    Basic hardware procedures Getting access to the component CAUTION! Before removing or installing covers, turn off the server and all ● peripheral devices. Also unplug all power cables from the outlet. Failure to do so can cause electric shock. In order to comply with applicable EMC regulations (regulations on ●...

  • Page 43: Removing Accessible Drives

    Basic hardware procedures 4.4.2 Removing accessible drives 4.4.2.1 Disconnecting the optical disk drive (ODD) Figure 5: Disconnecting cables from the optical disk drive Ê Disconnect all cables from the optical disk drive. Power cable connector P8 SATA cable Upgrade and Maintenance Manual TX1310 M1...

  • Page 44: Disconnecting The Backup Drive

    Basic hardware procedures 4.4.2.2 Disconnecting the backup drive Figure 6: Disconnecting cables from the backup drive Ê Disconnect all cables from the backup drive. Power adapter cable USB cable Upgrade and Maintenance Manual TX1310 M1...
  • Page 45 Basic hardware procedures Figure 7: Removing the optical disk drive and the backup drive Ê Press the locking latch in the direction of the arrow (1) and press out the optical disk drive from behind (2). Ê Remove the optical disk drive out of its bay. Ê...

  • Page 46: Removing The Front Cover

    Basic hardware procedures 4.4.3 Removing the front cover Figure 8: Removing the front cover Ê Disengage the three locking tabs on the front cover by pulling it forwards (1). Ê Carefully rotate open (2) and unhook the front cover (3). Upgrade and Maintenance Manual TX1310 M1...

  • Page 47: Reassembling

    Basic hardware procedures Reassembling CAUTION! Before attaching the covers, make sure no unnecessary parts or tools ● are left inside the server. In order to comply with applicable EMC regulations (regulations on ● electromagnetic compatibility) and satisfy cooling requirements, the server must not run while the side cover is removed.

  • Page 48: Installing The Front Cover

    Basic hardware procedures 4.5.1 Installing the front cover Figure 9: Installing the front cover Ê Hook the three tabs on the front bezel into the notches in the chassis (1). Ê Carefully close the front bezel (2). Make sure that all three locking latches properly engage (3).

  • Page 49: Installing Accessible Drives

    Basic hardware procedures 4.5.2 Installing accessible drives 4.5.2.1 Installing the optical disk drive (ODD) Figure 10: Installing the optical disk drive Ê Insert the optical disk drive into its installation bay and carefully push in until it locks in place (1). Make sure that the fixation plate is attached on the left side of the accessible drive.
  • Page 50 Basic hardware procedures Figure 11: Connecting cables to the optical disk drive Ê Connect cables to the optical disk drive. Power cable connector P8 SATA cable Upgrade and Maintenance Manual TX1310 M1...

  • Page 51: Installing The Backup Drive

    Basic hardware procedures 4.5.2.2 Installing the backup drive Figure 12: Installing the backup drive Ê Insert the backup drive into its installation bay and carefully push in until it locks in place. Make sure that the fixation plate is attached on the left side of the accessible drive.
  • Page 52 Basic hardware procedures Figure 13: Connecting cables to the backup drive Ê Connect all cables to the backup drive. Power adapter cable (connected to power cable connector P7) USB cable Upgrade and Maintenance Manual TX1310 M1...

  • Page 53: Installing The Side Cover

    Basic hardware procedures 4.5.3 Installing the side cover Figure 14: Installing the side cover Ê Hook the side cover in the bottom side cant of the chassis (1). Ê Push the side cover against the chassis until the locking mechanism engages (2).

  • Page 54: Connecting The Server To The Mains

    Basic hardware procedures Connecting the server to the mains The standard power supply unit that automatically adjusts to any mains voltage in the range of 100 VAC to 240 VAC. CAUTION! The power supply automatically adjusts to any mains voltage in the range of 100 VAC to 240 VAC.

  • Page 55: Switching On The Server

    Basic hardware procedures Switching on the server CAUTION! Before switching on the server, make sure the side cover is closed. In ● order to comply with applicable EMC regulations (regulations on electromagnetic compatibility) and to satisfy cooling requirements, the server must not run while the side cover is removed Follow the safety instructions in chapter "Important information"...

  • Page 56: Handling The Hdd Cage With System Fan 1

    Basic hardware procedures Handling the HDD cage with system fan 1 4.8.1 Removing the HDD cage Ê Remove the HDDs as described in section "Removing 3.5-inch HDDs" on page Take care, that you notice all detached cables for future reconnecting. Figure 17: Remove the screws Ê...
  • Page 57 Basic hardware procedures Figure 18: Lifting up the HDD cage Ê Push down the HDD cage to release it (1). Ê Push the HDD cage inwards (2). Ê Carefully lift up the HDD cage (3). First, disconnect the fan cable which is located under the fan before you lift up the HDD cage out of the chassis.
  • Page 58 Basic hardware procedures Figure 19: Connector for the fan 1 cable Ê Disconnect the cable from system board connector FAN1 SYS (see circle). Upgrade and Maintenance Manual TX1310 M1...

  • Page 59: Installing The Hdd Cage

    Basic hardware procedures 4.8.2 Installing the HDD cage Do not completely place down the HDD cage into the chassis. First, connect the fan cable which is located close to the HDD cage before you place down the HDD cage into the chassis. Figure 20: Connector for the fan 1 cable Ê...
  • Page 60 Basic hardware procedures Figure 21: Placing the HDD cage Ê Place down the HDD cage into the chassis (1). Ê Push the HDD cage to the front side of the chassis (2). Upgrade and Maintenance Manual TX1310 M1...
  • Page 61 Basic hardware procedures Figure 22: Recesses of the HDD cage Ê Pull up the HDD cage until the upper hooks engage in the recesses (see circles). This view is only visible, if the front cover is removed. Upgrade and Maintenance Manual TX1310 M1...
  • Page 62 Basic hardware procedures Figure 23: Remove the screws Ê Ensure that the noses engage under the guides (see circles) and all screw holes are matching. Ê Fasten the four screws (see circles) of the HDD cage. Ê Install the HDDs as described in section "Installing 3.5-inch HDDs"...

  • Page 63: Basic Software Procedures

    Basic software procedures Starting the maintenance task 5.1.1 Disabling BitLocker functionality BitLocker Drive Encryption provides protection for operating system and data drives by encrypting the contents and requiring users to authenticate their credentials to access the information. On the operating system drive, BitLocker uses the compatible Trusted Platform Module (TPM) to detect if the computer's startup process has been modified from its original state.

  • Page 64: Removing Backup And Optical Disk Media

    For further information on "forcible" tape ejection, please refer to the "Tape Facts" guide available to Fujitsu service partners from the following https address: https://partners.ts.fujitsu.com/com/service/ps/Servers/PRIMERGY/Pages/ TapeFacts.aspx...

  • Page 65: Verifying And Configuring The Backup Software Solution

    Procedures may differ depending on the backup software. For details, refer to the dedicated documentation provided separately. Further information on suitable backup software solutions and related documentation is available to Fujitsu service partners from the Fujitsu Extranet pages. 5.1.4 Note on server maintenance in a Multipath I/O...
  • Page 66 Basic software procedures Ê Burn the image to a DVD. Ê In order to create a bootable USB stick, please proceed as described in the "Local System Update for PRIMERGY Servers" user guide. Ê Before using the ServerView Update DVD or USB stick in an offline environment, properly shut down the server and disconnect all external I/O connections (like LAN or FC cables) from the system.
  • Page 67 Basic software procedures Using PrimeCollect To start PrimeCollect, proceed as follows: Ê Before using PrimeCollect in an offline environment, properly shut down the server and disconnect all external I/O connections (like LAN or FC cables) from the system. Only keep mouse, keyboard, video cable and AC power cord connected.

  • Page 68: Completing The Maintenance Task

    (EMEA market) (Japanese market) http://jp.fujitsu.com/platform/server/primergy/downloads/ Fujitsu does not assume responsibility for any damage done to the server or for the loss of any data resulting from BIOS updates. 5.2.1.1 Updating or recovering the system board BIOS BIOS flash procedure For the Japanese market, follow the instructions provided separately.

  • Page 69: Verifying And Configuring The Backup Software Solution

    Basic software procedures Option ROM can be enabled permanently (e.g. in case of a boot controller that may require frequent setup) or temporarily for one-time configuration. When permanently enabling a controllers’s Option ROM, keep in mind that only two Option ROMs can be activated in the system board BIOS at a time. Ê...

  • Page 70: Enabling Replaced Components In The System Bios

    Procedures may differ depending on the backup software. For details, refer to the dedicated documentation provided separately. Further information on suitable backup software solutions and related documentation is available to Fujitsu service partners from the Fujitsu Extranet pages. Re-enabling backup drives...
  • Page 71 Basic software procedures Ê Reset replaced components to Enable. Ê Save your changes and exit the BIOS. For detailed information on how to access the BIOS and modify settings, refer to the corresponding BIOS Setup Utility reference manual. Upgrade and Maintenance Manual TX1310 M1...

  • Page 72: Verifying The System Time Settings

    Basic software procedures 5.2.5 Verifying the system time settings This task only applies to Linux environments. Ê After replacing the system board, ask the system administrator whether the RTC or UTC time standard is to be used as system time. If the system time (RTC) is set to UTC, the SEL (System Event Log) time stamps may differ from the local time.

  • Page 73: Updating The Nic Configuration File In A Linux Environment

    Basic software procedures Ê Select the message type(s) you want to display: – Critical events – Major events – Minor events – Informational events For detailed information on how to view and sort the SEL using ServerView Operations Manager, refer to the "ServerView Operations Manager - Server Management"...

  • Page 74: Enabling Bitlocker Functionality

    Basic software procedures kudzu may not launch at boot depending on the client’s environment. Ê Select Keep Configuration and Ignore to complete the boot process. Ê Use the vi text editor to specify the MAC address in the HWADDR section of the ifcfg-eth<x>...

  • Page 75: Performing A Raid Array Rebuild

    Ê Follow the instructions in the BitLocker Setup wizard. For further information on how to enable BitLocker drive encryption, please refer to the Microsoft Knowledge Base. Fujitsu service partners will find additional information (also available in Japanese) on the Fujitsu Extranet web pages. 5.2.9...

  • Page 76: Looking Up Changed Mac / Wwn Addresses

    Basic software procedures CAUTION! The system is now operational, however, data redundancy will not be available until the RAID array rebuild is complete. Depending on the hard disk drive capacity the overall process can take up to several hours, in some cases even days.

  • Page 77: Configuring Lan Teaming

    After replacing the system board, system information has to be entered using the ChassisID_Prom Tool. The tool and further instructions are available to maintenance personnel from Fujitsu Technology Solutions Extranet: https://partners.ts.fujitsu.com/com/service/intelservers/tools For the Japanese market, follow the instructions provided separately.

  • Page 78: After Replacing The System Board

    Basic software procedures 5.2.12.2 After replacing the system board Ê Confirm with the customer whether the onboard LAN controller you have replaced has been used as part of a LAN teaming configuration. Ê If LAN teaming has been active, you will need to restore the configuration using the LAN driver utility after replacing the system board.

  • Page 79: Power Supply

    Power supply Safety notes CAUTION! Do not disassemble the power supply unit. Doing so may cause ● electric shock. Areas around the power supply unit may remain extremely hot after ● shutdown. After shutting down the server, wait for hot components to cool down before removing the power supply unit.

  • Page 80: Replacing The Power Supply Unit

    Power supply Replacing the power supply unit Field Replaceable Unit Hardware: 10 minutes (FRU) Tools: Phillips PH2 / (+) No. 2 screw driver 6.1.1 Preliminary steps "Disabling BitLocker functionality" on page 63 Ê "Shutting down the server" on page 40 Ê...
  • Page 81 Power supply Figure 26: Detaching the PSU Ê Remove the four screws from the PSU (see circles). Figure 27: Removing the PSU Ê Remove the fifth screw from the PSU (see circle). Ê Slide the defective PSU inside the chassis by 3 cm (1). Ê...

  • Page 82: Installing The New Power Supply Unit

    Power supply 6.1.3 Installing the new power supply unit Figure 28: Hooks for fastening the PSU Take care, that the PSU is fastening into the hooks (see circles). Figure 29: Installing the PSU Ê Insert the new PSU into the chassis (1). Ê...
  • Page 83 Power supply Figure 30: Securing the PSU Ê Secure the PSU to the chassis with four screws (see circles). Figure 31: Connecting power cable Ê Connect the PSU ATX power connector to system board connector "POWER". Upgrade and Maintenance Manual TX1310 M1...

  • Page 84: Concluding Steps

    Power supply 6.1.4 Concluding steps "Installing the side cover" on page 53 Ê "Connecting the server to the mains" on page 54 Ê "Switching on the server" on page 55 Ê "Enabling BitLocker functionality" on page 74 Ê Upgrade and Maintenance Manual TX1310 M1...

  • Page 85: Hard Disk Drives

    Hard disk drives Safety notes CAUTION! The hard disk drives must all be marked clearly so that they can be ● put back in their original places after an upgrade. If this is not done, existing data can be lost. Do not touch the circuitry on boards or soldered parts.

  • Page 86: Basic Information

    Hard disk drives Basic information 7.1.1 General equipping rules – Hard disk drives with different capacities are installed from highest to lowest capacity. – Hard disk drives with different rotation speeds are installed from highest to lowest speed. – Maximum configuration: 4x 3.5-inch HDDs 7.1.2 Mounting order Figure 32: 3.5-inch HDD mounting order...

  • Page 87: Installing 3.5-Inch Hdds

    Hard disk drives Installing 3.5-inch HDDs Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less 7.2.1 Preliminary steps "Shutting down the server" on page 40 Ê "Disconnecting the server from the mains" on page 41 Ê "Removing the side cover" on page 42 Ê...

  • Page 88: Installing A 3.5-Inch Hdd

    Hard disk drives 7.2.3 Installing a 3.5-inch HDD Figure 34: Aligning the Easyclick rails Ê Align the three pins on the Easyclick rails with the screw holes on the hard disk drive. Figure 35: Attaching the Easyclick rails Ê Attach an Easyclick rail on each side of the hard disk drive. Upgrade and Maintenance Manual TX1310 M1...
  • Page 89 Hard disk drives Figure 36: Inserting the 3.5-inch HDD Ê Insert the hard disk drive into its installation bay. Ê Slide the hard disk drive into its installation bay until the Easyclick rails click in place. Figure 37: Connecting the power cable (example P4 to HDD1) Ê...
  • Page 90 Hard disk drives Ê Connect the SATA cable to the hard disk drive and to the corresponding controller as described in the following examples. Example SATA cabling to SATA onboard controller Figure 38: Connecting SATA cables to the system board Ê...

  • Page 91: Concluding Steps

    Hard disk drives Figure 40: Connecting SATA cables to HDD3 and HDD4 Ê Connect the corresponding SATA cable to the hard disk drive: SATA cable connected to SATA3 to HDD3 SATA cable connected to SATA4 to HDD4 For further cabling information, please refer to section "Cables"...

  • Page 92: Removing 3.5-Inch Hdds

    Hard disk drives Removing 3.5-inch HDDs Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less 7.3.1 Preliminary steps Ê Ensure that the hard disk drive to be removed is not combined into a RAID array. If the drive is part of a RAID array, you first need to delete the array using ServerView RAID Manager or BIOS Setup Utility.

  • Page 93: Removing A 3.5-Inch Hdd

    Hard disk drives 7.3.2 Removing a 3.5-inch HDD Figure 41: Disconnecting the cables Ê Disconnect the power cable (1) and the SATA cable (2) from the desired hard disk drive. Upgrade and Maintenance Manual TX1310 M1...
  • Page 94 Hard disk drives Figure 42: Disconnecting SATA cables from the system board Ê Disconnect the corresponding SATA cable(s) from the system board. Push the edge (see arrow) of the system board with the finger to avoid bending up the system board. SATA cable to connector SATA1 SATA cable to connector SATA2 SATA cable to connector SATA3...
  • Page 95 Hard disk drives Figure 43: Removing a 3.5-inch HDD Ê Press the green handles of the Easyclick rails inwards (1) to release the locking mechanism and pull the hard disk drive completely out of its bay (2). Figure 44: Detaching the Easyclick rails Ê...

  • Page 96: Inserting The Easyclick Rails In The Bay

    Hard disk drives 7.3.3 Inserting the Easyclick rails in the bay Figure 45: Inserting the Easyclick rails in the bay Ê Push the Easyclick rails completely into the bay (1). Ê Press the green handle outwards until it locks in place (2) 7.3.4 Concluding steps "Installing the side cover"...

  • Page 97: Replacing A 3.5-Inch Hdd

    Hard disk drives Replacing a 3.5-inch HDD Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less CAUTION! All hard disk drives must be uniquely identified so that they can be reinstalled in their original mounting locations later. If this is not done, existing data can be lost.

  • Page 98: Installing The New 3.5-Inch Hdd

    Hard disk drives 7.4.3 Installing the new 3.5-inch HDD Ê Install the hard disk drive as described in section "Installing a 3.5-inch HDD" on page 7.4.4 Concluding steps "Installing the side cover" on page 53 Ê "Connecting the server to the mains" on page 54 Ê...

  • Page 99: System Fans

    System fans Safety notes CAUTION! Do not damage or modify internal cables or devices. Doing so may ● cause a device failure, fire, or electric shock. Devices and components inside the server remain hot after ● shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options.

  • Page 100: Basic Information

    System fans Basic information CAUTION! Since the system fans are not redundant they have to be replaced immediately in case of defects or pre-failure events. Figure 46: Positions of the system fans Upgrade and Maintenance Manual TX1310 M1...
  • Page 101 System fans In the latest chassis version the system fan 2 comes without a fan guard. A corresponding warning label is added. (1). The pictures doesn’t always show the current version. Figure 47: Fan without guard Additional fans in power supply units cannot be replaced individually. Upgrade and Maintenance Manual TX1310 M1...

  • Page 102: Replacing The System Fan 2

    System fans Replacing the system fan 2 Upgrade and Repair Unit Hardware: 15 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver 8.2.1 Preliminary steps "Shutting down the server" on page 40 Ê "Disconnecting the server from the mains" on page 41 Ê...
  • Page 103 System fans Figure 49: Disconnecting the fan cable Ê Disconnect the fan cable from system board connector "FAN2 SYS". Figure 50: Cable clamp of the fan cable Ê Open the cable clamp and remove the fan cable. Upgrade and Maintenance Manual TX1310 M1...
  • Page 104 System fans Figure 51: Removing the system fan 2 Ê Push the system fan 2 in the direction of arrow. Ê Lift the system fan 2 out of the chassis. Upgrade and Maintenance Manual TX1310 M1...

  • Page 105: Installing The New System Fan 2

    System fans 8.2.3 Installing the new system fan 2 Figure 52: Installing the system fan 2 Check the position of the four fan bushings. Adjust the bushings in the chassis, if necessary. Ê Slide the system fan 2 to the right as far as it will go. Upgrade and Maintenance Manual TX1310 M1...
  • Page 106 System fans Figure 53: Fastening the screws of the system fan 2 figure 53 shows the correct position of the four fan bushings. Ê Fasten the four screws (see circles). Upgrade and Maintenance Manual TX1310 M1...
  • Page 107 System fans Figure 54: Connecting the fan cable Ê Connect the fan cable to system board connector "FAN2 SYS". Figure 55: Cable clamp of the fan cable Ê Open the cable clamp and insert the fan cable. Upgrade and Maintenance Manual TX1310 M1...

  • Page 108: Concluding Steps

    System fans 8.2.4 Concluding steps "Installing the HDD cage" on page 59 Ê "Reassembling" on page 47 Ê "Connecting the server to the mains" on page 54 Ê "Switching on the server" on page 55 Ê Upgrade and Maintenance Manual TX1310 M1...

  • Page 109: Replacing The System Fan 1

    System fans Replacing the system fan 1 Upgrade and Repair Unit Hardware: 15 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver 8.3.1 Preliminary steps "Shutting down the server" on page 40 Ê "Disconnecting the server from the mains" on page 41 Ê...
  • Page 110 System fans Figure 57: Pushing the HDD cage from the system fan 1 Ê Push the HDD cage in the direction of the arrow to loosen the system fan 1. Figure 58: Position of the bushings The bushings remain at the HDD cage. It is not necessary to remove them. Upgrade and Maintenance Manual TX1310 M1...
  • Page 111 System fans Figure 59: Removing the bushings Ê Remove the two screws from the fan (1, see circles). Ê Remove the two bushings from the fan (2). Keep the screws and bushings for further use. You will need both to prepare the replacement of the fan.

  • Page 112: Installing The New System Fan 1

    System fans 8.3.3 Installing the new system fan 1 Figure 60: Installing the bushings Ê Place the two bushings on the fan (1, see circles). Ê Secure each bushing on the fan with one fan screw (2). Upgrade and Maintenance Manual TX1310 M1...
  • Page 113 System fans Figure 61: Pushing the HDD cage over the system fan 1 Ê Check the correct position of the bushings. Ê Slide the HDD cage in the direction of the arrow as far as it will go. Take care that the bushings are not shifted while the HDD cage is slid. Upgrade and Maintenance Manual TX1310 M1...

  • Page 114: Concluding Steps

    System fans Figure 62: Installing the system fan 1 Ê Fasten the system fan 1 to the HDD cage with two screws (see circles). 8.3.4 Concluding steps "Installing the HDD cage" on page 59 Ê "Reassembling" on page 47 Ê "Connecting the server to the mains"...

  • Page 115: Expansion Cards And Backup Units

    Expansion cards and backup units Safety notes CAUTION! Do not damage or modify internal cables or devices. Doing so may ● cause a device failure, fire, or electric shock. Devices and components inside the server remain hot after ● shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options.

  • Page 116: Basic Information

    Expansion cards and backup units Basic information Configuration options may vary depending on base unit (see "Different versions for TX1310 M1" on page 16). The system board is equipped with four expansion card slots: Figure 63: PCI slot overview PCI slot Type Function PCIe x1...

  • Page 117: Equipping The Pcie Slots

    Gigabit CT Desktop PCIe Adapter (LAN) For the latest information of the installing order, refer to your server’s hardware configurator available online at the following address: for the EMEA market: http://ts.fujitsu.com/products/standard_servers/index.html for the Japanese market: http://jp.fujitsu.com/platform/server/primergy/system/ Upgrade and Maintenance Manual TX1310 M1...

  • Page 118: Handling Slot Brackets

    Expansion cards and backup units Handling slot brackets 9.2.1 Installing a slot bracket Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver Figure 64: Non-perforated slot bracket Full height bracket non-perforated Installing the slot bracket Ê...
  • Page 119 Expansion cards and backup units ® Example network adapter Ethernet Server Adapter Intel i350-T2 ® Figure 65: Placing the slot bracket - Intel i350-T2 Ê Carefully shift the slot bracket towards the controller until the plug shells engage with the cut-outs in the slot bracket connector panel. Ê...
  • Page 120 Expansion cards and backup units ® Example network adapter Ethernet Adapter Intel Gbit CT2 ® Figure 67: Placing the slot bracket - Intel Gbit CT2 Ê Carefully shift the slot bracket towards the controller until the plug shells engage with the cut-outs in the slot bracket connector panel. Ê...
  • Page 121 Expansion cards and backup units Example network adapter NVIDIA NVS 300 Figure 69: Placing the slot bracket (A) - NVIDIA NVS 300 Ê Carefully shift the slot bracket towards the controller until the plug shells engage with the cut-outs in the slot bracket connector panel. Ê...

  • Page 122: Removing A Slot Bracket

    Expansion cards and backup units Figure 71: Securing the slot bracket - NVIDIA NVS 300 Ê Secure the screw of the slot bracket to the chassis. 9.2.2 Removing a slot bracket Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver Removing the slot bracket Ê...

  • Page 123: Expansion Cards

    Expansion cards and backup units Expansion cards 9.3.1 Installing expansion cards Upgrade and Repair Unit Hardware: 5 minutes (URU) Software: 5 minutes Tools: Phillips PH2 / (+) No. 2 screw driver (only for installing slot brackets) 9.3.1.1 Preliminary steps "Disabling BitLocker functionality" on page 63 Ê...
  • Page 124 Expansion cards and backup units Ê Open the slot bracket clamp and remove it. Figure 73: Removing the PCI slot bracket (B) Ê Remove the slot bracket. CAUTION! Keep the slot bracket for further use. Always replace slot brackets into unused PCI slot openings to comply with applicable EMC regulations and satisfy cooling requirements.

  • Page 125: Installing An Expansion Card

    Expansion cards and backup units 9.3.1.3 Installing an expansion card Ê Remove the expansion card from its protective packaging. For further instructions regarding controller settings, please refer to the accompanying documentation. Ê If applicable, attach the required slot bracket to the expansion card as described in section "Installing a slot bracket"...

  • Page 126: Concluding Steps

    Expansion cards and backup units 9.3.1.4 Concluding steps "Installing the side cover" on page 53 Ê Ê If applicable, connect external cables to the expansion card. "Connecting the server to the mains" on page 54 Ê "Switching on the server" on page 55 Ê...

  • Page 127: Removing Expansion Cards

    Expansion cards and backup units 9.3.2 Removing expansion cards Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 9.3.2.1 Preliminary steps "Disabling BitLocker functionality" on page 63 Ê "Shutting down the server" on page 40 Ê Ê If applicable, disconnect all external cables from the expansion card to be removed.

  • Page 128: Installing A Pci Slot Bracket

    Expansion cards and backup units Figure 77: Removing an expansion card (B) Ê Carefully remove the expansion card from its slot. 9.3.2.3 Installing a PCI slot bracket CAUTION! Always replace slot brackets into unused PCI slot openings to comply with applicable EMC regulations and satisfy cooling requirements. Figure 78: Installing a PCI slot bracket (A) Ê...

  • Page 129: Concluding Steps

    Expansion cards and backup units Figure 79: Installing the expansion card (B) Ê Close the slot bracket clamp. 9.3.2.4 Concluding steps "Installing the side cover" on page 53 Ê "Connecting the server to the mains" on page 54 Ê "Switching on the server" on page 55 Ê...

  • Page 130: Replacing Expansion Cards

    Expansion cards and backup units 9.3.3 Replacing expansion cards Upgrade and Repair Unit Hardware: 5 minutes (URU) Software: 5 minutes Tools: Phillips PH2 / (+) No. 2 screw driver (only for installing slot brackets) Note on network settings recovery When replacing network controllers or the system board, network configuration settings in the operating system will be lost and replaced by default values.

  • Page 131: Concluding Steps

    Expansion cards and backup units 9.3.3.4 Concluding steps "Installing the side cover" on page 53 Ê "Connecting the server to the mains" on page 54 Ê "Switching on the server" on page 55 Ê "Enabling replaced components in the system BIOS" on page 70 Ê...
  • Page 132 Expansion cards and backup units Upgrade and Maintenance Manual TX1310 M1...

  • Page 133: Main Memory

    Main memory Safety notes CAUTION! Do not install unsupported third party memory modules. For further ● information on supported memory modules, refer to section "Basic information" on page 134. Doing so may cause electric shock, a fire, or failures. Memory modules remain hot after shutdown. Wait for components to ●...

  • Page 134: Basic Information

    Main memory 10.1 Basic information Configuration options may vary depending on base unit (see "Different versions for TX1310 M1" on page 16). – The system board is equipped with four memory slots. – The system has to be equipped with at least one memory module. Populate memory slot 1 / channel A (DIMM-1A) first.

  • Page 135: Operation Modes

    Main memory 10.1.2 Operation modes – The maximum performance can be achieved in a symmetric dual-channel configuration. Therefore both channels have to be populated with the same amount of memory. The DRAM device technology (1 Gbit / 2 Gbit / 4 Gbit) may vary from one channel to the other.

  • Page 136: Installing Memory Modules

    Main memory 10.2 Installing memory modules Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 10.2.1 Preliminary steps "Disabling BitLocker functionality" on page 63 Ê "Shutting down the server" on page 40 Ê "Disconnecting the server from the mains" on page 41 Ê...

  • Page 137: Concluding Steps

    Main memory Figure 82: Installing memory modules (B) Ê Align the notch on the bottom of the module with the crossbar in the connector (see circle). Figure 83: Installing memory modules (C) Ê Press down on the memory module until the securing clips snap into the cutouts at each end of the module.

  • Page 138: Removing Memory Modules

    Main memory 10.3 Removing memory modules Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 10.3.1 Preliminary steps "Disabling BitLocker functionality" on page 63 Ê "Shutting down the server" on page 40 Ê "Disconnecting the server from the mains" on page 41 Ê...

  • Page 139: Concluding Steps

    Main memory 10.3.3 Concluding steps "Installing the side cover" on page 53 Ê "Connecting the server to the mains" on page 54 Ê Ê If applicable, "Updating or recovering the system board BIOS" on page 68 "Switching on the server" on page 55 Ê...

  • Page 140: Concluding Steps

    Main memory 10.4.4 Concluding steps "Installing the side cover" on page 53 Ê "Connecting the server to the mains" on page 54 Ê Ê If applicable, "Updating or recovering the system board BIOS" on page 68 "Enabling replaced components in the system BIOS" on page 70 Ê...

  • Page 141: Processor

    Processor Safety notes CAUTION! Do not install unsupported processors. For further information on ● supported processors, refer to section "Basic information" on page 142. Circuit boards and soldered parts of internal options are exposed and ● can be damaged by static electricity. Always discharge static build-up (e.g.

  • Page 142: Basic Information

    Processor 11.1 Basic information – The system board supports one processor socket. 11.2 Replacing the processor Field Replaceable Unit Hardware: 15 minutes (FRU) Software: 5 minutes Tools: Phillips PH2 / (+) No. 2 screw driver CAUTION! Processors are extremely sensitive to electrostatic discharge and must be handled with care.

  • Page 143: Removing The Heat Sink

    Processor 11.2.2 Removing the heat sink Removing the heat sink Figure 85: Removing the heat sink (A) Ê Loosen the four captive screws on the heat sink in a crossover pattern (1-4). Upgrade and Maintenance Manual TX1310 M1...
  • Page 144 Processor Figure 86: Removing the heat sink (B) Ê Disconnect the heat sink fan connector from the system board connector FAN CPU (1). Ê Carefully turn the heat sink back and forth to detach it from the processor (2). This may be necessary due to the adhesive quality of the thermal paste located between the heat sink and processor.

  • Page 145: Removing Processor

    Processor 11.2.3 Removing processor Field Replaceable Unit Hardware: 15 minutes (FRU) Software: 5 minutes Tools: Tool-less CAUTION! Processors are extremely sensitive to electrostatic discharge and must be handled with care. After a processor has been removed from its protective sleeve or from its socket, place it upside down on a nonconducting, antistatic surface.
  • Page 146 Processor Figure 87: Opening socket release lever Ê Unlatch the socket release lever by pushing it down and away from the socket (1), and then swivel it up (2). Figure 88: Opening the load plate Ê Open the load plate of the processor socket. CAUTION! Handle the locking frame carefully.
  • Page 147 Processor Figure 89: Removing the processor Ê Carefully remove the defective processor from its socket in a vertical motion. CAUTION! Be careful not to touch or bend the spring contacts on the processor socket. Ê Thoroughly clean residual thermal paste from the processor surface using a lint-free cloth.

  • Page 148: Installing The Protective Cover

    Processor 11.2.3.3 Installing the protective cover Figure 90: Attaching the protective socket cover Ê Carefully lower the protective socket cover onto the processor socket in a vertical motion until it snaps in place. Figure 91: Closing the load plate Ê Close the load plate of the processor. Upgrade and Maintenance Manual TX1310 M1...

  • Page 149: Concluding Steps

    Processor Figure 92: Close the socket release lever Ê Close the socket release lever (1) and latch it under the load plate retention tab to lock down the load plate (2). 11.2.4 Concluding steps "Reassembling" on page 47 Ê "Connecting the server to the mains" on page 54 Ê...

  • Page 150: Installing A Processor

    Processor 11.2.5 Installing a processor This description applies to the following procedures: – Transferring a processor after replacing the system board (see section "Replacing the system board" on page 206) 11.2.5.1 Removing the protective cover Figure 93: Opening socket release lever Ê...
  • Page 151 Processor Ê Open the load plate of the processor socket. CAUTION! Handle the locking frame carefully. In a vertical position, the small clip (see circle) can scratch the system board. Figure 95: Removing the protective cover Ê Remove the black protective cover from the processor socket. Upgrade and Maintenance Manual TX1310 M1...

  • Page 152: Installing The New Processor

    Processor 11.2.5.2 Installing the new processor Figure 96: Installing the processor Ê Hold the processor with your thumb and index finger. Ê Place the new processor on the socket. Make sure that the recesses on the processor are aligned with the corresponding markings on the socket.
  • Page 153 Processor Figure 97: Closing the load plate Ê Close the load plate of the processor. Figure 98: Closing the socket release lever Ê Close the socket release lever (1) and latch it under the load plate retention tab (2) to lock down the load plate. Upgrade and Maintenance Manual TX1310 M1...

  • Page 154: Applying Thermal Paste

    Processor 11.2.6 Applying thermal paste For the Japanese market, the service engineer must follow the instruction provided separately. If the processor upgrade or replacement kit contains a new CPU heat sink, a thin layer of thermal compound has already been pre-applied to its lower surface.
  • Page 155 Processor Figure 100: Applying thermal paste Ê Apply a small point-shaped amount of thermal paste (1.0 gram, see description above) to the center of the processor surface as shown. CAUTION! Do not mix different types of thermal paste. Upgrade and Maintenance Manual TX1310 M1...

  • Page 156: Installing The Heat Sink

    Processor 11.2.7 Installing the heat sink Installing the heat sink Figure 101: Installing the heat sink (A) Ê Carefully seat the heat sink on the four threaded holes as shown. CAUTION! – Ensure that the screws on the heat sink are properly seated on the threaded holes (see circles).

  • Page 157: Concluding Steps

    Processor Figure 102: Installing the heat sink (B) Ê Fasten the four captive screws on the heat sink in a crossover pattern (screw torque: 0.6 Nm, not applicable for the Japanese market) (1-4). Ê Connect the heat sink fan connector to system board connector FAN CPU (5).

  • Page 158: Replacing The Heat Sink

    Processor 11.3 Replacing the heat sink Field Replaceable Unit Hardware: 15 minutes (FRU) Tools: Phillips PH2 / (+) No. 2 screw driver 11.3.1 Preliminary steps "Shutting down the server" on page 40 Ê "Disconnecting the server from the mains" on page 41 Ê...

  • Page 159: Accessible Drives

    Accessible drives Safety notes CAUTION! Before installing an internal accessible drive, see the manual for the ● accessible drive. Before installing/removing an accessible drive to/from the server, turn ● off the server, all peripheral devices, and any other connected devices. Also unplug all power cables from the outlet. Failure to do so can cause electric shock.

  • Page 160: Basic Information

    Accessible drives 12.1 Basic information Mounting order for accessible drives The server offers two 5.25-inch accessible drive bays for optical disk drives and backup drives. Figure 103: Accessible drive bays Sequence Accessible drive Max. # Optical disk drive Bay 1 or slimline optical disk drive RDX backup drive Bay 2...

  • Page 161: Installing Accessible Drives

    Accessible drives 12.2 Installing accessible drives Upgrade and Repair Unit Hardware: 10 minutes (URU) Tools: Phillips PH0 / (+) No. 0 screw driver diagonal pliers 12.2.1 Preliminary steps "Disabling BitLocker functionality" on page 63 Ê "Shutting down the server" on page 40 Ê...

  • Page 162: Removing The Dummy Cover Of Bay 2

    Accessible drives 12.2.2 Removing the dummy cover of bay 2 If bay 2 will be equipped, it is necessary to break out the dummy cover of bay 2 in the front cover and to remove the EMI spring in bay 2. Some chassis do not have any more the EMI spring installed in bay 2.
  • Page 163 Accessible drives Figure 105: Connected points of the EMI spring of bay 2 Figure 106: Connected points of the EMI spring of bay 2 Ê Cut the three connected points of the EMI spring with a diagonal pliers. Ê Remove the EMI spring. Ê...

  • Page 164: Installing An Optical Disk Drive (Odd)

    Accessible drives 12.2.3 Installing an optical disk drive (ODD) 12.2.3.1 Preparing the optical disk drive There are two fixation plates for accessible drives. You need one fixation plate for an accessible drive to be installed. Figure 107: Removing the fixation plate from the chassis Ê...
  • Page 165 Accessible drives Figure 108: Attaching the fixation plate to the optical disk drive (A) Ê Align the four pins of the fixation plate with the screw holes on the optical disk drive. Figure 109: Attaching the fixation plate to the optical disk drive (B) Ê...

  • Page 166: Installing The Optical Disk Drive

    Accessible drives 12.2.3.2 Installing the optical disk drive Ê Install the optical disk drive as described in section "Installing the optical disk drive (ODD)" on page Figure 110: Routing optical disk drive cables Ê Connect the SATA cable to connector "SATA 5" on the system board. Ê...

  • Page 167: Installing A Slimline Optical Disk Drive (Odd)

    Accessible drives 12.2.4 Installing a slimline optical disk drive (ODD) 12.2.4.1 Mounting the slimline drive in the slide-in unit Figure 111: Slide-in unit for slimline ODD drive Figure 112: Mounting the slimline ODD in the slide-in unit (A) Ê Insert the slimline ODD on the top. Ê...

  • Page 168: Preparing The Slide-In Unit

    Accessible drives Figure 113: Mounting the slimline ODD in the slide-in unit (B) Ê Fasten it with two M2 x 2.5 mm screws to the slide-in unit on the left side. 12.2.4.2 Preparing the slide-in unit There are two fixation plates for accessible drives. You need one fixation plate for an accessible drive to be installed.

  • Page 169: Installing The Slide-In Unit

    Accessible drives 12.2.4.3 Installing the slide-in unit Figure 115: Installing the slide-in unit Ê Insert the slide-in unit into its installation bay and carefully push in until it locks in place. Figure 116: Connecting cables to the slimline optical disk drive Ê...

  • Page 170: Installing A Backup Drive

    Accessible drives Figure 117: Routing slimline drive cables Ê Connect the SATA cable to connector "SATA 5" on the system board. Ê Route the SATA cable below system fan 1. 12.2.5 Installing a backup drive Notes on RDX drive USB cabling: –...

  • Page 171: Preparing The Backup Drive

    Accessible drives 12.2.5.1 Preparing the backup drive There are two fixation plates for accessible drives. You need one fixation plate for an accessible drive to be installed. Ê Remove the fixation plate from the chassis (see figure 107). Figure 118: Attaching the fixation plate to the backup drive (A) Ê...

  • Page 172: Installing The Backup Drive

    Accessible drives 12.2.5.2 Installing the backup drive Ê Install the backup drive as described in section "Installing the backup drive" on page Figure 120: Connecting USB 3.0 cable to system board Ê Connect the USB 3.0 cable to onboard USB3.0 connector "USB 1" on the system board.

  • Page 173: Removing Accessible Drives

    Accessible drives 12.3 Removing accessible drives Upgrade and Repair Unit Hardware: 10 minutes (URU) Tools: tool-less 12.3.1 Preliminary steps "Disabling BitLocker functionality" on page 63 Ê "Removing backup and optical disk media" on page 64 Ê "Verifying and configuring the backup software solution" on page 65 Ê...

  • Page 174: Removing A Slimline Optical Disk Drive (Odd)

    Accessible drives 12.3.3 Removing a slimline optical disk drive (ODD) Figure 121: Disconnecting cables to the slimline drive Ê Disconnect all cables from the slimline optical disk drive. Power adapter cable from the power cable connector P8 and the slimline drive. SATA cable Upgrade and Maintenance Manual TX1310 M1...

  • Page 175: Removing A Backup Drive

    Accessible drives Figure 122: Removing the slide-in unit Ê Press the locking latch in the direction of the arrow (1) and press out the slide-in unit from behind (2). Ê Pull the slide-in unit out of its bay. 12.3.4 Removing a backup drive Ê...

  • Page 176: Installing The Dummy Drive

    Accessible drives 12.3.5 Installing the dummy drive CAUTION! Always replace the dummy drive into the unused drive bays to comply with applicable EMC regulations and satisfy cooling requirements. Figure 123: Dummy drive for bay 2 Figure 124: Attaching the fixation plate to the dummy drive for bay 2 Upgrade and Maintenance Manual TX1310 M1...

  • Page 177: Concluding Steps

    Accessible drives Figure 125: Installing the dummy drive in bay 2 Ê Insert the dummy drive in bay 2 and carefully push it in until it locks in place. The dummy drive is a little harder to insert than an ODD and the bezel of the drive is touching the front panel.

  • Page 178: Replacing Accessible Drives

    Accessible drives 12.4 Replacing accessible drives Upgrade and Repair Unit Hardware: 15 minutes (URU) Tools: Phillips PH0 / (+) No. 0 screw driver 12.4.1 Preliminary steps "Disabling BitLocker functionality" on page 63 Ê "Removing backup and optical disk media" on page 64 Ê...

  • Page 179: Replacing A Slimline Optical Disk Drive (Odd)

    Accessible drives Figure 127: Attaching the fixation plate to the optical disk drive Ê Attach the fixation plate on the left side of the new optical disk drive. Ê Install the new optical disk drive as described in section "Installing an optical disk drive (ODD)"...
  • Page 180 Accessible drives Figure 128: Removing the fixation plate from the slide-in unit Ê Remove the fixation plate from the left side of the slide-in unit. Figure 129: Removing the slimline ODD from the slide-in unit (A) Ê Remove the three M2 x 2.5 mm screws from the left side of the slide-in unit. Upgrade and Maintenance Manual TX1310 M1...

  • Page 181: Replacing A Backup Drive

    Accessible drives Figure 130: Removing the slimline ODD from the slide-in unit (B) Ê Remove the M2 x 2.5 mm screw from the right side of the slide-in unit. Ê Remove the slimline ODD drive from the slide-in unit. Ê Install the new slimline ODD as described in section "Installing a slimline optical disk drive (ODD)"...

  • Page 182: Concluding Steps

    Accessible drives Figure 132: Attaching the fixation plate to the backup drive Ê Attach the fixation plate on the left side of the new backup drive. Ê Install the new backup drive as described in section "Installing a backup drive" on page 170.

  • Page 183: Front Panel And Front Usb

    Front panel and front USB Safety notes CAUTION! For further safety information, please refer to chapter "Important ● information" on page 13.1 Replacing the front panel cable Field Replaceable Unit Hardware: 15 minutes (FRU) Tools: Phillips PH2 / (+) No. 2 screw driver The On/Off button and the HDD activity LED are part of the front panel cable.

  • Page 184: Removing The On/Off Button And The Hdd Activity Led

    Front panel and front USB 13.1.2 Removing the On/Off button and the HDD activity Figure 133: Removing the On/Off button Ê Press the two retaining clips together and push the On/Off button backwards in the chassis. Note the orientation of the On/Off button. If it is installed in the other direction, it does not work properly.

  • Page 185: Removing The Front Panel Cable

    Front panel and front USB 13.1.3 Removing the front panel cable Figure 135: Disconnecting front panel cable Ê Open the cable clamp and remove the front panel cable (1). Ê Disconnect the front panel cable from system board connector "Front panel"...

  • Page 186: Installing The On/Off Button And The Hdd Activity Led

    Front panel and front USB 13.1.5 Installing the On/Off button and the HDD activity Figure 137: Installing the On/Off button Ê Insert the On/Off button in the direction shown until it snaps in place (1). Take care of the orientation of the On/Off button. If it is installed in the other direction, it does not work properly.

  • Page 187: Replacing The Front Usb Module

    Front panel and front USB 13.2 Replacing the front USB module Field Replaceable Unit Hardware: 15 minutes (FRU) Tools: Phillips PH2 / (+) No. 2 screw driver 13.2.1 Preliminary steps "Disabling BitLocker functionality" on page 63 Ê "Shutting down the server" on page 40 Ê...

  • Page 188: Removing The Defective Front Usb Module

    Front panel and front USB 13.2.2 Removing the defective front USB module Ê Disconnect the front USB cable from the system board. Figure 138: Removing the front USB module Ê Remove the four screws of the front USB module Ê Remove the front USB module. Upgrade and Maintenance Manual TX1310 M1...
  • Page 189 Front panel and front USB Figure 139: Removing the front USB cable from the carrier (A) Ê Remove the two screws of the USB cable from the carrier. Figure 140: Removing the plate from the carrier (B) Ê Remove the two screws and pull the plate out of the carrier. Upgrade and Maintenance Manual TX1310 M1...

  • Page 190: Installing The New Front Usb Module

    Front panel and front USB 13.2.3 Installing the new front USB module Figure 141: Installing the gasket in the carrier Ê If applicable, insert the gasket in the carrier. Take care that the gasket fits with the recesses of the carrier. Figure 142: Installing the plate into the carrier (A) Ê...
  • Page 191 Front panel and front USB Figure 143: Installing the front USB cable into the carrier (B) Ê Secure the new front USB cable with two screws. Upgrade and Maintenance Manual TX1310 M1...

  • Page 192: Concluding Steps

    Front panel and front USB Figure 144: Installing the front USB module Ê Place the new front USB module in the direction shown and secure it with four screws (see circles). Ê Connect the front USB cable to the front USB connector on the system board.

  • Page 193: System Board And Components

    System board and components Safety notes CAUTION! Devices and components inside the server remain hot after ● shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options. Circuit boards and soldered parts of internal options are exposed and ●...

  • Page 194: Replacing The Cmos Battery

    System board and components 14.2 Replacing the CMOS battery Upgrade and Repair Unit Hardware: 15 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver; recommended: tooth pick Safety notes CAUTION! The CMOS battery must be replaced with an identical battery or with ●...

  • Page 195: Replacing The Defective Cmos Battery

    System board and components 14.2.2 Replacing the defective CMOS battery Figure 145: Replacing the CMOS battery Ê Press the locking spring into direction of the arrow (1), so that the CMOS battery jumps out of its socket. Ê Remove the CMOS battery (2). CAUTION! Sharp tools such as screw drivers might damage system board components in case of slipping.

  • Page 196: Trusted Platform Module (Tpm)

    System board and components "Connecting the server to the mains" on page 54 Ê "Switching on the server" on page 55 Ê "Verifying the system time settings" on page 72 Ê Ê If applicable, restore the BIOS settings manually. 14.3 Trusted Platform Module (TPM) 14.3.1 Installing the TPM Field Replaceable Unit...

  • Page 197: Installing The Tpm

    System board and components 14.3.1.2 Installing the TPM Figure 146: TPM installation kit TPM (Trusted Platform Module) Special screw for TPM TPM spacer TPM bit insert for TPM special screw The black TPM spacer is not used in this server. Figure 147: TPM mounting location Upgrade and Maintenance Manual TX1310 M1...
  • Page 198 System board and components Figure 148: Installing the TPM spacer Ê Snap the TPM spacer into the cut-out in the system board. Figure 149: TPM bit insert Ê Attach the TPM bit insert or TPM module fixing tool (Japanese market) to a bit screw driver.

  • Page 199: Concluding Steps

    System board and components Figure 150: Installing the TPM Ê Connect the TPM to the system board (1). Ê Fasten the TPM with the special screw for the TPM using the TPM bit insert or TPM module fixing tool (Japanese market) (2). CAUTION! Do not fasten the screw too firmly.

  • Page 200: Removing The Tpm

    System board and components For detailed information on how to access the BIOS and modify settings, refer to the corresponding BIOS Setup Utility reference manual. "Connecting the server to the mains" on page 54 Ê 14.3.2 Removing the TPM Field Replaceable Unit Hardware: 30 minutes (FRU) Tools: Removing the system board:...
  • Page 201 For further information on how to disable BitLocker drive encryption, please refer to the Microsoft Knowledge Base. Fujitsu service partners will find additional information (also available in Japanese) on the Fujitsu Extranet web pages. Ê Disable TPM in the system board BIOS. Proceed as follows: Ê...

  • Page 202: Removing The Tpm

    System board and components 14.3.2.2 Removing the TPM Ê Remove the system board as described in section "Removing the defective system board" on page 208. Ê Lay the system board on a soft, antistatic surface with its component side facing down. Figure 151: Removing the TPM Ê...

  • Page 203: Concluding Steps

    System board and components Figure 152: Removing the TPM spacer Ê Using a flat nose pliers, press together the hooks on the TPM spacer and remove it from the system board. If the TPM is to be replaced, the TPM spacer may remain on the system board.

  • Page 204: Replacing The Tpm

    System board and components 14.3.3 Replacing the TPM Field Replaceable Unit Hardware: 40 minutes (FRU) Tools: Removing the system board: – Phillips PH2 / (+) No. 2 screw driver Replacing the TPM: – Bit screw driver – TPM bit insert –...

  • Page 205: Removing The Defective Tpm

    System board and components 14.3.3.2 Removing the defective TPM Ê Remove the TPM as described in section "Removing the TPM" on page 200. Ê Leave the TPM spacer on the system board when removing the defective TPM. 14.3.3.3 Installing the new TPM The TPM spacer is already present on the system board.

  • Page 206: Replacing The System Board

    System board and components 14.4 Replacing the system board Field Replaceable Unit Hardware: 50 minutes (FRU) Software: 10 minutes Tools: Replacing the system board: – Phillips PH2 / (+) No. 2 screw driver – Magnifying glass for inspecting processor socket springs (recommended) Replacing the TPM: –...

  • Page 207: Preliminary Steps

    System board and components CAUTION! – Before replacing the system board, ask the customer whether TPM functionality is used. – If the customer is using TPM functionality, remove the TPM from the old system board and install it on the new system board. Advise your contact persons that they must provide you with TPM backup copies.

  • Page 208: Removing The Defective System Board

    System board and components Ê Remove all memory modules, see section "Removing memory modules" on page 138. Before removing the memory modules, take a note on the installation slot number for each memory module. Make sure that you reinstall the memory modules in the slot they were located before the replacement.
  • Page 209 System board and components Figure 153: Detaching the system board (A) Ê Remove six screws from the system board (see circles). Upgrade and Maintenance Manual TX1310 M1...
  • Page 210 System board and components Figure 154: Detaching the system board (B) Ê Slightly lift up the system board by the memory module ejectors and a PCI slot (1) in order to detach it from the centering bolts (2). Ê Carefully shift the system board towards the server front until the plug shells disengage from the cut-outs in the connector panel (3).
  • Page 211 System board and components Figure 155: Removing the system board Ê Hold the system board by the memory module ejectors and a PCI slot and at a slight angle lift it out of the chassis. Ê If applicable, remove the TPM as described in section "Removing the TPM"...

  • Page 212: Installing The New System Board

    System board and components 14.4.3 Installing the new system board 14.4.3.1 Mounting the system board Figure 156: Installing the system board (A) Ê Hold the new system board by the memory module ejectors and a PCI slot. CAUTION! – Do not lift or handle the system board by any of its heat sinks! –...
  • Page 213 System board and components Figure 157: Installing the system board (B) Ê Carefully shift the system board towards the server rear until the plug shells engage with the cut-outs in the connector panel (1). Ê Lower the system board onto the centering bolts (2). Ensure that the system board is properly seated on both centering bolts.
  • Page 214 System board and components Figure 158: Securing the system board Ê Secure the system board with six screws (see circles). Screw torque: 0.6 Nm (not applicable for the Japanese market) Tighten the screws in a cross diagonal pattern. Upgrade and Maintenance Manual TX1310 M1...

  • Page 215: Swapping The Processor

    System board and components 14.4.3.2 Swapping the processor CAUTION! Be careful not to touch or bend the pins on the processor socket! Save the socket cover for future use. Always replace the socket cover if you remove the processor from the socket. Ê...
  • Page 216 System board and components Ê Restore the BIOS settings manually. Ê If applicable, activate TPM functionality in the system BIOS under Security > TPM (Security Chip) Setting > Security Chip. For more information, refer to the corresponding BIOS Setup Utility reference manual. "Verifying the system time settings"...

  • Page 217: Cables

    Cables 15.1 Overview cables No. Part number Description From - to from On/Off button and HDD Component of PSU CBL_Power_16 access LED to system board T26139-Y4012-V101 SATA power 5HDD cable from all drives to system board T26139-Y3942-V1 Power adapter SATA to 2x from power cable to backup drive PATA (4pins) power adapter cable for slimline...

  • Page 218: Cabling Plans

    Cables 15.2 Cabling plans Power Supply Access. Bay 1 250W Slimline ODD -E563-V50 Access. Bay 1 ODD/DVD Access. Bay 2 Backup Drive - D3219 PWR1 --------------- Front Panel PWR2 --------------- 2x USB 3.0 FRONT PANEL --- USB FRONT --------- Front USB 1 - -------------- FAN2 SYS ---------- FAN1 SYS ----------...

  • Page 219: Storing Not Used Sata Cables

    Cables 15.3 Storing not used SATA cables Figure 160: Securing not used SATA cables If only two hard disk drives are installed, secure the unused SATA cables in the cable clamps as shown in the figure. Upgrade and Maintenance Manual TX1310 M1...
  • Page 220 Cables Upgrade and Maintenance Manual TX1310 M1...

  • Page 221: Appendix

    Appendix 16.1 Mechanical overview 16.1.1 Server front Figure 161: Front side Pos. Component Optical disk drive Slot for backup drive On/Off button Front USB connectors Upgrade and Maintenance Manual TX1310 M1...

  • Page 222: Server Rear

    Appendix 16.1.2 Server rear Figure 162: Rear side with power supply unit Pos. Component Standard power supply unit Serial connector VGA video connector USB connectors (x 6) Optional expansion cards Standard LAN connectors Upgrade and Maintenance Manual TX1310 M1...

  • Page 223: Server Interior

    Appendix 16.1.3 Server interior Figure 163: Interior Pos. Component Expansion card slots Processor / CPU heat sink / CPU fan TPM board (if installed) HDD 2 HDD 1 System fan 2 (FAN2 SYS on the SEL) HDD 3 HDD 4 Upgrade and Maintenance Manual TX1310 M1...
  • Page 224 Appendix Pos. Component System fan 1 (FAN1 SYS on the SEL) Accessible drive bays Memory modules Power supply unit System board CMOS battery Upgrade and Maintenance Manual TX1310 M1...

  • Page 225: Connectors And Indicators

    Appendix 16.2 Connectors and indicators 16.2.1 Connectors on the system board 16.2.1.1 Onboard connectors Battery DIMM1B DIMM2B DIMM1A Serial DIMM2A PWR1 Intel RESET i210 FAN CPU LAN 1 Front USB Intel LAN 2 i217 Slot 4 USB 1 Slot 3 Intel 5636 Slot 2...
  • Page 226 Appendix No. Print Description PWR1 Power supply connector FRONTPANEL Front panel connector PWR2 Power supply connector RESET Reset FAN CPU Connector for CPU fan HDD LED Connector for HDD LED FAN1 SYS Connector for system fan 1 USB 1 Connector for USB 1 FAN2 SYS Connector for system fan 2 SATA 1-5...

  • Page 227: I/O Panel Connectors

    Appendix 16.2.1.2 I/O panel connectors Figure 165: I/O panel connectors No. Description Standard LAN1 connector Standard LAN2 connector USB 2.0 connectors (x 4) USB 3.0 connectors (x 2) Video connector (blue) Serial connector COM1 (turquoise) The chipset offers two integrated USB 2.0 Rate Matching Hubs (RMHs). That enables lower power requirements and manages the transition of the communication data rate from the high speed of the host controller to the lower speed of USB full speed / low speed devices.

  • Page 228: I/O Panel Indicators

    Appendix 16.2.1.3 I/O panel indicators Figure 166: I/O panel indicators Indicator Status Description green on LAN connection established no LAN connection link/transfer green data transfer in progress flashing yellow on transfer rate 1 Gbit/s LAN speed green on transfer rate 100 Mbit/s transfer rate 10 Mbit/s Note on the onboard LAN controller The system board is equipped with Gigabit Ethernet Controllers of the...

  • Page 229: Connectors And Indicators On The Front Panel

    Appendix 16.2.2 Connectors and indicators on the front panel Figure 167: Front panel connectors and indicators Pos. Component On/Off button / Power-on indicator HDD activity indicator USB 3.0 connectors (x2) The On/Off button is used to switch the server on or off. If the system is running an ACPI-compliant operating system, pressing the On/Off button will perform a graceful shutdown.

  • Page 230: Onboard Settings

    Appendix Indicator Status Description green on server is switched on and running Power-on server is switched off, but mains voltage is indicator present (standby mode) 16.3 Onboard settings Pin 1 Pin 2 DIMM1B Default DIMM2B DIMM1A DIMM2A Pin 2 Pin 1 Pin 2 Pin 1 RCVR...

  • Page 231: Minimum Startup Configuration

    Appendix 16.4 Minimum startup configuration Field Replaceable Units (FRU) If the server does not start up or other problems occur, it may be necessary to take the system down to its most basic configuration in order to isolate the defective component. The minimum startup configuration consists of the following components and cables: Component...
  • Page 232 Appendix CAUTION! Since the system fan is not included in the minimum startup configuration, the server must be shut down immediately after the diagnostic process is complete (POST phase has been passed). The minimum startup configuration must be used exclusively for diagnostic purposes by maintenance personnel, never in daily operation! Upgrade and Maintenance Manual...

Table of Contents