HP 53150A Series Programming Manual page 185

Continued from front matter. . .
Warranty (contd)
HP does not warrant that the
operation of HP products will be
uninterrupted or error free. If
HP is unable, within a
reasonable time, to repair or
replace any product to a
condition as warranted,
customer will be entitled to a
refund of the purchase price
upon prompt return of the
product.
HP products may contain
remanufactured parts
equivalent to new in
performance or may have been
subjected to incidental use.
The warranty period begins on
the date of delivery or on the
date of installation if installed
by HP. If customer schedules or
delays HP installation more
than 30 days after delivery,
warranty begins on the 31st day
from delivery.
Warranty does not apply to
defects resulting from
(a) improper or inadequate
maintenance or calibration,
(b) software, interfacing, parts
or supplies not supplied by HP,
(c) unauthorized modification or
misuse, (d) operation outside of
the published environmental
specifications for the product, or
(e) improper site preparation or
maintenance.
TO THE EXTENT ALLOWED
BY LOCAL LAW, THE ABOVE
WARRANTIES ARE
EXCLUSIVE AND NO OTHER
WARRANTY OR CONDITION,
WHETHER WRITTEN OR
ORAL, IS EXPRESSED OR
IMPLIED AND HP
SPECIFICALLY DISCLAIMS
ANY IMPLIED WARRANTIES
OR CONDITIONS OF
MERCHANTABILITY,
SATISFACTORY QUALITY,
AND FITNESS FOR A
PARTICULAR PURPOSE.
HP will be liable for damage to
tangible property per incident
up to the greater of $300,000 or
the actual amount paid for the
product that is the subject of the
claim, and for damages for
bodily injury or death, to the
extent that all such damages
are determined by a court of
competent jurisdiction to have
been directly caused by a
defective HP product.
TO THE EXTENT ALLOWED
BY LOCAL LAW, THE
REMEDIES IN THIS
WARRANTY STATEMENT
ARE CUSTOMER'S SOLE AND
EXCLUSIVE REMEDIES.
EXCEPT AS INDICATED
ABOVE, IN NO EVENT WILL
HP OR ITS SUPPLIERS BE
LIABLE FOR LOSS OF DATA
OR FOR DIRECT, SPECIAL,
INCIDENTAL,
CONSEQUENTIAL
(INCLUDING LOST PROFIT
OR DATA), OR OTHER
DAMAGE, WHETHER BASED
IN CONTRACT, TORT, OR
OTHERWISE.
For consumer transactions in
Australia and New Zealand: the
warranty terms contained in
this statement, except to the
extent lawfully permitted, do
not exclude, restrict or modify
and are in addition to the
mandatory statutory rights
applicable to the sale of this
product to you.
Assistance
Product maintenance
agreements and other customer
assistance agreements are
available for Hewlett-Packard
products.
For any assistance, contact your
nearest Hewlett-Packard Sales
and Service Office.
Safety Considerations
(contd)
WARNING
INSTRUCTIONS FOR
ADJUSTMENTS WHILE
COVERS ARE REMOVED
AND FOR SERVICING ARE
FOR USE BY SERVICE-
TRAINED PERSONNEL
ONLY. TO AVOID
DANGEROUS ELECTRIC
SHOCK, DO NOT PERFORM
SUCH ADJUSTMENTS OR
SERVICING UNLESS
QUALIFIED TO DO SO.
WARNING
ANY INTERRUPTION OF THE
PROTECTIVE GROUNDING
CONDUCTOR (INSIDE OR
OUTSIDE THE PRODUCT'S
CIRCUITRY) OR
DISCONNECTING THE
PROTECTIVE EARTH
TERMINAL WILL CAUSE
A POTENTIAL SHOCK
HAZARD THAT COULD
RESULT IN PERSONAL
INJURY. (GROUNDING ONE
CONDUCTOR OF A TWO
CONDUCTOR OUTLET IS
NOT SUFFICIENT
PROTECTION.)
Whenever it is likely that the
protection has been impaired,
the instrument must be made
inoperative and be secured
against any unintended
operation.
If this instrument is to be
energized via an
autotransformer (for voltage
reduction) make sure the
common terminal is connected
to the earthed pole terminal
(neutral) of the power source.
Instructions for adjustments
while covers are removed and
for servicing are for use by
trained-personnel only. To avoid
dangerous electric shock, do not
perform such adjustments or
servicing unless qualified to do
so.
For continued protection
against fire, replace the line
fuse(s) of the same current
rating and type (for example,
normal blow, time delay). Do not
use repaired fuses or short
circuited fuseholders.
Acoustic Noise Emissions
LpA<47 dB at operator position,
at normal operation, tested per
EN 27779. All data are the
results from type test.
Geräuschemission
LpA<47 dB am Arbeits
platz, normaler Betrieb, geprüft
nach EN 27779.
Die Angagen beruhen auf
Ergebnissen von
Typenprüfungen.
Electrostatic Discharge
Immunity Testing
When the product is tested with
8kV AD, 4kV CD and 4kV ID
according to
IEC801-2, a system error may
occur that may affect
measurement data made during
these disturbances. After these
occurrences, the system self-
recovers without user
intervention.
7.NC.NL.A.11.03.97.R1.P.CW2C3NC