Main Landing Gear Installation - Freewing F-86 SABRE User Manual

Main landing gear installation

Rear landing gear accessories list
A- Main landing gear metal pin
B - Main landing gear main strut
C -Grub screw (M4•3mm)
D - Spring
E - Rear landing gear damping shaft
F- Pin
G- Rear wheel (050'16mm)
H - Metal spacer
I - Wheel shaft
J - Grub screw (M3•3mm)
K - Assembled main landing gear set
L - Grub screws
(M3•3mm)
M - Landing gear electric retract
N - Assembled landing gear
0 - Screws (PA3•10mm)
P - Main landing gear door
Q - Screw (PM2•4mm)
R - Retract cover
S - Trough
1.lnsert the main landing gear metal pin (A) into
main landing gear main strut (B) and secure it with
two Grub screws (C).
2.lnsert the Spring (D) into the Main landing gear
main strut (B), then insert the Main landing gear
damping shaft (E) into the Main landing gear main
strut (B), press it down, through the side of the
trough of the main landing gear main strut (B),
press the pin (F) to the hole of the main landing
gear damping shaft (E), to prevent the main
landing gear damping shaft (E) from falling off.
3.Put the main wheel (G)and metal spacer (H) on the
wheel shaft (I), then insert the wheel shaft (I) into
the main landing gear damping lever(E), and use
Grub screw (J) to secure it.
4.lnsert the assembled main landing gear set (K)
into the Landing gear electric retract (M), and use 2
Grub screws (L)to secure it.
5.Place the landing gear set (N)on the landing gear
point of main wing , use 4 screws (O) to
hard
secure it, then run the wires through the trough (S).
6.Then use 2 screws (Q) to secure the main landing
gear door (P)to the Main landing gear strut (B ).
7 .Apply glue to attach the retract cover (R) to the
main wing.
Main landing gear accessories list
A- Main gear strut
B -Wheel (050•16mm)
C - Wheel chock
D - Grub screw
(M3•3mm)
E - Rear landing gear installed set
F - Retractable controller
G - Grub screw (M3•3mm)
1. Put the wheel (B) and the wheel lock (C) onto the
main gear strut (A) and use the Grub screw (D) to
secure it.
2. Insert the assembled main landing gear (E) onto the
electric retract (F) and secure it using 2 Grub
screws (G).
3. Use the above diagrams to attach the main landing
gear to the main wing.
Note: . When installing, check that the
flat position of the part is in line with the
screw hole to ensure that the part is
properly seated and will not come loose.
F-86 Sabre
Item No.: FJ2031
Version No.: FJ2031-V01
www.modellmarkt24.ch; www.modellmarkt24.ch;
Full aluminum damping landing gear instructions
·-
��
f!,
G
, -0
.
F ' ' �
I I
� ,
I
C
A
�---------��----� L
�
�··
4S standard version metal landing gear (no damping) instructions
B
C
�-·
.
I
/
D
A
-8-
www.modellmarkt24.de www.modellmarkt24.de
J
E
B
�
N
Note: . When installing, check that the flat
position of the part is in line with the screw
hole to ensure that the part is properly seated
and will not come loose.
)
/
G
EN
M