HP 8112A Operating, Programming And Servicing Manual page 405

PER, 6-7
PERC, 4-8
Performance Tests, 8-1
Period
Specification, 2-2
Period timing, 9-10
Power
cable, 3-3
requirements, 3-2
Requirements, 2-7
Power on, 4-2
Power Supply, 10.2-1
Programming, 6-1
Examples, 7-1
Pulse Width
Specification, 2-2
R
RCL, 6-9
2-
RD, 6-9
Recalibration, 7, 9-1
Remote mode, 6-2
Replaceable Parts
Control Board A2 , A-26
Display Board A5 , A-40
Instrument, A-6
Keyboard A4 , A-37
Main Board Al, A-8
Microprocessor Board A3, A-33
RU, 6-9
s
SD, 6-8
SDC, 6-18
Self test , 2-6
Service request, 2-6
Servicing, 10- 1
Address Decoder, 10.3-2
Burst Control, 10.6- 1
Control Board, 10.5- 1
Control Input, 10.3-2
Display, 10.7-5
Introduction, 10- 1
Keyboard, 10.7-5
Microprocessor, 10.7-1
Output Amplifier, 10.4- 1
Overview, 10.1- 1
Power Supply, 10.2- 1
Self-test, 10. 1-3
Shaper, 10.4-1
Slope Generator, 10.3- 1
Timing, 10.3- 1
Trigger Input, 10.3- 1
Servicing position, 1 0 . 1-3
Shaper IC, 10. 1-1, 10.4-1
Signature Analysis, 10.7-1 5
Slope Error, 6-1 5
Slope Generator I C , 1 0 . 1- 1
Slope IC, 10.3-7
SPD, 6-18
SPE, 6-18
Specifications, 2-1
SRO, 6-9
SRl, 6-9
SRQ, 6-13, 6-17
Standard Parameter Set, 4-4
Status byte, 2-7, 6-13
Status reporting, 6-13
STO , 6-9
SU, 6-8
Switching on, 4-2
Syntax error, 6- 15
T
Tl - T3, 6-6
Test
Recommended test equipment, 1-4
Self-test, 4-2, 1 0 . 1-3
Testing
Self-test, 7-4
Timing adjustment
Delay, 9-1 1
Period, 9-10
Timing error, 6-15
Timing IC, 10.1-1, 10.3-2
Transition Modes, 4- 10
TRE, 6-7
Trigger Controls, 4-6
Triggering examples, 5-1
External burst mode, 5-5
Gate mode, 5-3
Normal mode, 5-1
Trig mode, 5-2
Width mode, 5-4
Trigger mode
Programming, 6-6
Selecting, 4-5
Trigger modes
Specifications, 2-4
Trigger Output, 2-5, 4-6
Trouble shooting, 10.1-3
Troubleshooting
Address Decoder, 10.3-14
Burst Control, 10.6-5
Control Board, 10.5- 1 1
Keyboard, 10.7-17
Main Board, 10.3-14
Microprocessor, 10.7- 15
Output Amplifier, 10.4-14
lndex-3