Mitsubishi F700 Series Instruction Manual page 258

ANALOG VALUE
Object
Object Name
Identifier
1 Output frequency
2 Output current
3 Output voltage
6 Running speed
Converter output
8
voltage
14 Output power
17 Load meter
Cumulative
20
energization time
23 Actual operation time
25 Cumulative power
52 PID set point
54 PID deviation
67 PID measured value 2
200 Alarm history 1
201 Alarm history 2
202 Alarm history 3
203 Alarm history 4
300 Speed scale
*2
310 PID set point CMD
PID measured value
311
CMD
*2
312 PID deviation CMD
398 Mailbox parameter
399 Mailbox value
10007 Acceleration time
10008 Deceleration time
*1 R: Read only W: Read/Write (Commandable values not supported)
*2 If communication speed command source is except for NET, the setting value can be written, but not to be applied.
When both C42 (Pr. 934 ) and C44 (Pr. 935 ) "9999", setting range is smaller coefficient to larger coefficient of C42 (Pr. 934 ) and C44 (Pr. 935 ).
*3
Depending on a value, the writing value and the reading value may not be same at the minimum digit.
Present Value
Access Type
*1
R Represents the output frequency monitor.
R Represents the output current monitor.
R Represents the output voltage monitor.
R Represents the running speed monitor.
R Represents the converter output voltage monitor.
R Represents the output power monitor.
R Represents the load meter monitor.
Represents the cumulative energization time
R
monitor.
R Represents the actual operation time monitor.
R Represents the cumulative power monitor.
R Represents the PID set point monitor.
Represents the PID deviation monitor.
R (minus display is available with reference to 0%,
0.1% increment)
R Represents the PID measured value 2 monitor.
Represents the fault history 1 (the latest fault)
R
monitor.
Represents the fault history 2 (second fault in past)
R
monitor.
Represents the fault history 3 (third fault in past)
R
monitor.
Represents the fault history 4 (fourth fault in past)
R
monitor.
Controls the ratio to the frequency command.
C (Setting range: 0.00 to 100.00)
(Refer to page 244)
Controls the PID set point.
This object is the PID set point during PID operation
C
*2
if Pr. 128 (Pr. 753) = "60 or 61"
(Setting range: 0.00 to 100.00)
Controls the PID measured value.
This object is the PID measured value during PID
C
operation if Pr. 128 (Pr. 753) = "60 or 61"
(Setting range: 0.00 to 100.00)
Controls the PID deviation.
This object is the PID deviation during PID operation
C
*2
if Pr. 128 (Pr. 753) = "50 or 51"
(Setting range: -100.00 to 100.00)
W
Access to the properties which are not defined as
objects are available. (Refer to page 250)
W
W Sets Pr.7 Acceleration time
W Sets Pr.8 Deceleration time
Communication operation and setting
Description
*3
*3
C: Read/Write (Commandable values supported)
Unit
hertz (27)
amperes (3)
volts (5)
revolution-per-
minute
(104)
volts (5)
kilowatts (48)
percent (98)
hours (71)
hours (71)
kilowatt-hours (19)
no-units (95)
no-units (95)
no-units (95)
no-units (95)
no-units (95)
no-units (95)
no-units (95)
percent (98)
no-units (95)
no-units (95)
percent (98)
4
no-units (95)
no-units (95)
seconds (73)
seconds (73)
247