Mitsubishi F700 Series Instruction Manual page 236

[Fault data]
Refer to page 329 for details of fault description.
Data Description Data
H00 No fault H52
H10 E.OC1 H60
H11 E.OC2 H70
H12 E.OC3 H80
H20 E.OV1 H81
H21 E.OV2 H90
H22 E.OV3 H91
H30 E.THT HA0
H31 E.THM HA1
H40 E.FIN HA2
H50 E.IPF HA4
H51 E.UVT HA5
* Refer to the FR-F700 PLC function programming manual for details.
[Run command]
Instruction Bit
Item
Code Length
Run
HFA 8bit
command
Run
command HF9 16bit
(extended)
*1 The signal within parentheses is the initial setting. The description changes depending on the setting of Pr. 180 to Pr. 184, Pr. 187 (input terminal
function selection) (page 117).
*2 The signal within parentheses is the initial setting. Since Jog operation/selection of automatic restart after instantaneous power failure/start self-
holding/reset cannot be controlled by the network, bit 8 to bit 11 are invalid in the initial status. When using bit 8 to bit 11, change the signals with
Pr. 185, Pr. 186, Pr. 188, Pr. 189 (input terminal function selection) (page 123). (Reset can be executed with the instruction code HFD.)
*3 Only forward rotation command and reverse rotation command are available for RS-485 communication using PU connector.
Description Data Description
E.ILF HA6 E.18 *
E.OLT HA7 E.19 *
E.BE HA8 E.20 *
E.GF HB0 E.PE
E.LF HB1 E.PUE
E.OHT HB2 E.RET
E.PTC HB3 E.PE2
E.OPT HC0 E.CPU
E.OP1 HC1 E.CTE
E.OP2 HC2 E.P24
E.16 * HC4 E.CDO
E.17 * HC5 E.IOH
Description
b0: AU (current input selection)
b1: Forward rotation command
b2: Reverse rotation command
b3: RL (low speed operation
command)
*1 *3
b4: RM (middle speed operation
command)
*1 *3
b5: RH (high speed operation
command)
*1 *3
b6: RT (second function selection)
b7: MRS (output stop)
*1 *3
b0:AU (current input selection)
b1:Forward rotation command
b2:Reverse rotation command
b3:RL (low speed operation command)
b4:RM (middle speed operation
command)
*1 *3
b5: RH (high speed operation
command)
*1 *3
b6:RT (second function selection)
b7:MRS (output stop)
*1 *3
b8:JOG (Jog operation)
*2 *3
b9:CS (selection of automatic restart after
instantaneous power failure)
b10: STOP (start self-holding)
b11:RES (reset)
*2 *3
b12:
b13:
b14:
b15:
Communication operation and setting
Data Description
HC6 E.SER
Fault record display example
(instruction code H74)
HC7 E.AIE
HE4 E.LCI
For read data H30A0
HE5 E.PCH
(Previous fault ...... THT)
HE6 E.PID
(Latest fault ...... OPT)
HF1 E.1
b15
HF2 E.2
HF5 E.5
HF6 E.6
HF7 E.7
HFD E.13
*1 *3
[Example 1] H02 Forward rotation
b7
0 0
[Example 2] H00 Stop
b7
0 0
*1 *3
*1 *3
*1 *3
[Example 1] H0002 Forward rotation
b15
0 0 0 0 0
*1 *3
[Example 2] H0800 low speed operation
(When Pr. 189 RES terminal function selection is set to "0")
*2 *3 b15
*2 *3
0 0 0 0 1
b8 b7
0 0 1 1 0 0 0 0 1 0 1 0 0 0
Previous fault Latest fault
(H30) (HA0)
Example
b0
0 0 0 0 1 0
b0
0 0 0 0 0 0
0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0
225
b0
0 0
b0
1 0
b0
0 0
4