Related Manuals for SHOWTEC Dynamic LED V4
Summary of Contents for SHOWTEC Dynamic LED V4
- Page 1 MANUAL ENGLISH Dynamic LED Ordercode: 43056 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
-
Page 2: Table Of Contents
Dynamic LED Table of contents Warning ....................................2 Safety Instructions ................................. 2 Operating Determinations ............................4 Rigging .................................... 4 Connection with the mains ............................5 Return Procedure ................................6 Claims ....................................6 Description of the device ..............................7 Overview ..................................7 Backside .................................. -
Page 3: Warning
Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing. Your shipment includes: ● Showtec Dynamic LED ● IEC Power cable (1,5 m) ●... - Page 4 ● If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Showtec dealer for service.
-
Page 5: Operating Determinations
Dynamic LED ● This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to earth. ● Repairs, servicing and electric connection must be carried out by a qualified technician. ● WARRANTY: Till one year after date of purchase. Operating Determinations ●... -
Page 6: Connection With The Mains
Dynamic LED The Dynamic LED can be placed on a flat stage floor or mounted to any kind of truss with a clamp. Improper installation can cause serious injuries and/or damage of property! Connection with the mains Connect the device to the mains with the power-plug. Always check if the right color cable is connected to the right place. -
Page 7: Return Procedure
Dynamic LED Return Procedure Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility. Call Highlite 0031-455667723 or mail aftersales@highlite.nl and request an RMA prior to shipping the fixture. -
Page 8: Description Of The Device
Dynamic LED Description of the device Features The Dynamic LED is a light effect with high output and great effects. ● 42 LED Matrix patterns ● 4-in-1 Light effect ● Wide beam angle ● Input voltage: 90-240V AC, 50/60Hz ● Power consumption: 38W (full output) ●... -
Page 9: Backside
Dynamic LED Backside Fig. 02 03) 3-pin DMX signal connector IN 04) 3-pin DMX signal connector OUT 05) Ground/earth connection 06) IEC Power connector IN + Fuse T1L/250V 07) LED display + menu buttons 08) Safety eye Installation Remove all packing materials from the Dynamic LED. Check if all foam and plastic padding is removed. Connect all cables. -
Page 10: Control Modes
Dynamic LED Control Modes There are 6 modes: • Auto Program • Built-in programs • Static Color (manual) • Sound-controlled • Master/slave • DMX-512 (2CH or 3CH) One Dynamic (Auto Program, Built-in programs and Static Color) 01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). -
Page 11: Multiple Dynamics (Dmx Control)
Dynamic LED Multiple Dynamics (DMX Control) 01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) Use a 3-pin XLR cable to connect the Dynamics and other devices. 04) Link the units as shown in Fig. -
Page 12: Fixture Linking
Dynamic LED Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support. -
Page 13: Control Panel
Dynamic LED Control Panel A) LED Display Mode Button C) Setup button D) Up button Down button Fig. 05 Control Mode The fixtures are individually addressed on a data-link and connected to the controller. The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it, the controller will display the saved DMX address, next time.) DMX Addressing The control panel on the back side of the device allows you to assign DMX fixture addresses, which is the... -
Page 14: Menu Overview
Dynamic LED Menu Overview Main Menu Options Built-in programs Auto run program DMX Address /DMX Channels Slave Mode Sound-controlled Mode Static Color Mode Ordercode: 43056... -
Page 15: Built-In Programs
Dynamic LED 1. Built-in programs With this menu you can choose between several Built-in programs and setting the speed and strobe. 01) Press the Mode button until the display shows 02) Press the Up and Down buttons to choose between 42 types of built-in programs 03) Press the Setup button to open the submenu from the chosen built-in program. -
Page 16: Sound-Controlled Mode
Dynamic LED 5. Sound-controlled Mode With this menu you can set the Sound-controlled programs. 01) Press the Mode button until the display shows 02) Press the Setup button to open the submenu, you can choose between 2 options: Sound program 1: the LEDs will keep running for 5 seconds after the music has been stopped Sound program 2: the LEDs immediately stop running when the music stops 03) Hold the Up or Down button for 3 seconds to switch between program 1 or program 2. -
Page 17: Dmx Channels
Dynamic LED DMX Channels 3 channels Channel 1 – Built-in programs No function Program 1 6-11 Program 2 12-17 Program 3 18-23 Program 4 24-29 Program 5 30-35 Program 6 36-41 Program 7 42-47 Program 8 48-53 Program 9 54-59 Program 10 60-65 Program 11... -
Page 18: Channels
Dynamic LED Channel 3 – Strobe (CH1 must be set between 1-251 0-255 Strobe flash frequency, from slow to fast (0-20 Hz) Channel 3 – No function (CH1 must be set between 252-255 0-255 No function 2 channels Channel 1 – Preset colors No function 1-22 23-45... -
Page 19: Maintenance
Suspect three potential problem areas as: the power supply, LEDs, the fuse. 01) Power supply. Check that the unit is plugged into an appropriate power supply. 02) The LEDs. Return the Dynamic to your Showtec dealer. 03) The fuse. Replace the fuse. See page 18 for replacing the fuse. - Page 20 Dynamic LED Problem Probable cause(s) Solution No power to the fixture • Check if power is switched on and One or more cables are plugged in fixtures do not function at all Primary fuse blown. • Replace fuse. Fixtures reset The controller is not connected.
-
Page 21: Product Specifications
Dynamic LED Product Specifications Model: Showtec Dynamic LED Input Voltage: 90-240V AC, 50/60Hz Power consumption: 38W (full output) DMX linking: 30 pcs Protection rate: IP-20 Fuse: T1L/250V Dimensions: 930 x 150 x 155 mm (LxWxH) (incl. bracket) Weight: 4,4 kg... -
Page 22: Dimensions
Dynamic LED Dimensions Ordercode: 43056... -
Page 23: Notes
Dynamic LED Notes Ordercode: 43056... - Page 24 ©2017 Showtec...