1. Manuals
  2. Brands
  3. CEStronics Manuals
  4. Receiver
  5. Omega Flex
  6. Manual

CEStronics OMEGA FLEX Manual

Programming adaptor
Hide thumbs Also See for OMEGA FLEX:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Quick Manual, Fitting and Operating Instructions
OMEGA FLEX Programming Adaptor
Programming Adaptor (Cylinder)
Programming Adaptor (ILS/SIS)
Programming Adaptor and Firmware-updates
English
Version VA
BRO2268

Advertisement

Table of Contents
loading

Related Manuals for CEStronics OMEGA FLEX

Summary of Contents for CEStronics OMEGA FLEX

  • Page 1 OMEGA FLEX Programming Adaptor Programming Adaptor (Cylinder) Programming Adaptor (ILS/SIS) Programming Adaptor and Firmware-updates English Version VA BRO2268...

  • Page 2: Table Of Contents

    Contents 1 About this manual 1.1 Design features 1.2 Target group of this manual 1.3 Manufacturer and Service 1.4 Notes on trademark protection 2 For your safety 2.1 Declaration of Conformity 2.2 Intended use 2.3 Basic safety instructions 2.4 Notes on dealing with batteries 2.5 Manufacturer's warranty 3 Programming Adaptor 3.1 About Programming Adaptor...

  • Page 3: About This Manual

    Marks warnings in step-by-step instructions and specially important information 1.2 Target group of this manual This manual is intended for administrators of CEStronics locking systems. The necessary expertise regarding the intended use of the product are presumed for the use of this manual.

  • Page 4: For Your Safety

    2   For your safety 2 For your safety 2.1 Declaration of Conformity The Declaration of Conformity is available online via www.ces.eu 2.2 Intended use The Programming Adaptor is used to program electronic cylinders and handle sets. It is exclusively intended this purpose and may only be used for this. All other uses are considered as improper use and may lead to material damages.

  • Page 5: Notes On Dealing With Batteries

    Do not use the handle set near heat sources. 2.4 Notes on dealing with batteries Only the batteries specified by CES for electronic cylinders may be used in OMEGA FLEX elec tronic cylinders (Panasonic CR2 Industrial Lithium 3,0 V 850 mAh).
  • Page 6 2   For your safety All technical data and features are subject to change without prior notice. All information and data contained in this document is subject to change without prior notice. No part of this document may be copied or transmitted for any purposes whatsoever without the express written permission from the C.Ed.

  • Page 7: Programming Adaptor

    3   Programming Adaptor 3 Programming Adaptor 3.1 About Programming Adaptor A Programming Adaptor is a programming device with which Firmware updates can be transmitted Replacement parts can be coupled with existing locking devices (“Pairing”) There are two types of Programming Adaptors: Programming Adaptor (Electronic cylinder) For the programming of electronic cylinders Programming Adaptor (ILS/SIS)

  • Page 8: Scope Of Delivery Programming Adaptor (Ils/Sis)

    3   Programming Adaptor 3.3 Scope of delivery Programming Adaptor (ILS/SIS) Programming Adaptor (ILS/SIS) USB cable Connecting cable Programming Adaptor Page 8 of 30...

  • Page 9: Executing Firmware Updates For Cylinder

    4   Executing firmware updates for Cylinder 4 Executing firmware updates for Cylinder Required programming device: Programming Adaptor (Cylinder) If you are updating a dual cylinder, you must update both knobs of the cylinder. 1. Connect the Programming Adaptor to your PC. If you are connecting the programming adaptor for the first time to the PC, the driver will be installed automatically now.
  • Page 10 4   Executing firmware updates for Cylinder 2. Remove the KNOB SLEEVE 3. Remove the KNOB If you touch the knob electronic, it can be damaged. Therefore, hold the knob electronics only within the marked area: This completes the knob dismantling. 3.
  • Page 11 4   Executing firmware updates for Cylinder If you touch the knob electronic, it can be damaged. Therefore, hold the knob electronics only within the marked area: 2. Push the knob down and simultaneously turning it clockwise. The knob thus engages in the Programming Adaptor.
  • Page 12 4   Executing firmware updates for Cylinder Starting the firmware-Update 1. Open the program OMEGA F IRMWARE PDATE 2. Select the desired device category. 3. Select the desired product. 4. Select the desired programming device with which you want to transmit the firmware update.
  • Page 13 4   Executing firmware updates for Cylinder Make sure that the large spring lies over the large groove and the small spring over the small groove. 2. Insert the with correct polarity. BATTERIES Use only Panasonic CR2 Industrial Lithium 3,0 V 850 mAh batteries.
  • Page 14 4   Executing firmware updates for Cylinder Make sure that the is screwed KNOB SLEEVE flush! The knob is assembled now. The knob is now ready for operation with the new firmware. In the case of a dual cylinder, make sure that you update both knobs of the cylinder. Programming Adaptor Page 14 of 30...

  • Page 15: Executing Firmware Updates For Long Shield Ils

    5   Executing firmware updates for Long shield ILS 5 Executing firmware updates for Long shield ILS Required programming device: Programming Adaptor (ILS/SIS) 1. Connect the Programming Adaptor to your PC. If you are connecting the Programming Adaptor for the first time to the PC, the driver will be installed automatically now.
  • Page 16 5   Executing firmware updates for Long shield ILS 3. Remove the from the BATTERY MODULE ASSEMBLY PLATE 4. Use the slot head screwdriver to unscrew the cable brackets and disconnect the cables. 5. Use the wrench to loosen the nuts and remove nuts, washers and, if present, the spring clip.
  • Page 17 5   Executing firmware updates for Long shield ILS 6. Pull off the on the outer side of the OUTSIDE FITTING door. Remove e-module Removal of e-module (using a shield for long-hole bores as an example) 1. Remove the fixing screws from the outside fitting.
  • Page 18 5   Executing firmware updates for Long shield ILS 3. Push out the from the MODULE OUTSIDE FITTING 4. Remove the plug from the MODULE 3. Connect one of the both sockets of the Programming Adaptor to the e-module. Connecting the e-module to the Programming Adaptor Connecting the e-module to the Programming Adaptor 1.
  • Page 19 5   Executing firmware updates for Long shield ILS 4. Start the update program OMEGA Firmware Update. Starting the firmware-Update 1. Open the program OMEGA F IRMWARE PDATE 2. Select the desired device category. 3. Select the desired product. 4. Select the desired programming device with which you want to transmit the firmware update.
  • Page 20 5   Executing firmware updates for Long shield ILS 2. Insert the in the MODULE OUTSIDE FITTING 3. Make sure that the e-module is installed flush with the handle set. 4. Press the wiring harness into the recess so that it is not squashed or pinched. Before reattaching the , all ASSEMBLY PLATE...
  • Page 21 5   Executing firmware updates for Long shield ILS Cable routing for Long shield bores 5. Guide the cables through the top elongated hole of the MOUNTING PLATE Pull the cables so far that they are not pinched under the mounting plate. Cable routing for rosette bores 5.
  • Page 22 5   Executing firmware updates for Long shield ILS A detailed assembly instruction for different assembly types can be found in the Manual for the Long shield ILS. Programming Adaptor Page 22 of 30...

  • Page 23: Executing Firmware Update For Smart Shield Sis

    6   Executing firmware update for Smart shield SIS 6 Executing firmware update for Smart shield SIS Required programming device: Programming Adaptor (ILS/SIS) 1. Connect the Programming Adaptor to your PC. If you are connecting the Programming Adaptor for the first time to the PC, the driver will be installed automatically now.
  • Page 24 6   Executing firmware update for Smart shield SIS 4. Remove the batteries. Remove the batteries only by hand. Do not use any foreign objects for this. 5. Remove the MODULE 3. Connect the e-module to the Programming Adaptor. Connecting the e-module to the Programming Adaptor Connecting e-module to the Programming Adaptor 1.
  • Page 25 6   Executing firmware update for Smart shield SIS If the e-module lights up red-green simultaneously, it is ready for the update. 4. Start the update program OMEGA Firmware Update. Start firmware-Update 1. Open the program OMEGA F IRMWARE PDATE 2. Select the desired device category. 3.
  • Page 26 6   Executing firmware update for Smart shield SIS 2. Insert the batteries with correct polarity IN THE holder. BATTERY Use only Energizer Ultimate Lithium 1,5V AAA batteries. The correct polarity is indicated in the BATTERY module. 3. Make cable connection between e-module and the bracket by plugging the cable into the vertical cable connector.

  • Page 27: Maintenance

    7   Maintenance 7 Maintenance 7.1 Device care You can clean the programming adaptor with a soft, slightly damp cloth. 7.2 Service For service assistance please contact your CES partner. Programming Adaptor Page 27 of 30...

  • Page 28: Notes On Disposal

    Packaging The packagings of the OMEGA FLEX components are made from environmentally friendly, reusable materials. Specifically, these are: Outer packaging and inlays made of cardboard...

  • Page 29: Technical Data

    9   Technical data 9 Technical data 9.1 Equipment features Article numbers Programming Adaptor (Cylinder) Programming Adaptor (ILS/SIS) Connection values USB connection, Type A/B Permissible temperature -20 °C to +70 °C Prohibited atmospheres Not suitable for operation in corrosive atmosphere (Chlorine, Ammonia, Lime water) Permissible air humidity 0 …...
  • Page 30 C. Ed. Schulte GmbH United Kingdom Zylinderschlossfabrik CES Security Solutions Ltd. Friedrichstraße 243 Unit 4 Kendon Business Park D-42551 Velbert Maritime Close, Medway City Estate +49 2051 204 0 Rochester, Kent ME2 4JF +44 1 634713369 +49 2051 204 229 +44 1 634786833 info@ces.eu info@uk.ces.eu...

Table of Contents