Nice NDA001 Programming Manual page 14

radio channel no.2
radio channel no.3
radio channel no.4
Control unit status (0x1f)
output 2
In this output the user can select one of the functions specified in Table 2.
output 3
In this output you can choose one of the functions described in Table 2, except for the "flasher 24" and "control unit status" functions.
electric lock time
This parameter is expressed in seconds and can be set with a value from 0.1 to 10 sec.; the factory setting is 2 sec. This function enables programming on
the Control unit of the required time interval to pass between the end of a Closing manoeuvre and the start of an Opening manoeuvre.
suction cup time
This parameter is expressed in seconds and can be set with a value from 0.1 to 10 sec.; the factory setting is 2 sec. This function enables programming on
the Control unit of the required time interval to pass between the end of a Closing manoeuvre and the start of an Opening manoeuvre, when the suction cup
is disengaged.
Courtesy light time
This parameter is expressed in seconds and can be set with a value from 0 to 250 sec.; the factory setting is 60 sec. This function programs the courtesy
light on time for the various outputs.
It disables short circuit control on outputs (0xa6)
This parameter is of the ON/OFF type; the factory setting is "OFF". When this function is set to ON it allows the short circuit control on outputs 1 and 2 to
be disabled
Inverter (inverters only) (0xfe)
• Inverter mode (0xad)
This parameter is of the ON / OFF type; the factory setting is "OFF". When set to "ON", it activates the operating logic of motors with MEIN series on-board
inverters. Important – After activating this function, you must run device learning again.
Speed management (inverters only)
• Open speed (0x42)
This parameter can be set with a value from 20% to 180%; the factory setting is 100%. The function enables programming of the required motor speed dur-
ing an Opening manoeuvre. Important – After setting this parameter, you must run a few manoeuvres to allow the system to recalculate the decelerations.
• opening deceleration (0x45)
This parameter can be set with a value from 20% to 180%; the factory setting is 45%. The function enables programming of the required motor speed dur-
ing the initial deceleration phase of an opening manoeuvre. Important – After setting this parameter, you must run a few manoeuvres to allow the system to
recalculate the decelerations.
• closing speed (0x43)
This parameter can be set with a value from 20% to 180%; the factory setting is 100%. The function enables programming of the required motor speed
during a Closing manoeuvre. Important – After setting this parameter, you must run a few manoeuvres to allow the system to recalculate the decelerations.
• closing deceleration speed (0x46)
This parameter can be set with a value from 20% to 180%; the factory setting is 45%. The function enables programming of the required motor speed dur-
ing the initial deceleration phase of an opening manoeuvre. Important – After setting this parameter, you must run a few manoeuvres to allow the system to
recalculate the decelerations.
If this radio channel is set for the configuration of output 1 (flash), this channel
is activated when a command is set with the transmitter. This mode is useful
if installing external devices (for example, an auxiliary light) in the same system
to be controlled with a single transmitter.
WARNING – If this channel is not free on the control unit receiver, as previously
memorised with a command, the control unit activates exclusively the pro-
grammed output when the channel is activated with the transmitter, ignoring
the command to the motor.
Output active 24Vdc / max 10 W
If this radio channel is set for the configuration of output 1 (flash), this channel
is activated when a command is set with the transmitter. This mode is useful
if installing external devices (for example, an auxiliary light) in the same system
to be controlled with a single transmitter.
WARNING – If this channel is not free on the control unit receiver, as previously
memorised with a command, the control unit activates exclusively the pro-
grammed output when the channel is activated with the transmitter, ignoring
the command to the motor.
Output active 24Vdc / max 10 W
If this radio channel is set for the configuration of output 1 (flash), this channel
is activated when a command is set with the transmitter. This mode is useful
if installing external devices (for example, an auxiliary light) in the same system
to be controlled with a single transmitter.
WARNING – If this channel is not free on the control unit receiver, as previously
memorised with a command, the control unit activates exclusively the pro-
grammed output when the channel is activated with the transmitter, ignoring
the command to the motor.
Output active 24Vdc / max 10 W
This output copies the operation of the Bluebus led which determines the
status of the control unit, including the diagnostics. In addition, the output is
deactivated when the safety chain (ALT, motor thermal cutout, SAFE, STOP
key on cover) is interrupted.
Output active 24 V DC / max 10 W