Related Manuals for Nice SD-70-20 3 400
Summary of Contents for Nice SD-70-20 3 400
- Page 1 Nice Gearmotors for sectional doors EN - Instructions and warnings for installation...
- Page 2 GENERAL WARNINGS: SAFETY - INSTALLATION - USE (original instructions in Italian) CAUTION Important safety instructions. Observe all the instructions as improper installation may cause serious damage CAUTION Important safety instructions. It is important to comply with these instructions to ensure personal safety. Store these instructions •...
- Page 3 must be opened and closed with the braken open (released). GENERAL DANGER WARNINGS AND - On doors not balanced with weights, the brake is to be released PREVENTIVE SAFETY only for checking purposes with the door in the low position for safety reasons.
-
Page 4: Limit Switch Setting
LIMIT SWITCH SETTING STAR/DELTA VOLTAGE CONNECTION The door must be balanced in all positions when assembling and Warning! Danger of death due to electric shock. balancing with the weights according to the procedures prescribed by the standards. Correct balancing is ascertained by manually Before starting the assembly operations, exclude the voltage from opening and closing the door with identical activation force in both the conductors and check that they are really equal to zero. -
Page 5: Annual Check
TECHNICAL SPECIFICATIONS NOTE: all the technical characteristics indicated refer to a temperature falling between -5°C and +40°C. • Nice reserves the right to change all the modifications to the product it deems necessary at any time, but keeping the functions and intended use unaltered. - Page 6 Assembly of gearmotor shaft using Application of support for suspended or fixing screw or ring vertical assembly MOTOR MOTOR WALL WALL GREEN GREEN English – 5...
-
Page 7: Manual Release
MOTOR ROOF MOTOR ROOF GREEN GREEN Manual release Emergency maneuver 6 white Additional limit switch 1 CLOSE 5 green Additional limit switch 1 OPEN 4 red Safety limit switch CLOSE 3 white Limit switch CLOSE 2 red Safety limit switch OPEN 1 green Limit switch OPEN Mechanical limit switch setting 6 –... -
Page 8: Delta Connection
9. Use only if the chain slips! Turn the handle clockwise until the operational efficiency of the chain is restored! Electronic limit switch Electronic limit switch ENAS003 type Kostal type Motor power supply terminal Motor power supply terminal ... - Page 9 DIMENSIONED DRAWINGS OF GEARMOTORS FOR SECTIONAL DOORS SD_70-20 1_230 E Ø 25,4 6,35 SD_70-20 1_230 KE Ø 25,4 6,35 8 – English...
- Page 10 DIMENSIONED DRAWINGS OF GEARMOTORS FOR SECTIONAL DOORS SD_70-20 1_230 KU Ø 25,4 6,35 English – 9...
- Page 11 DIMENSIONED DRAWINGS OF GEARMOTORS FOR SECTIONAL DOORS SD-70-20 3_400 E Ø 25,4 6,35 SD-70-20 3_400 KE Ø 25,4 6,35 10 – English...
- Page 12 DIMENSIONED DRAWINGS OF GEARMOTORS FOR SECTIONAL DOORS SD-70-20 3_400 KU Ø 25,4 6,35 English – 11...
- Page 13 DIMENSIONED DRAWINGS OF GEARMOTORS FOR SECTIONAL DOORS SD-80-30-E Ø 25,4 6,35 SD-80-30-KE Ø 25,4 6,35 12 – English...
- Page 14 DIMENSIONED DRAWINGS OF GEARMOTORS FOR SECTIONAL DOORS SD-80-30-KU Ø 25,4 6,35 English – 13...
- Page 15 DIMENSIONED DRAWINGS OF GEARMOTORS FOR SECTIONAL DOORS SD_100-24-3_400-E Ø 25,4 6,35 SD_100-24-3_400-KE Ø 25,4 6,35 14 – English...
- Page 16 DIMENSIONED DRAWINGS OF GEARMOTORS FOR SECTIONAL DOORS SD_100-24-3_400-KU Ø 25,4 6,35 SD_120-20-3_400-E Ø 25,4 6,35 English – 15...
- Page 17 DIMENSIONED DRAWINGS OF GEARMOTORS FOR SECTIONAL DOORS SD_120-20-3_400-KE Ø 25,4 6,35 SD_120-20-3_400-KU Ø 25,4 6,35 16 – English...
- Page 18 DIMENSIONED DRAWINGS OF GEARMOTORS FOR SECTIONAL DOORS SD_140-20-3_400-E Ø 25,4 6,35 Ø 31.75 6,35 When assembling gearmotors with 31.75 mm diameter shaft from the left, the tab is to be blocked only with a fixing ring because using a screw could break the shaft.
- Page 19 DIMENSIONED DRAWINGS OF GEARMOTORS FOR SECTIONAL DOORS SD_140-20-3_400-KE Ø 25,4 6,35 Ø 31,75 6,35 When assembling gearmotors with 31.75 mm diameter shaft from the left, the tab is to be blocked only with a fixing ring because using a screw could break the shaft.
- Page 20 DIMENSIONED DRAWINGS OF GEARMOTORS FOR SECTIONAL DOORS SD_140-20-3_400-KU Ø 25,4 6,35 Ø 31,75 6,35 When assembling gearmotors with 31.75 mm diameter shaft from the left, the tab is to be blocked only with a fixing ring because using a screw could break the shaft.
-
Page 21: Ec Declaration Of Conformity
EC Declaration of Conformity and declaration of incorporation as “partly completed machinery” The EC Declaration of Conformity can be downloaded from our website www.niceforyou.com Nice S.p.A. Via Pezza Alta, 13 31046 Oderzo TV Italy www.niceforyou.com info@niceforyou.com...