Command Configuration - Nice NDA001 Programming Manual

COMMAND CONFIGURATION

This item covers the command categories associable with inputs 1 - 2 - 3 (refer to the section "input configuration - Table 1" to check the commands avail-
able). Each command category features various operating modes as described in a table (1-A, 1-B, etc.):
Step-by-step
In this command category the user can select one of the operating modes specified in Table 1-A.
MODE
Industrial mode
Open - stop - close - stop
Open - Stop - Close - Open
Open - Close - Open - Close
Apartment block 1 step-by-step
Apartment block 2 step-by-step
Step-by-step 2
Hold-to-run
Partial open
In this command category the user can select one of the operating modes specified in Table 1-B.
MODE
Open - stop - close - stop
Open - Stop - Close - Open
Open - Close - Open - Close
Apartment block 1 step-by-step
Apartment block 2 step-by-step
Hold-to-run
Industrial mode
Open
In this command category the user can select one of the operating modes specified in Table 1-C.
MODE
Open - Stop - Open
Apartment block 1
Apartment block 2
Open 2
Hold-to-run Open
Close
In this command category the user can select one of the operating modes specified in Table 1-D.
TABLE 1-A: COMMAND CONFIGURATION
DESCRIPTION
This runs the sequence "open in semiautomatic- close in hold-to-run".
This executes the above sequence.
Operating mode set in factory (Input 1 - "step-by-step" command). This ex-
ecutes the above sequence.
This executes the above sequence.
Runs the sequence "close - stop - open - open", until it reaches the fully open
position. Note – If another command is sent after this one, the application
executes the Closing manoeuvre with the same sequence.
Runs the sequence "close - stop - open - open" until the fully open position
is reached. Note – If another command is sent after this one, the application
executes the Closing manoeuvre with the same sequence.
Important – When sending a command, if the transmitter key is held down for
more than 2 seconds, the control unit activates a Stop.
This executes the sequence "open - stop - close - open". Important – When
sending a command, if the transmitter key is held down for more than 2 sec-
onds, the control unit activates a "partial open 1" command (input configura-
tion > Table 1).
The Opening or Closing manoeuvre is executed exclusively if the transmitter
key is held down (hold-to-run).
TABLE 1-B: COMMAND CONFIGURATION
DESCRIPTION
Operating mode set in factory. This executes the above sequence.
This executes the above sequence.
This executes the above sequence.
This executes the sequence "close - stop - partial open 1- partial open 1"
until the position is reached as programmed in the function "Partial Open 1".
Note – If another command is sent after this one, the application executes the
Closing manoeuvre with the same sequence.
This executes the sequence "close - stop - partial open 1 - partial open 1"
until the position is reached as programmed in the function "Partial Open 1".
Note – If another command is sent after this one, the application executes
the Closing manoeuvre with the same sequence. Important – When sending
a command, if the transmitter key is held down for more than 2 seconds, the
control unit activates a Stop.
The Partial open 1 or Closing manoeuvre is executed exclusively if the trans-
mitter key is held down (hold-to-run).
This runs the sequence "open in semiautomatic- close in hold-to-run".
TABLE 1-C: COMMAND CONFIGURATION
DESCRIPTION
Operating mode set in factory (Input 2 - "open" command). This executes the
above sequence.
This executes the sequence "open - open". Important – When sending a com-
mand, if the transmitter key is held down for more than 2 seconds, the control
unit activates a Stop.
This executes the Opening sequence.
Important – When sending a command, if the transmitter key is held down for
more than 2 seconds, the control unit activates a "partial open 1" command
(input configuration > Table 1).
The Opening manoeuvre is executed exclusively if the transmitter key is held
down (hold-to-run).