Overview; Specifications; Additional Models; Installation Instructions - Altronix HubSat4WPV Installation Manual

Altronix HubSat4WPV Passive UTP Transceiver Hub with Integral Camera Power transmits UTP video, RS422/
RS485 data and power over a single CAT-5 or higher structured cable . Unit provides 4 camera channels in a wall
mount enclosure . Video transmission range is up to 750 ft . max . per channel . Units are compatible with AC and/
or DC fixed or PTZ cameras when utilizing Altronix HubWayAv, HubWayAv2, HubWayDv or HubWayDvi
Video Balun/Combiners . In addition, the unit features individually selectable 24VAC or 28VAC PTC protected
outputs with surge suppression . Optionally, the HubSat4WPV can be used as an accessory module to transmit
video from up to 4 cameras over a single CAT-5 or higher structured cables back to the HubWay, HubWayLD
or HubWayLDH Passive and Active UTP Transceiver Hubs . In addition, the HubSat4WPV provides power to
these cameras locally to eliminate the possibility of voltage drop associated with long cable runs .
Input:
• 220VAC, 50/60Hz, 0 .7A .
Video:
• Four (4) channels of quality video over twisted pair
up to a distance of 750 ft . per channel .
• Four (4) 75 Ohm video outputs .
Data:
• RS422/RS485 data input .
Power:
• Individually selectable 24VAC or 28VAC power
outputs with OFF position .
• Unit provides up to 1A max . per channel not to
exceed a total of 4A maximum current .
HubSat42WPV
• HubSat4WPV with four (4) HubWayAv
Video Balun/Combiners for 24VAC Cameras .
WARNING: To reduce the risk of fire or electric shock do not expose the unit to rain or moisture.
This installation should be made by qualified service personnel and should conform to all local codes.

HubSat4WPV Outdoor Passive UTP Transceiver Hub with Integral Camera Power.

Unit should be installed in accordance with The National Electrical Code and all applicable Local Regulations .
1 . Remove back plate inside the enclosure by removing the four (4) mounting screws (Fig. 4, pg. 8) .
2 . Mark and drill desired knockouts on the enclosure to facilitate wiring (Fig. 1, pg. 6).
3 . Secure back plate inside the enclosure with the four (4) mounting screws (Fig. 4b, pg. 8) .
4 . Unit can be wall or pole mounted .
Wall Mount:
- Mark and drill holes to line up with the top and bottom holes of the enclosure flange .
- Secure enclosure with appropriate fasteners (Enclosure Dimensions, pg. 12) .
Pole Mount:
- Refer to the detailed pole mount instructions (pg. 10).
Secure enclosure to earth ground .
4 . Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 4a, pg. 8) .
5 . Connect 220VAC 50/60Hz to the black and white flying leads of open frame transformer . Secure ground
wire (Green) to earth ground (Fig. 4, pg. 8) .
6 . S elect 24VAC or 28VAC power output for each of the Channels 1-4 on HubSat4WPV (Fig. 4, pg. 8) with
the corresponding output voltage switches . Select OFF position when servicing or installing individual
cameras (Fig. 2d, pg. 6) .
7 . Connect the BNC video outputs marked [Video 1-4] on HubSat4WPV to the corresponding video inputs
on the head end equipment (DVR) (Fig. 2a, pg. 6) .
8 . Connect terminals marked [+ DATA –] on HubSat4WPV (polarity must be observed) to the RS422/RS485
output of the head end equipment (DVR) (Fig. 2f, pg. 6) . When using fixed cameras disregard this step .
HubSat4WPV

Overview:

Specifica tions:
Power (cont'd):
• PTC protected outputs are rated @ 1A per channel .
• Surge suppression .
Visual Indicators:
• Four (4) power LED indicators .
Enclosure Dimensions (H x W x D approx.):
Optional Accessories:
• Video Balun/Combiners:

Additional Models:

HubSat43WPV
• HubSat4WPV with four (4) HubWayDv

Installation Instructions:

12" x 8" x 6" (304 .8mm x 203 .2mm x 152 .4mm)
- HubWayAv - for use with 24VAC cameras .
- HubWayAv2 - for use with 24VAC cameras .
- HubWayDv - for use with 12VDC cameras .
- HubWayDvi - for use with non-isolated
12VDC cameras .
Video Balun/Combiners for 12VDC Cameras .
- 3 -