Related Manuals for Optical Systems Design OSD2892
Summary of Contents for Optical Systems Design OSD2892
-
Page 1: Index
Quick Start Guide OSD2892 MANAGED 36 x 10/100/1000BASE-T & 4 x 10G SFP ETHERNET SWITCH... -
Page 3: Table Of Contents
ESCRIPTION NS .......................... 4 PPLICATIO FEATURES AND BENEFITS ....................4 TECHNICAL SPECIFICATIONS ................... 4 INSTALLATION........................6 OSD2892 FRONT AND REAR PANELS................. 7 FRONT PANEL ........................7 REAR P ..........................7 ANEL POWER SUPPLY CONNECTIONS ..................7 LED INDICATORS ........................8 FITTING SFP CONNECTORS .................... -
Page 4: Introduction
Start Guide is designed to guide you through the installation and basic software functions. 2 TECHNICAL SUMMARY BRIEF DESCRIPTION The OSD2892 is an L2/L3 managed 36 port 10/100/1000BASE-T and 4 port 10G SFP Ethernet Switch. Please see OSD2892 datasheets for options available. APPLICATIONS ▲... -
Page 5: Technical Specifications
TABLE 1: TECHNICAL SPECIFICATIONS SPECIFICATION PERFORMANCE IEEE802.3i/802.3u/802.3ab, 10/100/1000Base-T Ethernet Electrical Data Interface Electrical Data Connector RJ45 on the fixed copper ports for OSD2892 and OSD2892P IEEE802.3af: 47 to 55V @ 0.35Amp maximum OSD2892P PoE IEEE802.3at: 47 to 55V @ 0.70Amp maximum... -
Page 6: Installation
OPTICAL OUTPUT OPERATION WARNING: Laser Safety: Class 1 Laser Product (SFP) per IEC 60825-1:2014 standard. Class 1 The OSD2892 is a Class 1 laser product when SFP are fitted PRECAUTIONS ▲... -
Page 7: Osd2892 Front And Rear Panels
13. PSU 1 Power Supply Input/Fuse/Switch 5 Power Supply Connections There are various power options for the OSD2892. Refer to Table 1 Power Options (Figure 3 has OSD2892AC version shown). Power is connected to the rear of the unit. Fuse: 1A 250V Anti-Surge, 5x20mm. -
Page 8: Led Indicators
Off – No Connection • Fiber Port Status Duplex Mode: Green – Full Duplex • Off – No Connection • Status Mode: Green – Connection established • Off – No Connection • DOC ID: 10118602 PAGE 8 OSD2892 QUICK START GUIDE... -
Page 9: Fitting Sfp Connectors
Removing SFP – Remove fiber connector. Pull the SFP lever down to unlock SFP from housing. Using the lever, gently pull the SFP out. Fiber SFP Inserting Removing FIGURE 4: FITTING/REMOVING SFP CONNECTORS DOC ID: 10118602 PAGE 9 OSD2892 QUICK START GUIDE... -
Page 10: Cli Overview
OPTICAL SYSTEMS DESIGN 8 CLI OVERVIEW CONNECT TO CLI The Silicon Laboratories CP210x VCP Drivers is required to be installed on the PC before connecting the switch. DOC ID: 10118602 PAGE 10 OSD2892 QUICK START GUIDE... -
Page 11: Cli Command For Ip Configuration
The Command Line Interface (CLI) is a useful tool for checking link status and debugging link connections. To enable the use of CLI the OSD2892 must be connected to a PC with a USB port using a Mini-USB cable. Using a terminal emulation program such as Hyperterminal, a number of command... - Page 12 The configuration will be saved into Flash so that the desired configuration setup will be in effect at the next startup. PS: All configuration changes must be saved otherwise all the changes will be lost after rebooting! DOC ID: 10118602 PAGE 12 OSD2892 QUICK START GUIDE...
-
Page 13: Gui Overview
This Quick Start Guide will only show a few main or important features to get the user running the OSD2892 successfully. On the top right hand of the GUI screen there are a few icons available to quickly navigate or obtain help for each GUI menu items. -
Page 14: Ip Configuration
If multiple IP addresses are required, click Add Interface to add more IP interfaces. Click Save to save the configuration. Use new IP address to access the switch. PS: All configuration changes must be saved otherwise all the changes will be lost after rebooting! DOC ID: 10118602 PAGE 14 OSD2892 QUICK START GUIDE... -
Page 15: Users Authentication
Click admin to change the current admin account setting. If multiple users are required, click Add New User PS: All configuration changes must be saved otherwise all the changes will be lost after rebooting! DOC ID: 10118602 PAGE 15 OSD2892 QUICK START GUIDE... -
Page 16: Save Configuration To Start-Up
Save startup-config Click Save Configuration to save the configuration on start-up. PORT SPEED SETTING The port speed settings for the OSD2892 is auto mode for copper port and 10G for SFP port. On the tree map below expand Configuration Ports. -
Page 17: Warranty
For warranty period, please call your local OSD distributor. REPAIRS Optical Systems Design reserves the right to repair or replace faulty modules/units. Please obtain a “Return Material Authorisation” (RMA) form and number before returning goods. Goods must be returned in adequate packing material to Optical Systems Design, Warriewood or its nominated authorised representative, for all repairs. - Page 18 OPTICAL SYSTEMS DESIGN DOC ID: 10118602 PAGE 18 OSD2892 QUICK START GUIDE...
- Page 19 OPTICAL SYSTEMS DESIGN DOC ID: 10118602 PAGE 19 OSD2892 QUICK START GUIDE...
- Page 20 OPTIC L Optical Systems Design Pty. Ltd. 7/1 Vuko Pl. Warriewood 2102 SYSTEMS P.O. Box 891 Mona Vale N.S.W. Australia 2103 Telephone: +61 2 9913 8540 Facsimile: +61 2 9913 8735 DESIGN Email: sales@osd.com.au Web Site: www.osd.com.au PTY LTD A.B.N. 83 003 020 504...