Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Optical Systems Design OSD2144A SERIES
Summary of Contents for Optical Systems Design OSD2144A SERIES
- Page 1 OPERATOR MANUAL OSD2144A SERIES 5 PORT UNMANAGED GIGABIT ETHERNET SWITCH...
-
Page 3: Table Of Contents
OPTICAL SYSTEMS DESIGN INDEX 1 TECHNICAL SUMMARY ......................4 BRIEF DESCRIPTION ......................4 1.1.1 OVERVIEW ........................4 1.1.2 APPLICATIONS ......................4 1.1.3 FEATURES AND BENEFITS ..................4 TYPICAL CONFIGURATION ....................5 TECHNICAL SPECIFICATIONS ................... 6 OSD2144A FRONT AND REAR PANELS ................7 INSTALLATION AND OPERATION .................. -
Page 4: Technical Summary
OPTICAL SYSTEMS DESIGN 1 TECHNICAL SUMMARY BRIEF DESCRIPTION 1.1.1 OVERVIEW The OSD2144A is designed to convert between 10/100/1000Base-T copper cabling and 1000Base-Lx fiber cabling. It has two fixed 10/100/1000Base-T RJ45 copper ports, and three SFP ports which can be specified by the user for 10/100/1000Base-T, 100Base-Fx or 1000Base-X. The same unit will operate on either singlemode or multimode fiber. -
Page 5: Typical Configuration
OPTICAL SYSTEMS DESIGN TYPICAL CONFIGURATION Figure 1 below indicates possible set-ups for an OSD2144A system. Point-to-Point Configuration OSD2144A OSD2144A Network Switch Network Switch Bus Configuration IP Camera IP Camera IP Camera Network Switch FIGURE 1: OSD2144A TYPICAL RING CONFIGURATION DOC ID: 10109603... -
Page 6: Technical Specifications
OPTICAL SYSTEMS DESIGN TECHNICAL SPECIFICATIONS TABLE 1: TECHNICAL SPECIFICATIONS SPECIFICATION PERFORMANCE IEEE802.3i 10Base-T, IEEE802.3u 100Base-T, 8023ab 1000Base-T Electrical Data Interface Electrical Data Connector RJ45 for fixed copper (ports 1 and 2) and SFP modules for port 3,4,5 10, 100, 1000Mbps for copper... -
Page 7: Osd2144A Front And Rear Panels
OPTICAL SYSTEMS DESIGN OSD2144A FRONT AND REAR PANELS There are two fixed copper ports for 10/100/1000Base-T and three optional SFP ports which can be either copper or fiber on the front panel. The rear panel of the module version consists of a 6-way terminal block power connector while the card version consists of a DB9 power connector which is supplied by the OSD370 (or OSD350) chassis. -
Page 8: Installation And Operation
OPTICAL SYSTEMS DESIGN 2 INSTALLATION AND OPERATION INTRODUCTION This section outlines the methods required to install and operate the OSD2144A successfully. It should be studied carefully if damage to the equipment or poor results are to be avoided. This equipment has been fully tested prior to dispatch and is ready for immediate operation. However it is advisable to check for external transportation damage before operation. -
Page 9: Osd2144A Drawings And Dimensions
OPTICAL SYSTEMS DESIGN 2.2.2 OSD2144A DRAWINGS AND DIMENSIONS The OSD2144A standalone module is designed to be mounted on an even surface and to be secured by means of M4 or smaller screws. The OSD2144A card version is designed to be inserted into a chassis and secured by means of captivated screws. -
Page 10: Power Supply Connections
OPTICAL SYSTEMS DESIGN 2.2.3 POWER SUPPLY CONNECTIONS The OSD2144A card version is powered from the OSD370 or OSD350 chassis. DC power on the OSD2144A card version is connected via the DB9 connector. The card version of the OSD2144A should be fixed into the OSD370 (or OSD350) chassis using the captivated screws. The card can be plugged in or out of the OSD370 (or OSD350) chassis with power on or off. -
Page 11: Port Allocation And Led Indicators
OPTICAL SYSTEMS DESIGN 2.2.5 PORT ALLOCATION AND LED INDICATORS Port 5 Port 4 Port 3 Port 2 Port 1 Case 1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 5 5 5 5... -
Page 12: Controls
OPTICAL SYSTEMS DESIGN 2.2.6 CONTROLS The OSD2144A has a 4-way DIP switch to control a number of functions. Table 4 outlines the function of each switch. Note: The 8-way DIP switch is not used. 4-Way DIP Switch Not Used FIGURE 7: OSD2144A CONTROLS... -
Page 13: Fitting Sfp Connectors
OPTICAL SYSTEMS DESIGN 2.2.7 FITTING SFP CONNECTORS Care should be taken when inserting/removing the SFP connectors from SFP port 3,4 and 5 as SFP modules are Electrostatic (ES) sensitive and Electrostatic Discharge (ESD) precautions should be taken when installing. Ensure that the SFP is fully engaged and latched into position. -
Page 14: Osd2144A Operation
OPTICAL SYSTEMS DESIGN OSD2144A OPERATION When using the OSD2144A for the first time, check that the unit is in good condition with no visible damage. If a card version is used, insert it in an appropriate slot on the OSD370 or OSD350 chassis and check that the indicators illuminate accordingly on power up (see Table 3). -
Page 15: Maintenance
OPTICAL SYSTEMS DESIGN 3 MAINTENANCE INTRODUCTION The following section outlines the fault-finding procedure for the OSD2144A modems. Please take note of the following: Personnel without appropriate training should not attempt any maintenance except that outlined ▲ below. If further maintenance is attempted you are warned that every care should be taken to ensure that ▲... -
Page 16: Warranty
For warranty period, please contact your local OSD distributor. REPAIRS Optical Systems Design reserves the right to repair or replace faulty modules/units. Please obtain a “Return Material Authorisation” (RMA) form and number before returning goods. Goods must be returned in adequate packing material to Optical Systems Design, Warriewood or its nominated authorised representative, for all repairs. - Page 20 OPTIC L Optical Systems Design Pty. Ltd. 7/1 Vuko Pl. Warriewood 2102 SYSTEMS P.O. Box 891 Mona Vale N.S.W. Australia 2103 Telephone: +61 2 9913 8540 DESIGN Facsimile: +61 2 9913 8735 Email: sales@osd.com.au Web Site: www.osd.com.au PTY LTD A.B.N. 83 003 020 504...