Related Manuals for Optical Systems Design OSD2154P
Summary of Contents for Optical Systems Design OSD2154P
-
Page 1: Index
OPERATOR MANUAL OSD2154P MICRO 10/100/1000Base-T to 1000Base-X 3-PORT SWITCH WITH PoE++ SOURCE... -
Page 3: Table Of Contents
1.1.3 FEATURES AND BENEFITS ..................... 5 TYPICAL CONFIGURATION ....................6 PRODUCTS AND OPTIONS ....................6 TECHNICAL SPECIFICATIONS ................... 7 OSD2154P FRONT AND REAR PANELS ................8 INSTALLATION AND OPERATION ..................9 INTRODUCTION ........................9 INSTALLATION ........................9 2.2.1 WARNING AND PRECAUTIONS ..................9 2.2.2... - Page 4 TABLE 1: PRODUCTS AND OPTIONS ....................6 TABLE 2: TECHNICAL SPECIFICATIONS ..................7 TABLE 3: POWER CONNECTION ..................... 11 TABLE 4: LED FUNCTION ......................... 13 TABLE 5: OSD2154P 3-WAY DIP SWITCH SETTINGS ..............14 DOC ID: 10116503 PAGE 4 OSD2154P OPERATOR MANUAL...
-
Page 5: Technical Summary
The unit will operate on either singlemode or multimode fiber by use of the appropriate optical device. A major benefit of the OSD2154P is its reliable operation over the -20°C to +75°C temperature range which allows it to be used in environments such as roadside cabinets, mine sites and factories. -
Page 6: Typical Configuration
Figure 1 below indicates the typical set-up for an OSD2154P system. FIGURE 1: OSD2154P TYPICAL CONFIGURATIONS PRODUCTS AND OPTIONS There are various options available for the OSD2154P as identified in Table 1 below: TABLE 1: PRODUCTS AND OPTIONS ITEM DESCRIPTION... -
Page 7: Technical Specifications
(attached power device dependant) Power Requirements recommended for PoE+ or ≥55V for 60W PoE ≥52V 2 Way 3.5mm Terminal Block on the module Power Connector Dimensions (mm) 90W x 88D x 49H 0.3kg Weight 1022154P02 DOC ID: 10116503 PAGE 7 OSD2154P OPERATOR MANUAL... -
Page 8: Osd2154P Front And Rear Panels
OPTICAL SYSTEMS DESIGN OSD2154P FRONT AND REAR PANELS The front panel consists of one fixed copper port for 10/100/1000Base-T, one SFP port and a 2-way terminal block power connector while the rear panel has one fixed copper port for 10/100/1000Base-T, a 3-way DIP switch and a USB port. -
Page 9: Installation And Operation
2 INSTALLATION AND OPERATION INTRODUCTION This section outlines the methods required to install and operate the OSD2154P successfully. It should be studied carefully if damage to the equipment or poor results are to be avoided. This equipment has been fully tested prior to dispatch and is ready for immediate operation. However it is advisable to check for external transportation damage before operation. -
Page 10: Osd2154P Drawings And Dimensions
OSD2154P DRAWINGS AND DIMENSIONS The standard OSD2154P is designed to be mounted on an even surface and to be secured by means of M4 or smaller screws. All dimensions are in mm. The unit also can be mounted on a standard DIN rail with the OSD2154P DIN Rail bracket. -
Page 11: Power Supply Connections
OPTICAL SYSTEMS DESIGN 2.2.3 POWER SUPPLY CONNECTIONS The OSD2154P requires external DC power. The voltage range of the OSD2154P is +46V +57V @ 6W. ≥52V is recommended for PoE+ (30W) and ≥55V for PoE++ (60W) operation. Power is connected to the 2-way terminal block located on the front panel as indicated in Table 3. -
Page 12: Location
The OSD2154P complies with IEEE802.3af, IEEE802.3at and PoE++, and is capable of supplying up to 60W of PoE per RJ45 port. The OSD2154P supports Alternative A & B (pins 1/2, 3/6, 4/5, 7/8). For PoE++ the OSD2154P transmits power over all 8 pins. Bidirectional data as well as power terminate on all 8 pins. -
Page 13: Led Indicators
No Optical Link Speed 1Gbps Green Power On Green Power Off Notes: When PoE LED is on it indicates that the unit is supplying power to the PSE Activity indicates traffic for copper port DOC ID: 10116503 PAGE 13 OSD2154P OPERATOR MANUAL... -
Page 14: Controls
The OSD2154P has a 3-way DIP switch to control a number of functions. Figure 8 outlines the function of each switch. For correct operation, set the required switch settings before powering the unit. The OSD2154P also has a reset switch located on the rear panel. Press this button momentarily to reset the unit. -
Page 15: Fitting Sfp Connectors
Using the lever, gently pull the SFP out. Fiber SFP Inserting Removing FIGURE 9: FITTING/REMOVING SFP CONNECTORS 2.2.9 BASIC CONNECTIONS Figure 10 shows basic user connections to the OSD2154P. Chassis Ground LC Fiber cable Ethernet cable Ethernet cable Power FIGURE 10: BASIC CONNECTIONS... -
Page 16: Osd2154P Single/Dual Signature Pd Operation
OSD2154P SINGLE/DUAL SIGNATURE PD OPERATION The OSD2154P can optionally support single, dual or either single/dual signature PD. This must be specified at time of sale. By default, dual signature PD is available on the front panel if a single and dual signature unit (option SD) is ordered. -
Page 17: Maintenance
OPTICAL SYSTEMS DESIGN 3 MAINTENANCE INTRODUCTION The following section outlines the fault-finding procedure for the OSD2154P modems. Please take note of the following: ▲ Personnel without appropriate training should not attempt any maintenance except that outlined below. ▲ If further maintenance is attempted you are warned that every care should be taken to ensure that... -
Page 18: Warranty
For warranty period, please call your local OSD distributor. REPAIRS Optical Systems Design reserves the right to repair or replace faulty modules/units. Please obtain a “Return Material Authorisation” (RMA) form and number before returning goods. Goods must be returned in adequate packing material to Optical Systems Design, Warriewood or its nominated authorised representative, for all repairs. - Page 19 OPTICAL SYSTEMS DESIGN DOC ID: 10116503 PAGE 19 OSD2154P OPERATOR MANUAL...
- Page 20 OPTIC L Optical Systems Design Pty. Ltd. 7/1 Vuko Pl. Warriewood 2102 SYSTEMS P.O. Box 891 Mona Vale N.S.W. Australia 2103 Telephone: +61 2 9913 8540 DESIGN Facsimile: +61 2 9913 8735 Email: sales@osd.com.au Web Site: www.osd.com.au PTY LTD A.B.N. 83 003 020 504...