Advertisement
© BOSTITCH 2019
ADJUSTING THE MAGAZINE
(All models EXCEPT N80CB-1ML-E, N8090CB-1ML-E)
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
1. The magazine contains an adjustable nail platform
compliance for the products.
on which the nail coil rests. The nail platform can
be adjusted up and down to specific nail settings.
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
2. To change settings, pull up on the post and twist
to the correct step. (Fig. 5)
rien que les produits soient conformes aux normes CE.
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
TRIP OPERATION MODE
die CE-Richtlinien für Produkte.
THESE TOOLS ARE FITTED WITH 2 DIFFFERENT
ACTUATION MODES DEPENDING ON THE MODEL.
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
m WARNING! Always disconnect air supply before
zeggen dat de producten voldoen aan de CE-vereisten.
making adjustments as accidental actuation may
occur, possibly causing injury.
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
produkterne.
SEQUENTIAL ACTUATION MODE:
Models: N64084-2-E, N66C-2-E, N66FH-2-E, N75C-2-E,
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
N75CWW-2-M, N89C-2-E, N512C-2-E
yhdenmukaisuutta.
CONTACT ACTUATION MODE:
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα
Models: N58C-1-E, N64084-1-E, N64099-1-E,
αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
N80CB-1ML-E, N8090CB-1ML-E, N89C-1P-E, N400C-1-E,
N401C-1-E
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
conformità CE per i relativi prodotti.
SEQUENTIAL ACTUATION
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for
The sequential actuation requires the operator to
hold the tool against the work with the safety yoke
CE-merking for produktet.
depressed before pulling the trigger. In order to drive
additional fasteners, the trigger must be released and
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
the tool lifted away from the work, before repeating the
conformidade com a CE para os produtos.
above mentioned steps.
This makes accurate fastener placement easier,
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
for instance on framing, toe nailing and crating
conformidad con las normas CE de los productos.
applications. The sequential actuation allows exact
fastener location without the possibility of driving
a second fastener on recoil, as described under
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
Contact Trip (below). The sequential actuation tool
conformidad con las normas CE de los productos.
has a positive safety advantage because it will not
accidentally drive a fastener if the tool is contacted
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu
against the work - or anything else - while the operator
nie stanowią deklaracji zgodności CE prezentowanych produktów.
is holding the trigger pulled.
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu
nie stanowią deklaracji zgodności CE prezentowanych produktów.
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
výrobky.
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem
jelenti a termék CE-megfelelőségét.
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
conformitatea CE pentru produse.
CONTACT ACTUATION
THESE TOOLS ARE FITTED WITH CONTACT
ACTUATION.
m WARNING! Always disconnect air supply before
making adjustments as accidental actuation may
occur, possibly causing injury.
m WARNING! Tools marked with this
symbol have either contact actuation,
continuous contact actuation or selectable
actuation with contact actuation selected.
WHEN IN CONTACT ACTUATION MODE:
These tools are designed for use in
production applications such as pallets,
furniture, manufactured housing or
upholstery. DO NOT use for applications such as
closing boxes or crates and fitting transportation safety
systems on trailers and lorries. This tool shall only be
used in safe working places. Care must be taken to
prevent accidental actuation when changing from one
working position to another.
The common operating procedure on "Contact
actuation" tools is for the operator to actuate the
safety trip while keeping the trigger pulled, thus driving
a fastener each time the work is contacted. This will
allow rapid fastener placement on many jobs, such
as pallet assembly. All pneumatic tools are subject to
recoil when driving fasteners.
The tool may bounce, releasing the safety yoke and if
unintentionally allowed to re-contact the work surface
with the trigger still actuated (finger still holding the
trigger pulled) an unwanted second fastener will be
driven.
FASTENER DEPTH CONTROL ADJUSTMENT
N66C-2-E, N66FH-2-E, N75C-2-E, N75CWW-2-M ONLY
(Fig. 6)
The DIAL-A-DEPTH™ Fastener Control adjustment
feature provides close control of the fastener drive
depth; from flush with the work surface to shallow or
deep countersink.
First, set the air pressure for consistent drive in the
specific work, then use the DIAL-A-DEPTH™ Fastener
Control adjustment to give the desired depth of drive.
N58C-1-E, N64084-1-E, N64084-2-E, N64099-1-E,
N89C-1P-E, N89C-2-E, N400C-1-E, N401C-1-E,
N512C-2-E ONLY (Fig. 7)
The Fastener Depth Control Adjustment feature
provides control of the nail drive depth from flush with
or just above the work surface to shallow or deep
countersink.
GB
9
Advertisement
