Table of Contents
Advertisement
Contents
MG.03.H3.02 - VLT is a registered Danfoss trademark
......................................................................................................... 3
Safety regulations ..................................................................................................... 4
Warning against unintended start ............................................................................. 4
Introduction .............................................................................................................. 5
Integration of frequency converter and motor ........................................................... 6
Key diagram for FCM 300 Series .............................................................................. 6
Product range .......................................................................................................... 7
Ordering ................................................................................................................... 7
Ordering info for Frames and Flanges ....................................................................... 8
Ordering info for inverter box position and drain hole position ................................... 8
Ordering form ........................................................................................................... 9
......................................................................................................... 10
FCM 305-375 for 3 phases, 380-480 V .................................................................. 10
General technical data ............................................................................................ 10
Tightening Torques ................................................................................................. 14
Maximum Cable Cross Section .............................................................................. 14
.......................................................................................................... 14
Description of the motor ......................................................................................... 15
Handling the FC motor .......................................................................................... 16
Bearings ................................................................................................................. 16
Output shafts ......................................................................................................... 16
Dimensions ............................................................................................................ 17
Installation of the FC motor ..................................................................................... 20
Alignment ............................................................................................................... 20
Bolt torques ........................................................................................................... 21
......................................................................................................... 21
Forced ventilation (FV) units (Not yet available) ........................................................ 22
FCM 300 Thermal Protection .................................................................................. 22
Control panel (175NO131) ...................................................................................... 23
..................................................................................................... 23
....................................................................................................... 23
Display ................................................................................................................... 23
LEDs ...................................................................................................................... 24
Control keys ........................................................................................................... 24
Control key functions .............................................................................................. 24
Display read-out state ............................................................................................ 25
Display mode ......................................................................................................... 25
Display mode - selection of read-out state ............................................................. 26
Quick menu mode versus Menu mode ................................................................... 26
Quick Setup via Quick menu .................................................................................. 27
Parameter selection ................................................................................................ 27
Menu mode ............................................................................................................ 27
Parameter groups .................................................................................................. 27
Changing data ........................................................................................................ 28
Changing a text value ............................................................................................. 28
Infinitely variable change of numeric data value ....................................................... 28
Menu structure ....................................................................................................... 29
Service plug kit (175N2546) ................................................................................... 30
Plug kit (175N2545) ................................................................................................ 30
Remote mounting kit (175N0160) ........................................................................... 30
®
VLT
FCM Series
1
Advertisement
Table of Contents
Related Manuals for Danfoss VLT FCM Series
Summary of Contents for Danfoss VLT FCM Series
-
Page 1: Table Of Contents
Changing a text value ..................... 28 Infinitely variable change of numeric data value ............28 Menu structure ....................... 29 Service plug kit (175N2546) ................... 30 Plug kit (175N2545) ....................30 Remote mounting kit (175N0160) ................30 MG.03.H3.02 - VLT is a registered Danfoss trademark... - Page 2 The low-voltage directive (73/23/EEC) ..............91 The EMC directive(89/336/EEC) ................91 What is covered? ....................91 Danfoss FCM 300 Series motor and CE labelling ........... 92 Compliance with EMC directive 89/336/EEC ............92 EMC standards ...................... 92 Aggressive environments ..................93 List of warnings and alarms ..................
-
Page 3: Introduction
The symbols used are the following: This symbol indicates a general warning. NB!: This symbol indicates something to be noted by the reader. This symbol indicates a high-voltage warning. MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 4: Safety Regulations
1. The VLT DriveMotor (FC motor) must be disconnected from mains if repair work is to be carried out. Check that the mains supply has been disconnected and that the necessary time has passed (4 minutes). MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 5: Introduction
FCM 300 Series. Misc. Promotion users Design PROFIBUS- Quick Setup VLT Software Brochure Data sheet Guide Manual MG.03.FX.YY Dialog MB.03.CX.YY MD.03.AX.YY MG.03.BX.YY MG.03.EX.YY MG.50.EX.YY Articles version number MZ.03.AX.YY YY = language MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 6: Integration Of Frequency Converter And Motor
There is no need for special details on wiring to meet the EMC directive, since motor cables are not necessary. The only connections are mains and control connections. Control structures Key diagram for FCM 300 Series MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 7: Product Range
Take a copy of the ordering form, see section Ordering form. Fill in and post or fax your order to the nearest branch office of the Danfoss sales organisation. On the basis of your order, the FCM 300 Series motor is given a type code. -
Page 8: Ordering Info For Frames And Flanges
Inverter box position, always top mounted. D1: Drain holes opposite inverter side, both drive end and non drive end. D2/D3: Drain holes 90° to inverter, both drive end and non drive end. MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 9: Ordering Form
® FCM Series Ordering form MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 10: Installation
*) Not valid for RFI class 1B units Torque characteristics: - Starting torque/overload torque ....................160 % for 1 min - Continuous torque ..........................see above Control card, digital/pulse inputs: - Number of programmable digital inputs ......................4 MG.03.H3.02 - VLT is a registered Danfoss trademark... - Page 11 - Resolution on output frequency ........................0.1 % - System response time ........................Max. 40 msec. - Speed accuracy (open loop, CT mode, 4 P motor driven in speed range 150-1500 rPm) ....+/- 15 rpm MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 12 • If a mains phase is missing, the inverter will cut out when a load is placed on the motor. Terminal arrangement (for installation see quick setup, MG.03.AX.62) MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 13 LED 303-304: Communication N RS 485 to bus or PC For PROFIBUS versions please refer to the 5 V DC Supply for RS manual MG.90.AX.YY. 0 V DC 485 bus MG.03.H3.02 - VLT is a registered Danfoss trademark...
-
Page 14: Tightening Torques
Max size control cable: Max size serial communication cable: Earth Ground: Screw Sizes Cover (lid) screws: Earth Ground and Cable Clamp screws (FCM 305-340): Earth Ground and Cable Clamp screws (FCM 355-375): MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 15: Description Of The Motor
Flange ring Air blower Stator Endshield drive end Mounting screws for air blower hood Stator Air blower hood Endshield non drive end Connector block Gasket Screws for connector block Metric blind plugs MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 16: Handling The Fc Motor
) tensile steel. Drive end shafts are provided All motors are dynamically balanced, to ISO 8821with with a tapped hole to DIN 332 Form D and a key convention to IEC 60034-14. closed profile keyway as standard. MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 17: Dimensions
Frame size 80 A [mm] B [mm] C [mm] H [mm] K [mm] AA [mm] 33.5 33.5 AB [mm] BB [mm] L [mm] AC [mm] HD [mm] 228.5 228.5 FCL [mm] FCW [mm] 141 MG.03.H3.02 - VLT is a registered Danfoss trademark... - Page 18 DIN 332 Form DR Frame size 80 D [mm] E [mm] ED [mm] EB [mm] DH [mm] M6x16 M6x16 M8x19 M8x19 M10x22 M10x22 M10x22 M12x28 M12x28 F [mm] GA [mm] 21.5 21.5 MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 19 FT100 FT100 FT115 FT115 FT130 FT130 FT130 FT165 FT165 DIN Ref. C120 C120 C140 C140 C160 C160 C160 C200 C200 M [mm] N [mm] P [mm] S [mm] T [mm] LA [mm] MG.03.H3.02 - VLT is a registered Danfoss trademark...
-
Page 20: Installation Of The Fc Motor
All figures are based on Lna bearing life of 20,000 hours. Lna = adjusted L10 life rating taking account of:-Reliability -Material improvements -Lubrication conditions Max. permissible radial load at end of shaft (horizontal mounting). MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 21: Bolt Torques
Having dismantled the motor, maintenance can be carried out to remove all dirt. For this purpose, the use of an air line supplying dry compressed air under comparatively low pressure is best, as MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 22: Forced Ventilation (Fv) Units (Not Yet Available)
At warning level => Warning indication goes on (LED and status word) and the unit might trip if the temperature doesn’t sink back below warning level within 15 minutes. If the function TEMP.DEP.SW is MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 23: Control Panel (175No131)
2nd line 4th line is used in operating status for showing 3rd line 12345678901234567890 a status text or in data change mode for showing 12345678901234567890 4th line the value of the selected parameter. MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 24: Leds
LEDs are used for parameter Setup, including choice of display indication during normal operation. Keys for local control are found under the indicator LEDs. MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 25: Display Read-Out State
In normal operation, up to 4 different operating variables can be indicated continuously: 1,1 and 1,2 and 1,3 and 2, and in line 4 the present operating status or alarms and warnings that have arisen. MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 26: Display Mode - Selection Of Read-Out State
Operating variables 1,1 and 1,2 and 1,3 in the first operating variable 2 remains unchanged. line, and operating variable 2 in the second line are selected via parameter 009, 010, 011 and 012. MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 27: Quick Setup Via Quick Menu
1 - see table below. Parameter selection The selection of parameter is effected by means of the [+/-] keys. The following parameters are accessible: MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 28: Changing Data
[<>] keys. FREQUENCY 50.0 Hz SETUP 130 START FREQUENCY 09.0 HZ Then the chosen digit is changed infinitely variably by means of the [+/-] keys: MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 29: Menu Structure
50.0 HZ 001 LANGUAGE ENGLISH DATA CHANGE MODE DATA CHANGE MODE QUICK MENU 1 OF 13 FREQUENCY 50.0 HZ 50.0 HZ 001 LANGUAGE 001 LANGUAGE ENGLISH ENGLISH Choice of data value 175ZA446.11 MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 30: Service Plug Kit (175N2546)
To make a plugable connection between LCP 2 and FCM 300. Used together with cable for plug kit 175N0162. Colour of wire/ Terminal X100/ D-sub pin Remote mounting kit (175N0160) yellow green blue Connections MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 31: Potentiometer Option (177N0011)
Colour of wire Terminal on X101 White 2 (analog input) 8 (0 V) Black 7 (+10 V) MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 32: Local Operation Pad (Lop) (175N0128) Ip65
At power up the unit will always be in stop mode. Set reference will be stored during power down. If permanent start mode is desired, connect terminal 6 to terminal 4 and do not connect MG.03.H3.02 - VLT is a registered Danfoss trademark... - Page 33 ® FCM Series NB!: After fitting, cut off or isolate excess wire. MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 34 FC motor. 013 a choice of [1] or [3] has been made. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
-
Page 35: Programming
Stop mode and only between units with the same major database version (see par. 626 value major.minor) = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark... - Page 36 FC motor. See Serial communication. For display read-outs, press the [DISPLAY/STATUS] button, see also page 31. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 37 LCP digital control and open loop [2] functions as LCP control and open loop [1], the only difference being that = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 38 002 has been set for Remote control [0] or Local control [1]. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 39 Local reference (parameter 003) is reset. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 40 [3] or Variable torque high [4] if the load is square (centrifugal pumps, fans). = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 41 132) is to be active. 0.0 sec. = OFF = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 42 The DC braking will be active when below cut in frequency and stop is activated at the same = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 43 Set the desired frequency. time as variable torque (parameter 101). See below speed profile for brake function. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 44 Example: ATB STD-4-075 means ATB 4 pole 0.75 kW motor. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 45 Choose the desired range. Value: 0.0 HZ - f (PARAMETER 202) [0 -] 0.0 HZ = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 46 104). This presupposes that the current limit is not reached (to be set in parameter 221). = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 47 If Sum [0] is selected, one of the adjusted preset references (parameters 215-216) is added as a percentage of the maximum possible reference. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 48 2, 3, 4, or 5 - see the table below. Terminals 2/3/4/5 Preset reference Preset reference 1 Preset reference 2 = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 49 The bypass band is the bypass frequency +/- the reference preset as a percentage will be calculated half the set bandwidth. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 50 See P332, P333, P334 and P335 Description of choice, where the description of the digital input set up is given. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 51 Motor Running, the output frequency is higher than 0.1 Hz. A start command has been given. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 52 1. Scaling of the input signal is effected in parameters 338 and 339. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 53 2-5. The function options are shown in the table below. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 54 Should not be used with Process, closed loop mode. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 55 0.0 - 20.0 mA [0 - 200] the same time as reset. 0.0 mA = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 56 Value: 0.0 - 10.0 V0.0 - 10.0 V [0 - 100] 10.0 V [100] = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 57 221 has been exceeded. Thermal warning, above the temperature limit in the frequency converter. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 58 In parameter 403 Sleep mode timer, the Sleep mode is activated. In parameter 403 Sleep mode timer, a timer = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 59 Start function (parameter 445). motor. This extends the time during which the = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 60 Automatic reset x 9 (AUTOMATIC X 9) Automatic reset x 10 (AUTOMATIC X 10) [10] = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 61 (parameters 204 and 205). depending on the output frequency. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 62 [29] will be in the form of a percentage of the selected range. [30] = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 63 Use the overview below to determine which terminal is to Bus reference 68+69 be used and which parameters are to be programmed. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 64 A choice can be made between voltage, current and pulse feedback signals. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 65 (PROC. INTEGR. T.) Value: 0.01 - 9999 sec. (OFF) [1 - 999900] 9999 sec. [999900] = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 66 It is possible to set a limit for the differentiator gain. which is spinning freely because of a mains dropout. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 67 See drawing. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 68 (active signal = 1) either via a control word or via a digital input. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 69 Max. speed (MAX SPEED) via the serial communication port. Stop and trip (STOP AND TRIP) = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 70 008 This value is updated every 320 ms. Display scaling of output frequency. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 71 = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 72 The value stated gives, as a percentage, the sum of external references (sum of analogue/bus/pulse). This value is updated every 80 ms. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 73 FC motor. by the offset and gain adjustment of the AD-converter. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 74 AD-converter. This value is updated every 20 ms. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 75 FC motor. Read out as a figure code between 1 and 37. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 76 Array type parameter. This parameter makes it possible to see at what current or voltage a given trip occurred. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 77 The key data of the unit can be read out via the display or the serial communication port. = factory setting. () = display text [] = value for use in communication via serial communication port MG.03.H3.02 - VLT is a registered Danfoss trademark...
-
Page 78: Pc Software Tools
A master can send the same telegram at the same Each telegram begins with a startbyte (STX) = 02 Hex, time to all slaves connected to the bus. In such followed by a byte that gives the telegram length (LGE) MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 79: Databytes
"first byte" = 0 0 0 0 0 0 1 0 (02H) reply back to the master. = 0 0 0 0 0 0 1 0 Commands master → slave: Each additional, subsequent byte is gated by MG.03.H3.02 - VLT is a registered Danfoss trademark... - Page 80 Setup has been selected seen in the section on factory settings. Since a parameter value can only be transferred as an integer, Parameter number (PNU) a conversion factor must be used to transfer decimals. MG.03.H3.02 - VLT is a registered Danfoss trademark...
-
Page 81: Control Word According To Fieldbus Profile Standard
Setup 1 Setup 2 "1" means that the frequency converter is able to start, provided the other conditions for starting are No function Reversing fulfilled. Note: In parameter 502 the choice is made MG.03.H3.02 - VLT is a registered Danfoss trademark... - Page 82 MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 83 221 has been exceeded. Bit 05, ON3/OFF3: Bit 05 = "0" means that control word bit 02 = "1". Bit Bit 15, Thermal warning: 05 = "1" means that control word bit 02 = "0". MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 84 Bit 11, No function / relay 123, digital output terminal 9: Bit 03, Coasting/enable: Coasting. Bit 03 = "0" leads to a stop. Bit 03 = "1" means that the frequency converter is able to start, MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 85 This can be the case i.e. while the speed is ramped up/down during start/stop. Bit 08 = "1" means that the present motor speed equals the speed reference set. MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 86 16384 (4000 Hex) corresponds to 100%. (Negative figures are formed by means of 2’s complement.) The bus reference has the following format: Parameter 203 = "0" "ref -ref " 0-16384 (4000 Hex) ~ 0-100% ~ ref - ref MG.03.H3.02 - VLT is a registered Danfoss trademark...
-
Page 87: All About Fcm 300
Galvanic isolation Extreme running conditions The voltage in the intermediate circuit is increased when Motor-generated overvoltage the motor acts as a generator. This occurs in two cases: MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 88: Acoustic Noise
61 dB(A) Balance The FCM 300 is balanced to class R according to ISO8821 (reduced balance). For critical applications especially at high speed (>4000 RPM) special balance (class S) might be required. MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 89: Thermal Protection And Derating
PWM schemes, SFAVM and 60° AVM. Factory setting Factory setting of the switching frequency is is SFAVM. The PWM scheme can be changed in 4000 Hz. It can be changed between 2 and 14 kHz in parameter 411. MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 90: Vibration And Shock
(transformer, cables). Consequently, in plants with a rather high percentage of rectifier load, it is important to maintain harmonic currents at a low level to avoid overload of the transformer and high temperature in the cables. MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 91: Power Factor
EU directives. The CE label says nothing about the are CE labelled under the EMC directive. specifications or quality of the product. Frequency converters are regulated by three EU directives: MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 92: Danfoss Fcm 300 Series Motor And Ce Labelling
(ISM) radio-frequency equipment. appliance, system or installation rests with the installer. - EN 55022: Limits and methods of measuring As an aid to the installer, Danfoss has prepared EMC radio disturbance characteristics of information installation guidelines for the Power Drive System. -
Page 93: Aggressive Environments
If there are problems with low frequency interference of copper rails and cable ends on existing installations. (ground loops), screened cable used for Profibus, standard bus, control cables and signal interface can be left open at one end. MG.03.H3.02 - VLT is a registered Danfoss trademark... -
Page 94: List Of Warnings And Alarms
Control panel STOP can only be restarted by master. The address is not changed back to factory the Control Panel START button. setting with reset to factory setting function. MG.03.H3.02 - VLT is a registered Danfoss trademark... - Page 95 The inverter peak current limit (approx. 230% of FC motor. the rated current) has been exceeded. The FC motor will trip, while giving an alarm. ALARM 11 MG.03.H3.02 - VLT is a registered Danfoss trademark...
-
Page 96: Warning Word, Extended Status Word And Alarm Word
This warning is active if the output frequency has reached parameter 201 Output frequency low limit or parameter 202 Output frequency high limit. WARNING/ALARM 34 HPFB error (HPFB ALARM): The profibus communication is not working correctly. ALARM 35 MG.03.H3.02 - VLT is a registered Danfoss trademark... - Page 97 Earth fault 00000800 Overcurrent 00004000 Motor thermistor 00008000 Inverter overload 00010000 Undervoltage 00020000 Overvoltage 00040000 Phase loss 00080000 Live zero error 00100000 Overtemperature 02000000 HPFB error 08000000 Inrush fault 10000000 Internal error MG.03.H3.02 - VLT is a registered Danfoss trademark...
-
Page 98: List Of Parameters
Data type shows the type and length of the telegram. with a frequency converter. See Databytes in Serial Bus. Data type Description Integer 16 Integer 32 Unsigned 8 Unsigned 16 Unsigned 32 Text string MG.03.H3.02 - VLT is a registered Danfoss trademark... - Page 99 0.00 % Reference preset 5 -100.00 % - +100.00 % 0.00 % Reference preset 6 -100.00 % - +100.00 % 0.00 % Reference preset 7 -100.00 % - +100.00 % 0.00 % MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 100 Terminal 1, max. scaling 0.0 - 20.0 mA 20.0 mA Terminal 2, min. scaling 0.0 - 10.0 V 0.0 V Terminal 2, max. scaling 0.0 - 10.0 V 10.0 V Output functions No operation MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 101 Data type shows the type and length of the telegram. with a frequency converter. See Databytes in Serial Bus. Data type Description Integer 16 Integer 32 Unsigned 8 Unsigned 16 Unsigned 32 Text string MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 102 Data read-out: Control word, binary Data read-out: Warning word, 1 Data read-out: Warning word, 2 Data read-out: Terminal 1, analog input mA X 10 Data read-out: Terminal 2, analog input V X 10 MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 103 Data type shows the type and length of the telegram. with a frequency converter. See Databytes in Serial Bus. Data type Description Integer 16 Integer 32 Unsigned 8 Unsigned 16 Unsigned 32 Text string MG.03.H3.02 - VLT is a registered Danfoss trademark...
-
Page 104: Index
Derating for air pressure ............Fault log: Error code ........Derating for ambient temperature ............. Fault log: Time ........ Derating for high switching frequency ............. Fault log: Value ........Derating for running at low speed MG.03.H3.02 - VLT is a registered Danfoss trademark... - Page 105 Lowpass filter .............. Process bytes ..........Process PID anti windup ..........Process PID diff. gain limit ........Process PID differentiation time ............machinery directive ..........Process PID integral time ......... Mains supply interference/harmonics MG.03.H3.02 - VLT is a registered Danfoss trademark...
- Page 106 ............. Service plug kit ............Selection of Setup ............Selection of speed ..............Sleep mode ............Slip compensation ................Start ..............Start voltage ............Static overload ............Switching frequency ............Switching pattern MG.03.H3.02 - VLT is a registered Danfoss trademark...