Related Manuals for Taylor 430 Torque
Summary of Contents for Taylor 430 Torque
- Page 1 Model 430 Torque Shake/Slush Freezer Original Operating Instructions 051430- M 3/97 (Original Publication) (Updated 7/3/12)
- Page 2 Amps Part Number: E March, 1997 Taylor All rights reserved. 051430-M Taylor Company The word Taylor and the Crown design 750 N. Blackhawk Blvd. are registered trademarks in the United States Rockton, IL 61072 of America and certain other countries.
-
Page 3: Table Of Contents
............Table of Contents Model 430 Torque... - Page 4 E March, 1997 Taylor (Original Publication) (Updated July, 2012) All rights reserved. 051430-M Taylor Company The word Taylor and the Crown design 750 N. Blackhawk Blvd. are registered trademarks in the United States Rockton, IL 61072 of America and certain other countries.
-
Page 5: To The Installer
Taylor equipment. water jet or hose to rinse or clean the unit. Failure to follow this instruction may result in electrocution. Only authorized Taylor service personnel should perform installation and repairs on the equipment. Authorized service personnel should consult This unit must be installed on a level surface OSHA Standard 29CFRI910.147 or the... -
Page 6: Air Cooled Units
60245 IEC 57) installed with the proper cord anchorage to relieve conductors from strain, including twisting, at the terminals and FOLLOW YOUR LOCAL ELECTRICAL CODES! protect the insulation of the conductors from abrasion. 101012 To the Installer Model 430 Torque... -
Page 7: Beater Rotation
Taylor service technician. To correct rotation on a single--phase unit, change the Taylor reminds technicians to be cautious of leads inside the beater motor. (Follow the diagram government laws regarding refrigerant recovery, printed on motor.) recycling, and reclaiming systems. -
Page 8: To The Operator
Distributor, and the required service work is provided by an authorized Taylor service technician. Taylor It should also be noted that Taylor does not warrant the reserves the right to deny warranty claims on refrigerant used in its equipment. For example, if the... -
Page 9: Safety
We at Taylor Company are concerned about the safety of the operator when he or she comes in contact with the freezer and its parts. Taylor has gone to extreme efforts to design and manufacture built--in safety DO NOT operate the freezer unless it is features to protect both you and the service technician. - Page 10 This freezer must be placed on a level surface. Failure to comply may result in personal injury meter from the surface of the machine and at a height or equipment damage. of 1.6 meters from the floor. 090114 Safety Model 430 Torque...
-
Page 11: Operator Parts Identification
Panel--Side Left 049639 Tray--Drip 049319 Tube--Feed 13/32 Hole 025663--10 Pan--Drip 17--1/4” Long 027504 Cover A.--Black Insulated X49679--BLA Gasket--Base Pan 049420 Panel--Back 049325 Panel A.--Front X50678 Panel--Side Right 049640 Stud--Nose Cone 013496 Washer--Freezer Stud 049032 070104 Model 430 Torque Operator Parts Identification... - Page 12 Seal--Drive Shaft 032560 O--Ring -- .291 ID x .080 W 018550 O--Ring 7/8 OD x .139 W 025307 Torque Assembly X50382 Arm--Torque 025660 Bearing--Guide 014496 Nut--Stud 029880 Gasket--Door 5.109” ID x 5.630 014030 111018 Operator Parts Identification Model 430 Torque...
- Page 13 Item Description Part Number Item Description Part Number Brush--3” x 7” White 023316 Brush--Rear Bearing 013071 Brush--Double Ended 013072 Lubricant--Taylor 047518 Brush--Draw Valve 014753 Video--Training M430Torque 050987--V *Not Shown. Model 430 Torque Operator Parts Identification...
-
Page 14: Important: To The Operator
When the light is flashing, it indicates that the hopper is empty and the mix supply needs replenishing. To prevent damage to the unit, refrigeration discontinues automatically when the mix Figure 2 out indicator lights. Important: To the Operator Model 430 Torque... -
Page 15: Operating Procedures
17, “Disassembly”, and start there. Assembly Figure 5 Note: When lubricating parts, use an approved food grade lubricant (example: Taylor Lube). Step 1 Step 2 Lubricate both grooves on the drive shaft and slide the Install the beater assembly. First check the scraper o--ring in place. - Page 16 Insert the torque rotor end with the guide bearing into the pilot hole in the center of the drive shaft. The hole in the torque rotor shaft should be rotated to the 12 o’clock position. Figure 11 Operating Procedures Model 430 Torque...
- Page 17 This will lock the ice buster in place. Install the draw handle pin, and close the draw valve by moving the handle to the left. Figure 16 Figure 14 Model 430 Torque Operating Procedures...
-
Page 18: Sanitizing
Step 9 cylinder. Allow the solution to agitate for five minutes. Lay the air/mix feed tube (optional) in the bottom of the mix hopper. Figure 19 Figure 21 090114 Operating Procedures Model 430 Torque... -
Page 19: Priming
After making an adjustment, allow the refrigeration system to cycle 2 or 3 times to accurately evaluate the viscosity. Figure 23 Figure 25 Model 430 Torque Operating Procedures... -
Page 20: Closing Procedure
“OFF” position. Place the sanitized lid on the rerun container and place Repeat this procedure until the rinse water being it in the walk--in cooler. drawn from the freezing cylinder is clear. Operating Procedures Model 430 Torque... -
Page 21: Cleaning
Note: If the drip pan is filled with an excessive amount of mix, it is an indication the drive shaft seal should be Step 6 replaced or properly lubricated. Wipe clean all exterior surfaces of the freezer. 090114 Model 430 Torque Operating Procedures... - Page 22 Note: For machines equipped with an air filter, prime the machine with rerun. When using it will be necessary to vacuum clean the filters rerun, skim off the foam and discard, then mix on a monthly schedule. 071205 Important: Operator Checklist Model 430 Torque...
- Page 23 All parts should be thoroughly cleaned of dried power source to prevent possible electrical damage. mix or lubrication accumulations which attract mice and other vermin. Your local Taylor Distributor can perform this service for you. Model 430 Torque Important: Operator Checklist...
- Page 24 Improper mixing of product. b. Carefully follow directions -- -- -- for mixing product. c. The viscosity adjustment is c. Adjust the viscosity control. set incorrectly. d. The torque arm is not d. Install the torque arm. installed. Troubleshooting Guide Model 430 Torque...
- Page 25 Replace or install front bearing. missing. 7. Excessive leakage into a. Improper or inadequate a. Use correct lubricant (Taylor Lube) and follow rear drip pan. lubrication of drive shaft lubrication procedures. seal. b. Bad or missing seal on drive b.
- Page 26 White Bristle Brush --1--1/2” x 2” Inspect & Replace Maximum if Necessary White Bristle Brush -- 3” x 7” Inspect & Replace Maximum if Necessary Refer to the Parts List on the next page when ordering the above parts. Parts Replacement Schedule Model 430 Torque...
- Page 27 Section 10 Parts List + Available Separately 120703 Model 430 Torque Parts List...
- Page 28 + Available Separately Parts List Model 430 Torque...
- Page 29 + Available Separately Model 430 Torque Parts List...
- Page 30 + Available Separately Parts List Model 430 Torque...
- Page 31 + Available Separately Model 430 Torque Parts List...
- Page 32 + Available Separately Parts List Model 430 Torque...
- Page 33 + Available Separately Model 430 Torque Parts List...
- Page 34 + Available Separately Parts List Model 430 Torque...
- Page 35 + Available Separately Model 430 Torque Parts List...
- Page 36 Model 430 Torque 050367--12 7/3/12...
- Page 37 Model 430 Torque 050367-27 7/3/12...