H3C S9500 Series Command Manual
Ethernet interface, routing switches
Hide thumbs
Also See for S9500 Series:
- Command manual (1842 pages) ,
- Operation manual (1504 pages) ,
- Operating manual (76 pages)
Table of Contents
Advertisement
Quick Links
Command Manual - Ethernet Interface
H3C S9500 Series Routing Switches
Chapter 1 Ethernet Interface Configuration Commands........................................................... 1-1
1.1 Ethernet Interface Configuration Commands .................................................................... 1-1
1.1.1 broadcast-suppression............................................................................................ 1-1
1.1.2 debugging ethernet packet...................................................................................... 1-2
1.1.3 description ............................................................................................................... 1-3
1.1.4 display brief interface .............................................................................................. 1-3
1.1.5 display counters ...................................................................................................... 1-6
1.1.6 display counters rate ............................................................................................... 1-8
1.1.7 display interface .................................................................................................... 1-10
1.1.8 display port ............................................................................................................ 1-13
1.1.9 display port-group manual..................................................................................... 1-14
1.1.10 display transceiver alarm interface...................................................................... 1-15
1.1.11 display transceiver diagnosis interface ............................................................... 1-18
1.1.12 display transceiver interface................................................................................ 1-19
1.1.13 display transceiver manuinfo interface................................................................ 1-21
1.1.14 duplex.................................................................................................................. 1-22
1.1.15 flag sdh................................................................................................................ 1-23
1.1.16 flow-control .......................................................................................................... 1-24
1.1.17 flow-interval ......................................................................................................... 1-24
1.1.18 group-member..................................................................................................... 1-25
1.1.19 interface............................................................................................................... 1-26
1.1.20 jumboframe enable ............................................................................................. 1-27
1.1.21 link-delay ............................................................................................................. 1-28
1.1.22 loopback .............................................................................................................. 1-29
1.1.23 mdi....................................................................................................................... 1-30
1.1.24 multicast-suppression ......................................................................................... 1-30
1.1.25 port-group............................................................................................................ 1-32
1.1.26 port-mode ............................................................................................................ 1-33
1.1.27 reset counters interface....................................................................................... 1-33
1.1.28 shutdown ............................................................................................................. 1-34
1.1.29 source-mac-tail.................................................................................................... 1-35
1.1.30 speed................................................................................................................... 1-36
Table of Contents
i
Table of Contents
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for H3C S9500 Series
Summary of Contents for H3C S9500 Series
-
Page 1: Table Of Contents
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Table of Contents Table of Contents Chapter 1 Ethernet Interface Configuration Commands............1-1 1.1 Ethernet Interface Configuration Commands ..............1-1 1.1.1 broadcast-suppression.................... 1-1 1.1.2 debugging ethernet packet..................1-2 1.1.3 description ....................... 1-3 1.1.4 display brief interface .................... -
Page 2: Chapter 1 Ethernet Interface Configuration Commands
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands Chapter 1 Ethernet Interface Configuration Commands 1.1 Ethernet Interface Configuration Commands 1.1.1 broadcast-suppression Syntax broadcast-suppression { ratio | pps max-pps } undo broadcast-suppression View... -
Page 3: Debugging Ethernet Packet
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands The broadcast suppression setting you configured will overwrite the previous broadcast suppression setting, if any. With multicast suppression enabled, broadcast suppression is enabled automatically. However, with broadcast suppression enabled, multicast suppression can not be enabled. -
Page 4: Description
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands Use the undo debugging ethernet packet command to disable Ethernet packet debugging. By default, Ethernet packet debugging is disabled. Examples # Enable Ethernet packet debugging. - Page 5 Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands View Any view Default Level 1: Monitor level Parameters interface-type: Interface type. interface-number: Interface number. |: Uses a regular expression to filter output information.
- Page 6 Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands Character Meaning Notes on Use Hyphen, which is used to connect two numbers or characters. Note that the ”1-9” represent a range from 1 to 9 (“1”...
-
Page 7: Display Counters
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands Interface Link Speed Duplex Link-type PVID GE4/2/1 DOWN auto auto access 1000 GE4/2/2 DOWN auto auto access GE4/2/4 DOWN auto auto access GE4/3/1 DOWN... - Page 8 Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands View Any view Default Level 1: Monitor level Parameters inbound: Displays statistics on inbound packets. outbound: Displays statistics on outbound packets. interface-type: Interface type.
-
Page 9: Display Counters Rate
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands Table 1-4 Description on the fields of the display counters command Field Description Interface Abbreviated interface name Total number of the packets received/sent through the Total(pkts) interface. - Page 10 Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands If you provide the interface-type argument, this command displays the statistics on the rate of the packets passing through all the interfaces that are in up state and are of the specified type.
-
Page 11: Display Interface
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands Note: The display counters and display counters rate commands only count the statistics on the packets passing through RPR logical ports. 1.1.7 display interface... - Page 12 Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands Unknown-speed mode, unknown-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation Flow-control is not enabled The Maximum Frame Length is 1552...
- Page 13 Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands Table 1-6 Description on the fields of the display interface command Field Description Ten-GigabitEthernet5/1/2 Ethernet interface physical state current state IP Packet Frame Type...
-
Page 14: Display Port
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands 1.1.8 display port Syntax display port { hybrid | trunk } View Any view Default Level 1: Monitor level Parameters hybrid: Displays the existing Hybrid ports. -
Page 15: Display Port-Group Manual
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands 1.1.9 display port-group manual Syntax display port-group manual [ all | name port-group-name ] View Any view Default Level 1: Monitor level Parameters all: Specifies all the manual port groups. -
Page 16: Display Transceiver Alarm Interface
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands 1.1.10 display transceiver alarm interface Syntax display transceiver alarm interface [ interface-type interface-number ] View Any view Default Level 1: Monitor level Parameters interface-type interface-number: Interface type and number. - Page 17 Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands Alarm Type Number Voltage low Numeric — — Transceiver info I/O error — — Transceiver info checksum error Transceiver type and port — —...
- Page 18 Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands Alarm Type Number Transceiver type not supported by — — port hardware XENPAK modules Receive optical power fault PMA/PMD receiver local fault PCS receive local fault...
-
Page 19: Display Transceiver Diagnosis Interface
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands <H3C> display transceiver alarm interface GigabitEthernet 1/1/1 GigabitEthernet1/1/1 transceiver current alarm information: TX fault PCS receive local fault Laser temperature fault 1.1.11 display transceiver diagnosis interface... -
Page 20: Display Transceiver Interface
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands Table 1-9 Description on the fields of the display transceiver diagnosis interface command Field Description Temp.(°C) Digital diagnostic monitoring – temperature Digital diagnostic monitoring – voltage with a precision of 1... - Page 21 CX4 cable: CX4 Stack cable: STACK Digital Diagnostic The support for digital diagnostic monitoring, which Monitoring could be YES or NO. For latest H3C modules, the vendor name in the RFID of the module displays. Vendor Name other modules, Original Equipment Manufacturer name displays.
-
Page 22: Display Transceiver Manuinfo Interface
Serial number generated during module test. The Number information is stored in the RFID. Manufacturing Date H3C module test date. The information is stored in the RFID. The specified vendor name for the module. The information Vendor Name is stored in the RFID. -
Page 23: Duplex
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands 1.1.14 duplex Syntax duplex { auto | full | half } undo duplex View Ethernet interface view Default Level 2: System level Parameters auto: Specifies the auto-negotiation mode. -
Page 24: Flag Sdh
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands 1.1.15 flag sdh Syntax flag { j0 | j1 } sdh value undo flag { j0 | j1 } sdh View Ten-GigabitEthernet interface view... -
Page 25: Flow-Control
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands 1.1.16 flow-control Syntax flow-control undo flow-control View Ethernet interface view Default Level 2: System level Parameters None Description Use the flow-control command to enable flow control on an Ethernet interface. -
Page 26: Group-Member
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands Default Level 2: System level Parameters interval: Interval for generating interface statistics, in the range of 5 to 300 (in seconds) in steps of 5. -
Page 27: Interface
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands port group. By default, a manual port group contains no Ethernet interface. Examples # Add interfaces Ethernet1/1/1 and Ethernet1/1/5 to the manual port group named group1. -
Page 28: Jumboframe Enable
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands [Sysname] interface ethernet 1/1/1 [Sysname-Ethernet1/1/1] 1.1.20 jumboframe enable Syntax jumboframe enable [ jumboframe-value ] slot slot-id undo jumboframe enable slot slot-id View System view... -
Page 29: Link-Delay
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands Note: The jumboframe-value argument is in the range 1,552 to 10,236 for the boards LSB1XP4B, LSB1XP4CA, LSB1XP4DB, LSB1GV48DA, LSB2GV48DA, and LSB1GV48DB. By default, the boards LSB1VPNB0, LSB1NAMB0 and LSB1NATB0 allow jumbo frames with their size being 8,192 bytes. -
Page 30: Loopback
Use the undo loopback command to disable Ethernet interface loopback testing. By default, Ethernet interface loopback testing is disabled. Note: Currently, the S9500 series do not support external loopback testing. Loopback testing is required when you test certain functions, such as locating problems in an Ethernet. -
Page 31: Mdi
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands Examples # Enable internal loopback testing on Ethernet 1/1/1. <Sysname> system-view [Sysname] interface ethernet 1/1/1 [Sysname-Ethernet1/1/1] loopback internal 1.1.23 mdi Syntax mdi { across | auto | normal }... - Page 32 Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands undo multicast-suppression View Ethernet interface view, port group view Default Level 2: System level Parameters ratio: Specifies a percentage of the total interface bandwidth for multicasts on the interface, in the range 1 to 100.
-
Page 33: Port-Group
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands Examples # Set the multicast threshold to 20 for Ethernet 1/1/1. <Sysname> system-view [Sysname] interface ethernet 1/1/1 [Sysname-Ethernet1/1/1] multicast-suppression 20 # Set the multicast threshold to 20 for all the interfaces in port group 1. -
Page 34: Port-Mode
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands [Sysname] port-group manual group1 [Sysname-port-group-manual-group1] 1.1.26 port-mode Syntax port-mode { lan | wan } undo port-mode View Ten-GigabitEthernet interface view Default Level 2: System level Parameters lan: Specifies LAN mode. -
Page 35: Shutdown
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands View User view Default Level 2: System level Parameters interface-type: Interface type. interface-number: Interface number. Description Use the reset counters interface command to clear the statistics on specific interfaces. -
Page 36: Source-Mac-Tail
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands Description Use the shutdown command to shut down an Ethernet interface. Use the undo shutdown command to bring up an Ethernet interface. By default, an Ethernet interface is up. -
Page 37: Speed
Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands By default, the source MAC address for an interface is that of the corresponding VLAN interface. Note: Currently, this command is not supported by the following boards: LSB1GV48DA, LSB1GV48DB, LSB2GV48DA, LSB1GP48DB, LSB1XP4B, LSB1XP4CA, and LSB1XP4DB. - Page 38 Command Manual – Ethernet Interface H3C S9500 Series Routing Switches Chapter 1 Ethernet Interface Configuration Commands Description Use the speed command to set the operating rate for an Ethernet interface. Use the undo speed command to restore the default operating rate.
Need help?
Do you have a question about the S9500 Series and is the answer not in the manual?
Questions and answers