Led Indication; Input Status Indication Leds; Error Status Led; Reset Procedure - King gates ELEVO Instructions And Warnings For Installation And Use

8.

LED indication

S2 PHOTO
STOP
START
S1 EDGE
36
With the control unit powered up (if control unit protection is not
activated) the yellow "Set" led flashes briefly and, if everything is
correctly hooked up, the red "S1 Edge","Stop" and "S2 Photo"
LEDs turn on to indicate that the three safety contacts are closed
circuits.
The yellow "Set" LED is exclusively reserved for programming.
8.1 -

Input status indication LEDs

RED S1 EDGE LED:
- on in the fixed mode if the S1 Edge contact (terminals 9-10) is
closed
- off if the S1 Edge contact (terminals 9-10) is opened
RED START LED:
- on in fixed mode if the Start contact (terminals 7-8) is closed
- off if the Start contact (terminals 7-8) is opened
When START on the board is pressed or a control signal is sent
by wire and the red LED flashes three times without the system
executing the manoeuvre, then "wire inputs are in lock mode":
see par. 14.2 (advanced programming manual).
RED STOP LED:
- on in fixed mode if the Stop contact (terminals 6-8) is closed
- off if the Stop contact (terminals 6-8) is opened
RED S2 PHOTO LED:
- on in fixed mode if the S2 Photo contact (terminals 4-8) is closed
- off if the S2 Photo contact (terminals 4-8) is opened
YELLOW SET LED:
- is on in fixed mode or flashes when the control unit is in a
programming menu
- is off when the control unit is in out of a programming menu
RED RADIO LED:
- flashes when a command is received through King Gates transmitter
- is on in fixed mode when the control unit is in a radio programming
menu
- is off when the control unit is in standby mode
RED ERROR LED:
- see paragraph 8.2
RED START LED, RED RADIO LED AND YELLOW SET LED:
- If, when attempting to enter any programming scheme, the "Set",
"Radio" and "Error" LEDs flash fast three times, it means that
the "control unit protection" is activated. See Paragraph 14.1 for
solving the problem.
8.2 -

Error status LED

SET
RED "ERROR" LED:
The red "error" LED has two functions:
RADIO
- During automation's movement, the LED flashes when a
mechanical stress point is detected (this corresponds to
increased motor effort). Adjust FORCE and OBS knobs
(slightly turn them clockwise) to solve this and check gate
STOP
mechanics if necessary. Attention: a minimum flash of
this LED during the door movement can be considered as
normal.
- In standby mode, the LEDs shows the current error type with a
series of regular flashes according to the following scheme:
Number of
flashes per
series
1
2
3
4
5
6
7
8
9.

RESET procedure

Reset procedure deletes door travel parameters (par. 6) and
all advanced functions (par. 11). It can be performed in case of
programming mistakes and it brings the STAR EVO control board to
factory settings.
This reset doesn't affect memorized radio transmitters (see par. 5
for radio trasmitters management).
STEP ACTION
PRESS THE
1
BUTTON FOR 8 SECOND
RELEASE START
2
BUTTON
PRESS THE
3
BUTTON FOR 3 SECOND
RESET IS NOW
4
COMPLETED
A NEW PROGRAMMING
OF THE AUTOMATION'S
5
MOVEMENTS IS
REQUIRED
SET
RADIO
STOP
Error description
On-board memory fault.
Photo-test of safety devices failed. See
Paragraph 4.1 for solving the problem.
Automation's movement programming
required. See Paragraph 6.
Input "S1 Edge" set as a resistive edge and
check failed. See Paragraph 13.4 for solving
the problem.
Power limit threshold
Obstacle detection due to encoder
Obstacle detection due to current
Motor not connected
RESULT
START
All LED flash
All LED continue to flash
START
All LED light up in series
The red "ERROR" LED
lights flashes 3 times
continuosly
17