Related Manuals for King gates Jet Series
Summary of Contents for King gates Jet Series
- Page 1 Gear motor for swing gates MADE IN ITALY INSTRUCTION MANUAL info@stedaparts.nl www.stedaparts.nl...
-
Page 2: General Description
1 - GENERAL DESCRIPTION 1A - WARNINGS Unfulfilment of the below listed instructions will release the KING gates srl, from any responsibility for damage caused to people or things. -Do not modify the product in any part. -To optimize the functioning of the automation use KING gates accessories only. -
Page 3: Typical System
2 - TYPICAL SYSTEM 2A - TYPICAL SYSTEM A - Gear-motor B - Control unit C - Flashing-light with antenna D - Photocells (while closing) E - Photocells (while opening) F - Key selector G - Warning sign H - Stop locks 2B - TYPICAL CONNECTION AND CABLE SECTION RG58 (dist max 5m) 0,5mm2 (dist max 50m) - Page 4 2C - DIMENSIONS Front Rear braket braket 130mm 130mm 40mm 60mm Rear vertical 60mm braket 130mm info@stedaparts.nl www.stedaparts.nl...
- Page 5 3 - BRACKETS INSTALLATION SCHEME 3A - HOW TO USE THE SCHEME Measure "E" and draw a horizontal line in the scheme (pic.3.3 or 3.4 or 3.5 or 3.6) at the corresponding value. Choose a point on the drawn line, considering the desired opening angle. Draw a vertical line from that point and determinate the A value.
- Page 6 3B - INSTALLATION SCHEME: MECHANICAL LIMIT SWITCH IN OPENING MECHANICAL LIMIT SWITCH IN OPENING 90° 100° 110° A (mm) Pic. 3.3 info@stedaparts.nl www.stedaparts.nl...
- Page 7 3C - INSTALLATION SCHEME: MECHANICAL LIMIT SWITCH IN CLOSING MECHANICAL LIMIT SWITCH IN CLOSING 90° 100° 110° A (mm) Pic. 3.4 info@stedaparts.nl www.stedaparts.nl...
- Page 8 3D - INSTALLATION SCHEME: MECHANICAL STOPS (IN OPENING AND CLOSING, JET TOP VERSION) OPENING CLOSING MECHANICAL MECHANICAL STOP STOP 90° 100° A (mm) Pic. 3.5 info@stedaparts.nl www.stedaparts.nl...
- Page 9 3E - INSTALLATION SCHEME: NO MECHANICAL STOPS NO MECHANICAL STOPS 90° 100° 110° A (mm) Pic. 3.4 info@stedaparts.nl www.stedaparts.nl...
-
Page 10: Installation
4 - INSTALLATION 4A - INTRODUCTION Read the instructions with care before installing the product. The producer disclaims all responsibility for any damage or bad functioning caused by inobservance of the instructions or bad connection that may result in poor safety and functioning of the gear-motor. -
Page 11: Manual Override
5 - MANUAL OVERRIDE 5A - INTRODUCTION Before operating the manual override disconnect the power Manual override has been thought for manual opening of the gate in case of power-cut or motor breakdown. 5B - OVERRIDE INSTRUCTION (see pic.4). - Operate the manual override by moving back the key hole cover. - Insert the key in the cylinder lock and turn it of 90°... -
Page 12: Electrical Connection
6 - ELECTRICAL CONNECTION 6A - CONNECTION TO THE POWER STATION The installer is provided with the assembled connector. This has the function of connecting the motor to the power station and to power it. This procedure can only be carried out by authorized staff. Dismantle the connector by unscrewing screw “A”... -
Page 13: Stop Adjustment
7 - STOP ADJUSTMENT 7A - INTRODUCTION The mechanical-stop enables to stop the gate at a required position, avoiding the door to hit the stop devices. 7B - INSTRUCTION FOR THE REGOLATION INSTRUCTION (see pic.7): - Set the gear-motor on manual override (pic.4). - Twist off the screw of the mechanical-stop (B or D). -
Page 14: Compatibilità Elettromagnetica
DICHIARAZIONE CE DI CONFORMITÀ DECLARATION OF CONFORMITY Il sottoscritto Alex Antoniolli, legale rappresentante della ditta King gates srl, dichiara che il prodotto: The undersigned Alex Antoniolli, general manager of the following producer, declares that the product: NOME PRODUTTORE: King gates srl Manufacturer’s name:...