YASKAWA D1000 Series Quick Start Manual page 27

Control Circuit Terminal Functions
Type No.
S1
S2
S3
S4
S5
S6
Multi-Function
S7
Digital Inputs
S8
SC
SP
SN
+V
-V
A1
A2
Analog Inputs
A3
AC
E(G)
Type No.
MA
Fault Relay
MB
Output
MC
M1
M2
Multi-Function
M3
Digital
Output M4
<1>
M5
M6
FM
Monitor Output
AM
AC
<1> Refrain from assigning functions to digital relay outputs that involve frequent switching, as doing so may shorten relay performance life.
Switching life is estimated at 200,000 times (assumes 1 A, resistive load).
YASKAWA ELECTRIC TOEP C710656 06A YASKAWA Power Regenerative Converter - D1000 Quick Start Guide
Table 13 Control Circuit Input Terminals
Terminal Name (Function)
Multi-function input 1 (RUN-SB)
Multi-function input 2 (STOP)
Multi-function input 3 (External fault)
Multi-function input 4 (Fault reset)
Multi-function input 5 (Reserved)
Multi-function input 6 (Reserved)
Multi-function input 7 (Reserved)
Multi-function input 8 (External Baseblock)
Multi-function input common
Digital input power supply +24 Vdc
Digital input power supply 0 V
Analog reference input
Analog reference input
Multi-function analog input 1 (Reserved)
Multi-function analog input 2 (Reserved)
Multi-function analog input 3 (Reserved)
Frequency reference common
Ground for shielded lines and option cards
Table 14 Control Circuit Output Terminals
Terminal Name (Function)
N.O. output (Fault)
N.C. output (Fault)
Fault output common
Multi-function digital output (During Run 1)
Multi-function digital output (During MC on)
Multi-function digital output (Converter Ready)
Analog monitor output 1 (Power Supply Side
Power)
Analog monitor output 2 (Power Supply Side
Current)
Monitor common
4 Electrical Installation
Function (Signal Level) Default Setting
• Photocoupler
• 24 Vdc, 8 mA
• Set the S3 jumper to select between sinking, sourcing mode,
and the power supply.
24 Vdc power supply for digital inputs, 150 mA max (only
when not using digital input option DI-A3)
NOTICE: Do not jumper or short terminals SP and SN.
Failure to comply will damage the converter.
10.5 Vdc (max allowable current 20 mA)
-10.5 Vdc (max allowable current 20 mA)
-10 to 10 Vdc, 0 to 10 Vdc (input impedance: 20 kΩ)
• -10 to 10 Vdc, 0 to 10 Vdc (input impedance: 20 kΩ)
• 4 to 20 mA, 0 to 20 mA (input impedance: 250 Ω)
• Voltage or current input must be selected by DIP switch S1
and H3-09.
• -10 to 10 Vdc, 0 to 10 Vdc (input impedance: 20 kΩ)
• Use DIP switch S4 on the terminal board to select between
analog and PTC input.
0 V
Function (Signal Level) Default Setting
30 Vdc, 10 mA to 1 A; 250 Vac, 10 mA to 1 A
Minimum load: 5 Vdc, 10 mA
30 Vdc, 10 mA to 1 A; 250 Vac,
10 mA to 1 A
Minimum load: 5 Vdc, 10 mA
30 Vdc, 10 mA to 1 A; 250 Vac,
10 mA to 1 A
Minimum load: 5 Vdc, 10 mA
-10 to +10 Vdc, or 0 to +10 Vdc
0 V
–
27