Technical Specifications; Technical Data; Routine Maintenance - FAAC S800 ENC Instruction Manual

3.6 TECHNICAL SPECIFICATIONS

The hydraulic actuator S800 ENC is available in different versions
for 100° or 180° leaf opening options and for the CBAC or SBW type of
motor block.
- CBAC (With Opening and Closing Block): when the motor is not
running, resistance to movement is high. The hydraulic RE-
LEASE device is required for manual operation. Electric locks
are not required to hold the opening/closing positions.
- SBW (Without Windy Block) suitable for windy areas: when the
motor is not running, resistance to movement is low (the limits of
use in relation to the wind are described in detail in  1 ). The
Hydraulic Release device is recommended for manual opera-
tion. Electric locks are required to hold the opening/closing
positions.
Control system
- S800 ENC must be connected to a FAAC electronic board for the
control of 230 V for swing gates, fitted with a BUS connection
and slowdown control at the limit switch.
Standard equipment (on all versions)
- BUS magnetic absolute encoder to detect slowdown and stroke
end positions and to recognise obstacles to movement (anti-
crushing electronic function).
- By-pass screws to adjust the maximum crushing force during
opening and closing.
- Service release lever: for manual operation during installation/
maintenance.
- Integrated mechanical opening and closing stops (positive stop):
used to define the leaf stop points. No external mechanical
stops are required when using the positive stops. Using positive
stops will also reduce the maximum stroke (maximum reduc-
tion: 30° for opening and 30° for closing). The limits of use of the
positive stops in relation to the length and weight of the leaf are
described in detail in  2.
 5 Technical data
Model
Version
Mains power supply voltage
Electrical motor
Thrust capacitor
Thermal protection
Max power
Max torque
Max. leaf width
Max. leaf weight
Max angular speed
Max leaf opening angle
Operating ambient temperature
Type of use
Continuous operating time (ROT)
Protection rating
Type of oil
Dimensions (W x D x H)
(Foundation box)
Weight
(Foundation box)
S800 ENC
S800 ENC S800 ENC
100° CBAC 230V 180° CBAC 230V
230 V~ 50 Hz 230 V~ 50 Hz
Asynchronous single-phase Asynchronous single-phase
8 μF 8 μF
120 °C 120 °C
280 W 280 W
550 Nm 550 Nm
2 m 2 m
800 kg 800 kg
7.8 °/s 7.8 °/s
113 ° 187 °
-20 °C +55 °C -20 °C +55 °C
Residential-Condominium Residential-Condominium
133' at 23 °C 133' at 23 °C
IP67 IP67
FAAC HP OIL FAAC HP OIL
380 x 220 x 160 mm 450 x 220 x 160 mm
(507 x 283 x 200 mm) (507 x 283 x 200 mm)
16 kg 16.5 kg
(18.3 kg) (18.3 kg)
FAAC Components required for installation:
- foundation box
- grooved joint kit
Optional FAAC accessories:
- hydraulic release device with coded key accessible from inside as
well as outside the gate (required on CBAC versions)
- lock with customised key for hydraulic release
S800 ENC
100° SBW 230V
230 V~ 50 Hz
Asynchronous single-phase
8 μF
120 °C
280 W
550 Nm
4 m
800 kg
7.8 °/s
113 °
-20 °C +55 °C
Residential-Condominium
133' at 23 °C
IP67
FAAC HP OIL
380 x 220 x 160 mm
(507 x 283 x 200 mm)
16 kg
(18.3 kg)
6
S800 ENC
180° SBW 230V
230 V~ 50 Hz
Asynchronous single-phase
8 μF
120 °C
280 W
550 Nm
4 m
800 kg
7.8 °/s
187 °
-20 °C +55 °C
Residential-Condominium
133' at 23 °C
IP67
FAAC HP OIL
450 x 220 x 160 mm
(507 x 283 x 200 mm)
16.5 kg
(18.3 kg)
532116 - Rev.A