Advertisement
Advertisement
Table of Contents
Related Manuals for FAAC D064
Summary of Contents for FAAC D064
- Page 1 D064...
-
Page 2: Preliminary Checks
AUTOMATED SYSTEM D064 These instructions apply to model FAAC D064. - Check correct balance and if the opening mechanical stops The D064 automated systems make it possible to automate have been installed. balanced sectional doors of single garages for residential - Remove the door’s existing closing mechanism to ensure the... -
Page 3: Ancillary Electrical Equipment
3 ANCILLARY ELECTRICAL EQUIPMENT Prepare the electric system in keeping with the instructions in the chapter entitled “Warnings for the installer”. When you have finished installing, check if any external pipes or cables can come into contact with moving parts. Install the fixed control points at a minimum height of 150 cm, clear of the door movement area, but in a position enabling visual control of that area. - Page 4 ONLY FOR EXTERNAL MECHANICAL RELEASE...
- Page 5 15°/20° OPTIONAL ONLY FOR EXTERNAL MECHANICAL RELEASE...
- Page 6 4 E064 CONTROL BOARD 4.1 Technical specifications 230 / 50 Supply voltage (V ~ / Hz.) Power supply to accessories (Vdc) Accessories max. load (mA.) -20 / +55 Operating ambient temperature (°C) for receiver boards XF433 / Quick-fit connector XF868 and battery module Automatic / Semiautomatic Operating logics Open/Stop/Safety devices/Fail-...
- Page 7 - The D064 operator has a cable with a two-pole plug for 230 and goes into closed status. To restore the correct Vac power supply.
- Page 8 The learning cycle makes it possible to define the following: 7 PROGRAMMING 7.1 Setting the board - the force required to move the door. - the slow-down points. Set the unit with Dip-Switch DS1 to obtain the operation you - the opening and closing stop points. require.
-
Page 9: Memory Storage Of Radio Controls Coding
During these 5 seconds, in order to lighten the load on the 1) Give the 1st OPEN command: the operator performs a release system, you can send OPEN pulses within a time interval deceleration closing manoeuvre until it detects the stop of 2 seconds from each other, in order to reverse the carriage. - Page 10 1) Obtain a radio control already stored on one of the 2 channels (OPEN A or OPEN B). 2) Press and simultaneously hold down push-buttons P1 and P2 until the lights of both the LEDs on the board light up. 3) Both LEDs flash slowly for 5 sec.
-
Page 11: Maintenance
Once a month: check the efficiency of the anti-crushing device and also check if it is able to detect a 50mm high obstacle laid on the ground. 12 REPAIRS For repairs, contact FAAC’s authorised Repair Centres. Fig. 12 13 TROUBLESHOOTING Trouble... -
Page 12: Warnings For The Installer
17) FAAC declines all liability as concerns safety and efficient operation of a source of danger. the automated system, if system components not produced by FAAC 6) FAAC declines all liability caused by improper use or use other than are used. that for which the automated system was intended.
Need help?
Do you have a question about the D064 and is the answer not in the manual?
Questions and answers
Se me queda una rajita abierta como puedo bajar un poco la puerta
To lower the door on a FAAC D064 to close a small gap, follow these steps:
1. Check the Balance – Ensure the door is correctly balanced and the mechanical stops are properly installed.
2. Adjust the Settings – Use the control unit to fine-tune the door’s closing position.
3. Verify Clearance – Ensure there is at least 35 mm between the ceiling and the highest sliding point of the door.
4. Manual Release – If necessary, use the manual release mechanism to adjust the door manually.
If the gap persists, consider adjusting the anti-crushing sensitivity or checking for obstructions affecting the door’s movement.
This answer is automatically generated