S800 Enc; Intended Use; Limits Of Use; Unauthorised Use - FAAC S800 ENC Instruction Manual

3. S800 ENC

3.1 INTENDED USE

Underground actuators of the FAAC S800 ENC series are designed
to activate horizontally moving swing gates for residential/condo-
minium use.
One underground actuator must be installed for each leaf.
The systems set up with S800 ENC must only be intended for vehicle
transit.
See the instructions in § 8.3 to move the gate by hand.
!
Any other use, not specifically described, is prohibited and might affect
the integrity of the product and/or be a source of danger.

3.2 LIMITS OF USE

The leaf must comply with the dimensional and weight limits speci-
fied in the technical data.
Comply with the frequency of use limits indicated in the technical
data.
Environmental phenomena, even occasional, such as ice, snow and
strong wind may hinder correct operation of the automation and
affect component integrity and may become a potential source of
danger (see § Use in an emergency).
The limits of use in relation to the wind are described in detail in
 Limits of use of S800 ENC in relation to the wind.
In the presence of a pedestrian door integrated in the leaf of the gate,
motorised movement must be prevented when the pedestrian door
is not closed.
S800 ENC is not designed as a protective system against intrusion.
S800 ENC must be connected to an electronic board FAAC for 230 V
motor control of swing gates, fitted with a BUS connection and slow-
down control at the limit switch.
The automation set-up requires necessary safety devices to be in-
stalled, which are identified by the installer after having carried out
a proper risk assessment of the installation site.

3.3 UNAUTHORISED USE

- Any use other than the intended use is prohibited.
- It is prohibited to install the automation outside of the limits set
forth in the Technical data and the Installation requirements.
- It is prohibited to install the automation along escape routes.
- It is prohibited to install the automation to implement smoke
and/or fire protection doors (fire doors).
- It is prohibited to install the automation in areas that are at risk of
explosion and/or fire: the presence of flammable gases or fumes
poses a severe danger for safety (the product is not certified
pursuant to directive 94/9/EC ATEX).
- It is prohibited to power the system with energy sources other
than those set forth.
- It is prohibited to integrate unrelated commercial systems and/
or equipment, or employ them for uses that are not allowed by
the respective manufacturers.
- It is prohibited to use and/or install accessories that are not
specifically approved by FAAC S.p.A..
- It is prohibited to use the automation before having commis-
sioned the system.
- It is prohibited to use the automation with faults/tampering
which could jeopardise safety.
- It is prohibited to use the automation with movable and/or fixed
guards that have been tampered with or removed.
- Do not expose the actuator to direct jets of water of any type
and amount.
- Do not expose the actuator to chemical or aggressive environ-
mental agents.
S800 ENC
- Do not use the automation when its range of action is not clear
of people, animals or objects.
- Do not pass and/or stop within the automation's range of action
while it is moving.
- Do not obstruct the movement of the automation.
- Do not climb onto, hold onto or be pulled by the leaf.
- Do not allow children to come close or play near the automation's
range of action.
- Do not allow the control devices to be used by persons who are
not specifically authorised and trained.
- Do not allow the control devices to be used by children or persons
with reduced mental-physical abilities, unless under the supervi-
sion of an adult responsible for their safety.
!
When moving it manually, slowly guide the leaf for its entire stroke,
do not push the leaf so it moves freely.

3.4 USE IN AN EMERGENCY

In any malfunction, emergency or fault, disconnect the power sup-
ply of the automation. If the conditions allow the leaf to be safely
moved manually, use the MANUAL OPERATION; otherwise, keep the
automation out of service until it is restored/repaired.
In case of a fault, the automation must be restored/repaired must
only be carried out by the INSTALLER/MAINTENANCE TECHNICIAN.

3.5 PRODUCT IDENTIFICATION

The product is identified by the plate (see 2).
FAAC S.p.A. Soc. Unipersonale
Via Calari, 10 - 40069 Zola Predosa BOLOGNA
Italy
S800 ENC
5
Sales code
Product name
IDENTIFICATION NUMBER
Month/Year of manufacture + Progressive
number in production month.
Example: 0115 0001
made in January 2015 S/N 1
2
532116 - Rev.A