Page 2
Nessuna parte di questo manuale può essere riprodotta, archiviata, distribuita a terzi né altrimenti copiata, in qualsiasi formato e con qualsiasi mezzo, sia esso elettronico, meccanico o tramite fotocopia, senza il preventivo consenso scritto di FAAC S.p.A. Tutti i nomi e i marchi citati sono di proprietà dei rispettivi fabbricanti.
It is specifically understood that FAAC S.p.A. does not accept any liability with regard to the reli- ability and/or completeness of the above instructions. Therefore, the...
The installer must prove or declare to possess technical and profes- anti-slip devices at the top and bottom, equipped with retainer hooks. sional proficiency to perform installation, testing and maintenance activities according to the requirements in these instructions. S800 ENC 532116 - Rev.A...
STORAGE Store the product in its original packaging, in closed and dry premises, 1 S800 ENC protected from the sun and free from dust and aggressive substances. 2 Installation support Protect from mechanical stress. If stored for more than 3 months, regularly check the condition of the components and the packaging.
One underground actuator must be installed for each leaf. - Do not climb onto, hold onto or be pulled by the leaf. The systems set up with S800 ENC must only be intended for vehicle - Do not allow children to come close or play near the automation's transit.
Electric locks are required to hold the opening/closing positions. Control system - S800 ENC must be connected to a FAAC electronic board for the control of 230 V for swing gates, fitted with a BUS connection and slowdown control at the limit switch.
Alternatively, eliminate or adequately protect the sharp edges and protruding parts. Installing S800 ENC only requires the presence of the upper hinge of the leaf since the lower rotation fulcrum is provided by the foundation box. If an existing gate is automated, it must be dismantled and the lower hinge removed before installing the actuator.
Anchor the leaf to the lifting device with a rope or a suitable chain. After removing the leaf, place it on the ground or anchor it with a rope or chain to prevent it from tipping over. Ø MAX 35 mm Ø MAX 50 mm 7 S800 ENC 532116 - Rev.A...
The guide bracket is an important component for installation safety, to guarantee the stability and control of the leaf during movement. The guide bracket in the FAAC catalogue is designed for applications with leaves up to the maximum weight and length indicated in the Technical data.
3. Restore the actuator by turning the service lever clockwise until 100 Nm it stops ( 1 6 -3). 15 Left leaf Right leaf Restore actuator: turn completely closing opening left leaf 16 right leaf S800 ENC 532116 - Rev.A...
2. Ensure that the maximum manual moving force of the leaf is less than 220 N. 3. Use appropriate signs to highlight the areas where residual risks remain despite having implemented all safety measures. 18 4. Put up the ''DANGER: AUTOMATIC MOVEMENT'' sign on the gate S800 ENC 532116 - Rev.A...
Do not modify the original components in any way. the screw (1 9-2A or B): oil emulsified with air leaks out. FAAC S.p.A. disclaims any liability for damage caused by components 5. Tighten the screw before the leaf completes the stroke.
Page 18
Check the welding of the joint on the guide bracket. Check reversibility and irreversibility. Check that there is no oil leakage. Top up the oil level, if necessary. Only use FAAC oil. Bleed the oil, if necessary. Clean the actuator and the foundation box Check drainage efficiency.
8.1 SAFETY RECOMMENDATIONS RELEASE MANOEUVRE Systems set up with FAAC S800 ENC series underground actuators are 1. Open the cap of the lock (20 -1). intended for vehicle transit. 2. Insert the key and turn it one anti-clockwise turn until it stops The user must be in good physical and mental condition, aware of (...
1 The limits of use of S800 ENC in relation to the wind The table shows the maximum wind allowed for S800 ENC based on the leaf surface exposed to the wind. Winds that exceed those allowed may affect the integrity of the mechanical transmission components of S800 ENC.