Table of Contents
Advertisement
1. KNOW YOUR TOOL
Read and understand the owners manual and labels affixed to
the tool. Learn its application and limitations as well as its
specific potential hazards.
2. GROUND THE TOOL.
This tool is equipped with an approved 3-conductor cord and a
3-prong grounding type plug to fit the proper grounding type
receptacle. The green conductor in the cord is the grounding
wire. NEVER connect the green wire to a live terminal.
3. KEEP GUARDS IN PLACE.
Keep in good working order, properly adjusted and aligned.
4. REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and adjusting wrenches
are removed from tool before turning it on.
5. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents. Make sure the
floor is clean and not slippery due to wax and sawdust build-up.
6. AVOID DANGEROUS ENVIRONMENT.
Don't use power tools in damp or wet locations or expose them
to rain. Keep work area well lit and provide adequate
surroun-ding work space.
7. KEEP CHILDREN AWAY.
All visitors should be kept a safe distance from work area.
8. MAKE WORKSHOP CHILD-PROOF.
-with padlocks, master switches or by removing starter keys.
9. USE PROPER SPEED.
A tool will do a better and safer job when
proper speed.
10. USE RIGHT TOOL.
Don't force the tool or the attachment to do a job for which it was
not designed.
11. WEAR PROPER APPAREL.
Do not wear loose clothing, gloves, neckties or jewelry (rings,
watch) because they could get caught in moving parts. Non-slip
footwear is
recommended. Wear protective hair covering to
contain long hair. Roll up long sleeves above the elbows.
SPECIFIC SAFETY INSTRUCTIONS FOR ROUTER TABLE ATTACHMENTS
1. NEVER USE ROUTER TABLE FENCE WITH TABLE SAW.
The router table fence is not designed to be used with the table
saw, this creates an unsafe work situation. Never try to use the
router table fence with the table saw blade.
2. FENCE AND ROUTER BIT GUARD PROPERLY POSITIONED.
Before plugging in the router power cord, make sure the router
table fence and router bit guard are correctly positionned and
secured. This will reduce the risk of injury from accidental contact
with the router bit during use.
GENERAL SAFETY INSTRUCTIONS
FOR POWER TOOLS
operated at the
12. ALWAYS WEAR SAFETY GLASSES.
Always wear safety glasses (ANSI Z87.1). Everyday eyeglasses
only have impact resistant lenses, thet are NOT safety glasses.
Also use a face or dust mask if cutting operation is dusty.
13. DON'T OVERREACH.
Keep proper footing and balance at all times.
14. MAINTAIN TOOL WITH CARE.
Keep tools sharp and clean for best and safest performance.
Follow instructions for lubricating and changing accessories.
15. DISCONNECT TOOLS.
Before servicing, when changing accessories or attachments.
16. AVOID ACCIDENTAL STARTING.
Make sure the switch is in the ''OFF'' position before plugging in.
17. USE RECOMMENDED ACCESSORIES.
Consult the manual for recommended accessories. Follow the
instructions that accompany the accessories. The use of
improper accessories may cause hazards.
18. NEVER STAND ON TOOL.
Serious injury could occur if the tool tips over. Do not store materials
such that it is necessary to stand on the tool to reach them.
19. CHECK DAMAGED PARTS.
Before further use of the tool, a guard or other parts that are damaged
should be carefully checked to ensure that they will operate
properly and perform their intended function. Check for alignment
of moving parts, breakage of parts, mounting, and any other
conditions that may affect its operation. A guard or other parts that
are damaged should be properly repaired or replaced.
20. NEVER LEAVE MACHINE RUNNING UNATTENDED.
Turn power ''OFF''. Don't leave any tool running until it comes to
a complete stop.
3. UNPLUG ALL POWER CORDS.
Before making any installation, repair or maintenance, unplug the
table saw and router power cords from the power source.
4. MAKE SURE ROUTER IS SECURED TO ROUTER TABLE.
If the router is not secured properly to the router table, causing
the router to move or the router bit to come in contact with the
fence or the table insert, serious personal injury could result from
flying debris. Make sure router is properly secured and router bit
is perfectly centred with the table insert.
Advertisement
Table of Contents
